Question about 2001 Mitsubishi Mirage

1 Answer

Finding transmission screen where and how i remove it

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 7,353 Answers

The screeen is inside the pan, i would just clean it. If there are any large amount of debris on the screen or in the pan, you have other problems.

Posted on May 10, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to find the transmission dipstick in a 2011 Kia Sportage


The transmission dipstick will be closer to the firlewall on most vehicles It may have a handle with a picture of a transmission on it. You'll need to find the transmission drain plug if there is one. Some models you need to drop the transmission pan some you have to drop the oil pan before you can drop the transmission pan. Many you have to remove brackets and or exhaust parts before you can remove the other pans. See Tutorial

Nov 27, 2013 | 2011 Kia Sportage

1 Answer

How do I take a transmission out of a 1980 chevy truck? Can u take out the motor and transmission and transfer case at one time


All of this is usually removed at once the way I know of to allow more room to remove transmission bolts etc. Start by marking all hoses, lines and electricial connectors. then disconnect. Next find all mechanical connections, in example; connections from transmission to shifter and exhaust. Find suitable connections for engine hoist to lift motor. Keep in mind you will need to balance the transmission, but, it will be much lighter than the motor. Find and loosen motor and transmission mounts. Start lifting motor with engine hoist and remove connections to mounts as needed. When you are doing this be sure to stay out of possible pinching areas where you can be pinched or squashed by shifting weight. If you havent done so, I would remove fan and radiator because they can be easily damaged. From there lift the engine out, most likely it will take a little push and shove. Just be careful and you will get the job done!!!

Sep 14, 2010 | Chevrolet 1500 Cars & Trucks

1 Answer

I need to know how to change the transimission filter on a 1996 ford thunderbird v8. Or at lest where to find a diagram on how to do it


Copied from AutoZone.com:


REMOVAL & INSTALLATION


See Figures 1 and 2
  1. Raise and safely support the vehicle on jackstands.
  2. Place a drain pan under the transmission.
  3. Loosen the pan attaching bolts and drain the fluid from the transmission.

Always place used fluids and oils into a sealed storage container and take to an approved recycling collection facility. Never dump used fluids or oils on the ground or in a trash receptacle. Contamination to the environment can and will occur.
  1. When the fluid has drained to the level of the pan flange, remove the remaining pan bolts working from the rear and both sides of the pan to allow it to drop and drain slowly.

Some AOD transmissions will have a plastic plunger type plug floating loosely in the pan when draining the fluid. It is of no importance and was used in the assembly process of the transmission. Discard it before reinstallation of pan.
  1. When all of the fluid has drained, remove the pan and clean it thoroughly. discard the pan gasket. If equipped, remove the pan magnet.




0900c1528006bc40.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: Unfasten the remaining bolts, then remove the transmission fluid pan from the vehicle



0900c1528006bc41.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: On some vehicles, such as this 1995, you must remove and clean the pan magnet
To install:
  1. Place a new gasket on the pan, then install the pan on the transmission. If equipped, don't forget to install the pan magnet. Tighten the pan attaching bolts as follows:

    C3 and C5 Transmissions: 12-16 ft. lbs. (16-22 Nm) A4LD Transmissions: 8-10 ft. lbs. (11-13.5 Nm) AOD Transmissions: 71-119 inch lbs. (8-13 Nm) 4R70W Transmissions: 9-11 ft. lbs. (12-15 Nm)
  2. Add the correct type and quantity of fluid to the transmission through the filler tube.
  3. Lower the vehicle. Start the engine and move the gear selector through shift pattern. Allow the engine to reach normal operating temperature.
  4. Check the transmission fluid. Add fluid, if necessary, to maintain correct level.


FILTER SERVICE


See Figure 3
  1. Remove the transmission oil pan and drain the fluid. For details, please refer to the procedure located earlier in this section.
  2. Remove the screen and the filter from the valve body. Most screens are retained using a fastener; through some may use an interference fit between the screen tube and valve body.




0900c1528006bc42.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 3: After the pan is removed, you can remove the transmission fluid filter
To install:
  1. Install a new filter using a new gasket or O-ring.

If the transmission uses a filter equipped with a fully exposed screen, it may be cleaned and reused.
  1. Install the transmission oil pan and properly refill the transmission.

Aug 26, 2010 | 1996 Ford Thunderbird LX

1 Answer

Manual transmission, 4 cylinder, removing from vw ...


IF YOU REMOVE ALL SIDE MOUNT BOLTS AND TRANSMISSION MOUNT BOLTS REMOVE SHIFT AND RELAY SHAFT RODS IF EVERYTHING BEEN REMOVED AND DISCONNECTED TRY PRYING TRANSMISSION AWAY FROM ENGINE.DO IT EASY NOT HARD TRANSMISSION COULD BE CAUGHT ON SOMETHING.

May 16, 2010 | Cars & Trucks

2 Answers

Reverse went out on 1978 Chevy pickup


Nothing. Also it will be much cheaper to find a used matching transmission with low (less than 80k miles) than having a shop rebuild the old one. In most cases the used transmission will far outlast the rebuilt one. Check on the web by Googling "used transmissions".

May 04, 2010 | 1978 Chevrolet C1500

2 Answers

How do I find automatic transmission filter in


it probably dont have an externall filter. and only a screen inside.dont mess with the screen they never need service. if the screen were plugged it woild be because the transmission failed.

Mar 20, 2010 | 2001 Hyundai Elantra

1 Answer

Where do you find the stick to check the the transmission fluid


Find the transmission fluid level plug, which is usually on the front of the transmission pan. Remove it using an 11mm flare nut wrench. Be careful not to lie directly beneath the plug when removing it because hot transmission fluid could spill from the opening. Have an empty container or jug on hand to catch any spilling fluid.

Check the ATF level by observing the spillage. If fluid spills from the transmission fluid level plug opening after removing the plug, the ATF level is too high. Remedy this by waiting until the spillage stops and replugging the opening. If no spillage occurs, the fluid could be too low.

Mar 06, 2010 | 1998 Chevrolet Malibu

1 Answer

Cant find transmission flter on my car to replace it


you have to remove the transmission fluid pan-it is not an external filter
first remove the transmission drain plug and then remove the pan-you can then remove the filter and transmission pan gasket

Feb 18, 2010 | 2003 Mitsubishi Outlander

1 Answer

Replace wiper motor


Wiper Motor
  1. Remove the wiper blade and arm assemblies, as outlined earlier in this section.
  2. Turn the ignition ON and the wiper switch OFF so the wiper motor returns to the park position.
  3. Disconnect the negative battery cable.
  4. Unfasten any necessary retainers and remove the air inlet screen assembly. Disconnect the washer hoses.

e828ab6.gif
Remove the air inlet screen retaining bolts/screws ...


d3d9288.gif
... then remove the air inlet screen


79f8835.gif
Disconnect the windshield washer fluid hose(s)


  1. Disconnect the wiper arm transmission drive link from the crank arm using a suitable wiper transmission separator tool.


9299629.gif
There is a special tool available to separate the transmission drive link from the crank arm


76dac5f.gif
View of the transmission drive link separated from the crank arm

On some vehicles, it may be necessary to remove the nut from the ball crank and remove the crank arm.


7e68234.gif
Location of the wiper arm ball crank


51c4507.gif
If necessary, unfasten the ball crank retaining nut, then remove the crank arm

Detach the electrical connectors from the wiper motor. Remove the wiper motor mounting bolts/screws.

Feb 06, 2010 | 1997 Buick LeSabre

1 Answer

How to change the automatic transmission oil and filter. On 4 cylinder engine


Check fluid level every 12 months or 7500 miles, whichever comes first. Transmission fluid and filter should be changed every 100,000 miles. On THM 250C transmissions, intermediate (front) band requires adjustment every 60,000 miles, or as required.
1. With vehicle on level surface, apply parking brake and let engine run at curb idle. Move selector lever through all ranges, ending in "PARK". Remove dipstick and wipe clean, reinstall, then remove again and check fluid level mark on dipstick. Fluid level should check between "ADD 1 PT." and "FULL HOT" marks on dipstick.
RECOMMENDED FLUID Use only Dexron II or equivalent automatic transmission fluid.
CAUTION: If vehicle has been operated for an extended period of time at high speed, or in city traffic in hot weather, or if vehicle has been pulling a trailer, an accurate fluid level cannot be determined until fluid has cooled down (approximately 30 minutes after vehicle has been parked).
So let's get started... 1. With vehicle raised and drain pan placed under transmission, remove front and side transmission oil pan bolts. Loosen rear pan bolts approximately 4 turns each.
2. Carefully pry pan loose with screwdriver, allowing fluid to drain. Remove remaining bolts and oil pan with gasket. Remove screen/filter-to-valve body bolts and remove screen/filter with gasket.
3. Thoroughly clean pan and screen with solvent and dry with compressed air. Paper type filters should be replaced. Install new gasket or "O" rings, lubricated with clean oil, into screen/filter assembly.
4. Install screen/filter assembly to transmission. Use new pan gasket and install pan. Add proper amount of fluid to transmission through filler tube.
5. Start engine with shift selector lever in "PARK" position and with parking brake set. Check fluid level and add as required. CAUTION: DO NOT overfill.

Best of luck :)

Oct 20, 2009 | 1986 Pontiac Fiero

Not finding what you are looking for?
2001 Mitsubishi Mirage Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...