Question about 1998 Ford Windstar

1 Answer

How do i change the coil - 1998 Ford Windstar

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Ford Expert
  • 260 Answers

Ignition Coil Removal

  1. Disconnect fuel charging wiring connectors from ignition coil (12029) and radio ignition interference capacitor (18801) .
  1. Disconnect ignition wires by squeezing locking tabs and twisting while pulling upward. how do i change the coil - e941a97.gif
  2. Remove four ignition coil retaining screws and remove ignition coil and radio ignition interference capacitor . Save radio ignition interference capacitor for installation with ignition coil .
Installation
  1. Position ignition coil and radio ignition interference capacitor to ignition coil mounting bracket.
  1. Install retaining screws and tighten to 4.5-7.0 Nm (40-61 lb-in).
  1. Apply Silicone Dielectric Compound D7AZ-19A331-A (Motorcraft WA-10) or equivalent meeting Ford specification ESE-M1C171-A to all ignition wire boots.
  1. Install each ignition wire connector to the proper terminal on the ignition coil . Make sure boots are fully seated.
  1. Connect fuel charging wiring (9D930) to the ignition coil and radio ignition interference capacitor .

Posted on May 12, 2010

  • Franklin May 11, 2013

    Ignition is saying #3 coil is misfiring

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the torque specs for the intake manifold?


misfire on cylinder 4 probably the coil change plugs and move coil to another cylinder if the misfire changes to that cylinder change coil as well.

I recommend changing all the coils at once though if over 60000 miles as the have a tendency to follow each other out.

Lt- jason

Jul 05, 2014 | 2000 Mazda MPV

1 Answer

#3 cylinder is misfiring ?


check ignition coils. you can swap with another cylinder coils and see if misfire changes to other cylinder. If it jumps to other cylinder where there you atached the coil from cylinder #3, change the coil.
You can also check Coil On Plug Boot for damage and simple change the part. very easy and cheap.

May 27, 2014 | 2006 Nissan Armada

1 Answer

;need engine diagram for coil pack


No.4 is at the gearbox end ...run the engine ,pull the plug off the coil and if there is no change then that's the problem...when you change the coil also change the plug

Apr 04, 2014 | 2002 Toyota RAV4

1 Answer

Engine diagram


coil 3 on early engines it is under the inlet manifold you have to remove it. you should also change all 3 plugs whilst manifold off the plugs can cause coil failure.we at the dealer I worked for changed all 6plugs and coils on jaguars advise, my advise change coils and plugs under manifold only the other 3 are easy access

Jan 17, 2014 | 2000 Jaguar S-Type

1 Answer

Multiple coil failure codes, recent trans change out. rough idle and hot backfire heard


bad coils that makes for misfire find out y the coils fail if its the coils or the coils power supply change the plugs to they got to be bad to

Jan 17, 2011 | 2001 Dodge Intrepid

1 Answer

Cyl one and four misfire. Just changed wires. Coil runs both


OK, if changing the wires doesn't help, and cylinders 1 and 4 are both controlled by the same coil, change the coil, in order to solve the problem. If that doesn't work, it could be the coil pack module it sits on.

Sep 24, 2010 | 2005 Kia Sorento

2 Answers

Changed coil pack that wasnt firing started fine


check the fire to the coil pack if it's present then check the pulse to the crank sensor

Jan 14, 2010 | 1999 Pontiac Firebird

1 Answer

Have 2000 limited 4.7. Has engine light on and checked codes,says #3 & 6 misfire. changed coils. but still have light and runs rough at 65-69 mph. A little rough at stop.


why would someone even start with changing the coils...usually a misfire is due to bad spark plugs..replace spark plugs, then go from there...just for a personal reference, the next time you want to see if your coils are bad, simply change out your bad two coils with two coils on the other side of the engine that are good...if they misfire code changes, then you know its a coil...if not, plugs...

Nov 16, 2009 | 2000 Jeep Grand Cherokee

3 Answers

Misfiring


Have your ignition coils replaced

Sep 04, 2009 | 2002 Dodge Stratus

Not finding what you are looking for?
1998 Ford Windstar Logo

1,572 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...