Question about 1996 Nissan 200SX

1 Answer

P1320 trouble code.the car starts ok and after awhile it dies. Let it it sit for a few hours and then it starts again.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 110 Answers

Ignition primary signal missing problem in distributor

Posted on May 10, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Battery wont start the car ,ill charge the battery its ok for a few hours then its dead ,alt charging good ,battery is new,every fuse in both pannels are hot with key off please help


The battery dies after sitting for a few hours ? Parasitic drain on the battery ! With the key off all fuse's shouldn't be hot ! Bad ignition switch . Find a wiring diagram at www.bbbind.com an check power at ignition switch . Look on you tube , a lot of videos on basic electrical trouble shooting .

Nov 13, 2015 | Cars & Trucks

1 Answer

Car will start after awhile it bogs down and dies


The engine in this car is controlled by a computer, whenever you have a stall like this the computer will record a fault code for the event, you must have the system scanned to get that code, then based on the code you start the diagnostic to repair the problem, which in your case is likely a CKP sensor. But that is just a guess, don't replace anything until the testing confirms it is the problem.

Feb 02, 2012 | 2004 Pontiac Grand Prix

2 Answers

96 GMC Jimmy starts okay but dies after about 10 minutes. It will start again after sitting for awhile, then dies again. Have changed the fuel filter and pump...any other ideas?


If you have replaced the fuel pump and filter I would still check the pump pressure when it wants to die. Check for any trouble codes in the system also.

Sep 05, 2010 | 1996 GMC Jimmy

1 Answer

P1320 code appeared and we replaced the cam position sensor. It ran OK, but started rough until warm and next code showed #1 cylinder misfire. Replaced #1 coil and it ran great. Then later the engine light...


i just had the same problem in my bmw 325i. Probably vaccum leak or exhaust leak. Check that nothing came loose in these areas. It takes time for your car to learn the new CPS (cam pos. sensor) so give it a few days and reset the code again and see if it works.

Mar 12, 2010 | 2000 Nissan Maxima

2 Answers

Truck stops running let it sit for awhile it will start up again sometimes it will other times it won't


Check your ignition coil first....it may have a bad winding that seperates when it heats up.....check it as soon as the truck dies.....this is a common problem.

Nov 16, 2009 | 1995 Dodge Ram

2 Answers

P1320 trouble code plus


The P1320 code is essentially a coil primary voltage problem. This is traceable using a labscope or accurate DVOM and perhaps you can isolate one or two coils that still work but are close to failure...but there is a nissan service message recommending replacement of ALL coils with updated/improved models to prevent this type of failure. TCS/SLIP is traction control. Most likely you have a speed sensor issue. Be aware, some vehicles can falsely illuminate TCS because of low tire pressure in a single wheel.

Sep 09, 2009 | 2000 Nissan Maxima

1 Answer

Car dies and battery light comes on.


Will it crank over when it won't start? When It dies check for spark at the sparkplugs if none change the ignition module.
http://www.aceautomotive1.com FaQ and BLOG

Aug 01, 2008 | 1999 Chevrolet Cavalier

Not finding what you are looking for?
1996 Nissan 200SX Logo

196 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...