Question about 1983 GMC C1500

Open Question

I HAVE A ROCHESTER DUALJET 210. I NEED A TEARDOWN

I HAVE A ROCHESTER DUALJET 210. I NEED A TEARDOWN PIC SO I CAN SEE WHERE IT ALL GETS TOGETHER. THANKS I HAVE AN 1981 GMC PU

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

clifford224
  • 1975 Answers

SOURCE: need a pic. of the brake lite swich 1993 gmc pu

Should look like what's in the pictures below. I hope this helps and good luck.


clifford224_275.jpg
clifford224_276.jpg

Posted on Jul 29, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I know which 3.8 is in my 1984 El Camio 229 or 231?


3.8L (229 CID)The 229 cid (3,751 cc) engine was first introduced for the 1980 model year and was produced until 1984. This engine replaced the 250 cid in full-size Chevrolets and Camaros as the new base V6. Additionally, the intermediate Chevrolet Malibu and Monte Carlo also used the 229 cid as a replacement for both the 200 cid V6, and the 231 cid Buick V6. Both the Buick V6 and the 229 cid Chevrolet V6 are 90-degree V6 engines, and both are often referred to as the 3.8L V6. These engines should not be confused as being the same, and are completely unique engine designs.
The 229 cid has a 3.736-inch bore and a 3.48-inch stroke, identical to the Chevrolet 305 cid V8 engine. The 229 cid used the same 2.45-inch main bearing and 2.10-inch rod bearing diameters as the 200 cid V6 engine. Also like the 200 cid V6, the 229 cid used the same crankshaft with the 18-degree offset throws and the same 5.7-inch connecting rods with 0.050-inch narrowed ends. It came equipped with 1.84-inch intake valves and 1.50-inch exhaust valves. The 229 cid V6 was only equipped with a 2-barrel carburetor. For 1980 the 229 cid used a mechanical Dualjet. From 1981 to 1984 the electronic Dualjet was used along with the GM's CCC (Computer Command Control) system. The 229 cid was rated between 110 and 115 hp (86 kW).

Feb 25, 2013 | Chevrolet Cars & Trucks

1 Answer

Our 1985 Ford Bronco has accumulated debris in the "grated" slot between the windshield and the hood. Is there a recommended way to remove this (ie -is it accessible without extensive teardown)?


That panel should come off easily. Under the hood you should see the retaining screws holding it. Might be rusty as all heck now, and screws might break off, but can always be drilled and new screws attached, when you put it back together.

Jan 31, 2013 | 1985 Ford Bronco

1 Answer

Need a pic and specs on a 1979 gmc sierra grande carburetor


That is a Rochester carburetor--4 barrel, and these carburetor are notorious for problems. It's a hassle to repair because some of the flat plug in the passage ways will leak. We just drill them out, and install new plug with epoxy after the carburetor body has been thoroughly cleaned. Go to you local library they should have a repair manual on Rochester carburetors, or look on the Internet it has everything in it networking. GB...stewbsion

Aug 21, 2011 | GMC Sierra 1500 Cars & Trucks

1 Answer

Need a pic of the motor so I could put back together


I think you need more than a pic... What exactly do you need to put back together.

Oct 21, 2010 | 1991 Ford F150

2 Answers

My temp on my 99 tahoe 5-7 goes from 1/4 to 3/4 when first gets going then rides at 1/4 to 1/2 or 210 why and what is the temp supposed to ride at normally "warmed up"


It shouldn't go above 210. That is where the thermostat is supposed to keep it. More than likely, you need a new thermostat. It sounds like it is sticking closed until it gets hot enough to 'pop' it open. Then it operates normally. Change it before it stays stuck.

Good luck, and I hope this helped!

Feb 25, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

My 1985 chevy 305 gets 4mi to the gallon


Check your ignition timing at 3500 rpm you should have about 40 degrees of advance If not, something is sticking in the distributor, either the vacuum or mechanical advance. This will cause a big reduction in fuel economy. Also, check your tire pressure. The cfm on a rochester is really not important. The primary bores are so small and they are the only thing allowing the mixture in most of the time.

Jan 29, 2010 | 1985 Chevrolet C1500

1 Answer

How to synchronize and replace the timming chain?


Get a manual if you plan on a teardown, or rebuild of the 4.7. Tough motor to work on. Timing is a nightmare, and if you don't know what you are doing, you will bend and break alot of stuff. Get a manual.

Jul 21, 2009 | 1998 Jeep Grand Cherokee

1 Answer

1984 chevy s10 2.8l rochester carberator.


check all the vacuum lines and make sure there are no leaks, i had the same problem an thats all it was

Dec 09, 2008 | 1984 Chevrolet S-10

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

306 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...