Question about 2000 Oldsmobile Alero

1 Answer

Break lights don't work, running lights and center deck lid light all work. Replaced bulbs and checked all fuses any ideas?

Posted by on

  • b_ware76 May 10, 2010

    I replaced it and the right and left break lights still don't work. The center light works just fine, all the running lights work fine as well as turn signals. All fuses have been checked/replaced. Any other ideas.

  • b_ware76 May 10, 2010

    I replaced it and the right and left break lights still don't work. The center light works just fine, all the running lights work fine as well as turn signals. All fuses have been checked/replaced. Any other ideas.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 110 Answers

Brake light switch under dash on pedal

Posted on May 10, 2010

  • gwgsr May 11, 2010

    the same light blue wire that powers high mount powers stop lamps. they split in L/H instrument panel junction block

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Running and license plate lights on deck lid not working. Back-up lights work. Bulbs are good. Qtr panel lights/brake lights work. Separate fuse for those, or wiring short?


Check for the presence of power at those junctures. If there then look for a bad ground. If not there you need to find out where the power is being tapped from and check out the fuses/relays in between.

Sep 15, 2016 | 2000 Buick Century

1 Answer

Brake lights don't work?


check the bulbs and fuses and brake light switch

Jun 06, 2013 | 1999 Jeep Wrangler

1 Answer

Passanger and third break light don't work, new bulbs and fuses installed. what should i check next?


I would check the turn signal switch first. The brake lights may go thru the switch depending on the configuration.

Aug 16, 2012 | 1992 Honda Accord

1 Answer

Mazda 6 sport sedan break lights not working after hid light conversion


Instructions Open the rear deck lid on the Mazda 6.Carefully remove the plastic finishing cover from the license plate light housing, using a small flat-head screwdriver to release the locking tabs. Pull the cover downward and off of the deck lid, exposing the license plate bulb.
Remove the old light bulb from the license plate bulb socket by hand. Wrap your new one in a paper towel and do not touch the bulb with your bare fingers. Insert the new bulb into the light socket. Install the finishing cover onto the light housing and push it upward until it clicks and locks into place.
Repeat Steps 2 and 3 to complete the LED light conversion on the opposite side of the deck lid. Test the new bulbs by turning on the headlights on the Mazda 6.
Mercedes Parts.






May 25, 2012 | 2004 Mazda 6

1 Answer

I have a 05 silverado all three break lights do not work. When I hook up my boat the break lights on my trailer function just fine. And all bulbs and fuses are good any ideas.


Have you checked the bulbs? Some people don't beleive all the lights can burn out at once but when one brake light is on they are all on and for the same amount of time.
If the bulbs are fine then check the connection where the trailer plug is to the main harness. Some of those connectors go between the main harness and the tail lights and the connector can go bad.

Sep 02, 2011 | 2005 Chevrolet Silverado 1500 2WD

1 Answer

Change break light


start by opening the rear gate (deck lid / trunk / boot) and using a small pointed tool , pop out the center of the retaining clips to loosen them to allow access behind the interior trunk liner.
This should allow you access to the rear of the tail light and the bulb holders / sockets to change the lights.
Do it right and replace all of the lights right away , keeping the old un-burnt bulbs as emergency spares.

Jul 15, 2010 | 2000 Ford Focus

1 Answer

1998 BMW 740i - I had a brake light out, replaced it, it won't


check where the wires go from the inside of the body to the out around the gromet. I did run into one that the wires rubbed. Also if the light are on the trunk lid check where they go through the trunk latch.

Sep 14, 2009 | 2006 BMW 750Li

1 Answer

1988 camry rear lights.


Look at the wiring harness that runs along the hinge on the trunk lid, driver side. Camrys with lights on the trunk lid are know to break one of these wires.

Sep 26, 2008 | 1988 Toyota Camry

1 Answer

Break light problem


Do you know if the brake light bulbs are working? (are the bulbs good?). (the bulbs have two parts, one for brake lights the other for running lights)
If the third brake light bulb is working the brake lights should be with good light bulbs.

Jul 22, 2008 | 2005 Honda Accord

Not finding what you are looking for?
2000 Oldsmobile Alero Logo

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...