Question about 1987 Ford Bronco

1 Answer

Trying to install starter solenoid for 1987 Ford Bronco full size 302.5 engine. Cann't figure out color wire placement.

Posted by on

  • Zaraki May 11, 2010

    The wires to the starter solenoid are not hard to connect, and I can explain to you how to connect the wires. I will need to know if there are one or two push on type connectors to the starter solenoid, and what color are the wires for the push on connectors?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 27 Answers

Trying to install starter solenoid for 1987 Ford - b197472.jpg
As you can see all wires go with the loop on them go to the side nearest to the firewall, plug one on top and starter wire goes to the one closest to the battery.

Posted on Aug 01, 2010

  • lilomee2009 Jun 06, 2011

    Since my husban d of 28 yrs has been disabled, I have had to take alot of the grind myself. This DAmn Bronco! Whew, this am done, she runs just like the ole lovable pig she is. Thank you for your pic.
    My other hobby car is a 65 Mustang.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1987 FORD FULL SIZE BRONCO FUEL PROBLEM, SHUTS DOWN


The only way air can get in the fuel line is if you have a hole in it! Problem of course is were? I would run the fuel line from back to front and back again. Look for any wet spot that you can find. You may even have to drop the tank to ba able to look on top. I would suspect the problem is in the line before the high preasure pump, being as you are pulling air into the system. I have seen leaky lines allow air in, but not let fuel out.

Sep 12, 2009 | 1987 Ford Bronco

1 Answer

I have a 1987 ford bronco and will not start replaced the pick up coil and ignition module and coil and still not getting spark to start now I am stumped can some one please help?


check the wires to the module,im not too sure what color wire to check,its been 5 years since i worked on that issue on a ford truck,but i think its a white wire with a black stripe-basically power from the key-also check the fusible links by the starter solenoid on the inside fender

Aug 10, 2009 | 1987 Ford Bronco

2 Answers

1987 ford bronco engine wont start


there is a two piece control module and pick up in distributor you could replace these or try a used distributor

Jul 23, 2009 | 1987 Ford Bronco

1 Answer

Trying to replace the valve cover gasket on the passenger of my 1987 ford bronco and cannot seem to get to it?


remove the valve cover bolts. remove the valve cover. scrape off the old gasket material off the cover and the engine. put the new gasket in place and replace the bolts and tighten...dont over tighten.

May 23, 2009 | 1987 Ford Bronco

2 Answers

Firing order for 1989 full size ford bronco 302


13726548 #1 cyl is front pass side and count to back 1234 are on pass side.5678 are on driver side.# 5 being front

Apr 22, 2009 | 1989 Ford Bronco

1 Answer

Car will not start


take a test light and check the small wire that for the ignition switch, is there power going to the solinoid? if so then need to have someone start it and test to see if there power for sol to starter. if so then starter is at fault or just take a jumper from batter to starter and see if it works. if so then sol may be your issuel

Apr 07, 2009 | 1994 Ford Bronco

2 Answers

1987 bronco will not start


Ford used alot of fuseable links, mostly around starter selenoid, look around for them and everyone you find try pulling them apart if there bad or burnt they will pull apart and there is your problem. If you don't find one burnt, than its got to be in the wire comming from the switch, heck there might be one of them fuseable links in that wire too.I never had to go that far to find a burnt one it was always around the selenoid or starter.

Feb 12, 2009 | 1987 Ford Bronco

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

510 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...