Question about 1986 Ford Bronco II

1 Answer

Rear end How to remove the inside part of the rear end?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Expert
  • 312 Answers

It is quite a job, need to take cover off, pull both axles and then take out the obvious bolts. It is a delicate process to replace parts right so if you are not familiar with the project I would hire some help.

Posted on May 10, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the rear end axle on a 1995 poly traction police issued caprice classic


First off I think you mean Posi-traction which means both axles turn with power to the wheels. You remove the axle grease from the rear end draining it then you remove the cover try and do it slowly so that you don't make getting the old gasket off really hard after cover is off you will see the rear end look inside at the pinion gears the axle goes through them you will see how they are held on just remove the pins when putting back together use some axle grease on the splined ends and make sure that the housing and the cover is really clean so that the gasket seals properly ,nothing worse than rear end oil leaking.

Apr 20, 2015 | 1995 Chevrolet Caprice Classic

Tip

How To Install Replace Rear Inside Door Handle Mercury Grand Marquis 98-02...


How To Install Replace Rear Inside Door Handle Mercury Grand Marquis 98-02 1AAuto.com

on May 22, 2012 | 2001 Mercury Grand Marquis

Tip

How To Install Replace Rear Inside Door Handle Mercury Grand Marquis 98-02...


How To Install Replace Rear Inside Door Handle Mercury Grand Marquis 98-02 1AAuto.com

on May 22, 2012 | 1998 Mercury Grand Marquis

1 Answer

Doorhandle


for passenger side:
1. unclip screw cover 'center flap' of inside door opener plastic cover, flap is 3/8"x 3/8" (center of plastic cover)
2. remove phillips screw now showing
3. push fabric panel (edge of door opener plastic cover-at hinged end of chrome handle) to allow uncliping of edge of plastic cover (top rt & lwr rt (for passenger side) of plastic cover)
4. open chrome inside door handle to allow plastic cover to be removed-slide plastic cover toward rear, free end of door to remove cover
5. remove switch panel-gently pry with wide non maring pry bar (cover wide blade screwdriver using cloth) do rear of sw panel 1st (don't pry front edge)
6. slide switch panel toward rear to allow removal
7. remove large phillips screw under sw panel
8. remove the 2 plastic covers near top, hinge edge -use plastic spoon handles to encourage caps to pop off. May also require small screwdriver approx 1/8" in to complete pop off
9. remove the 2 phillips screws w/ captive washers
10. remove 3 phillips/hex screws along the bottom inside of door panel
11. on outside/rear edge of panel push the 2 center pins of each in about 1/8"-this allows the clip to be pulled out w/ pin pushed in
12. remove plastic cover (REAR OF SIDE MIRROR)-pull window edge up and back.
13. lift rear of door panel (not hinge edge) up allow hinge edge to pivot around lower pin in door (hinge edge)
14. remove the 2 rt edge "L" brackets (gently pry center plastic pin out) (note the color and replace as removed)
15. slowly peel the clear plastc away from the non hinged end to expose the plastic panel with 3 phillips head screws
16. remove the 3 screws and panel for access to door handle.
17. using access area now available unlatch the rod attached to exterior door handle (unclip plastic to rotate clip up to allow rod to slide out-toward hinged edge)
18. using access area now available remove rod from ext door handle from inside door area
19. remove the 3 -10mm head bolts
20. remove the ext door handle (bottom edge out first)
reverse order to replace door handle

Mar 24, 2014 | 2003 Toyota Avalon

1 Answer

Cannot get rear axle out of rear end


most axles you have to take off the differential cover and there will be a large pin that goes through the center of the carrier. this pin usually has a small bolt holding it in place. remove bolt and pin and that should allow you to push axle in enough to remove the c-clip on the end of the axle.then you can pull axle out of housing.

Dec 31, 2011 | Dodge Cars & Trucks

1 Answer

99 dodge ram van 3500 rear end loud nose when the veh is moving, i have checked the rear oil and it is full.


It could be bad pinion bearings, broken spider gears, etc. inside the differential. It could also be an axle bearing. Check the insides of your rear wheels to see if there is any rear-end grease coming out near the wheel end of the axle. If there is oil coming out, then you have a bad wheel bearing. Otherwise, you will have to remove the differential cover to check for metal particles in the rear end and to see if there are any broken gears.

Jan 10, 2011 | Dodge Ram 3500 Cars & Trucks

2 Answers

My 1996 camaro z-28 need the rear end replaced, so were is the id tag, that gives me the correct rearend , in hte car and should I pull out the complete rear end and have it rebuiled, and then reinstalled...


If you take the VIN # to a GM dealer they should be able to tell you the original rear end that the vehicle came with. If you are going to take the rear end to a shop they will be able to tell when they take it apart. If it is a posi rear end it will have a tag under one af the cover bolts (if it has not been removed) Once inside a posi rear end is immediately identifiable from the clutch pack. Also the number of teeth is stamped on each (pinion and ring) gear. Divide ring gear # by Pinion gear # to get rear end ratio. Didn't get directly to your question, but I hope this helps. Let me know. Thanks

Dec 24, 2010 | 1996 Chevrolet Camaro

1 Answer

How do you take apart the pasnager rear axle?


You need to remove the rear wheel and brake drum, support the axle housing with a good jackstand. Remove the rear diff cover and find the bolt that goes through one end of the spider gear shaft (smaller gears in center section) Be careful when removing shaft or turning gears that the small gears don't walk out of the housing. Once the shaft has been removed, push the axle in and remove the retaining clip on the inside end, then pull axle out. Reverse procedure to install.

Jan 16, 2010 | 2005 Jeep Grand Cherokee

1 Answer

How to remove rear axles on 90 gmc s15 to replace axle seals


You take off the differential cover in the middle of the rear end and theres a lock you slide out on both sides inside the rear end on the side walls each rear axel on both sides has one. Take them out and the axels will slide out.

Oct 04, 2009 | 1988 GMC S-15

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...