Question about Jeep Wrangler

1 Answer

I have a 91 wrangler with a 4 cylinder engine and a 5 speed transmission. i shifted into 5th gear it felt like it jumped out of gear but now i have no fifth gear when i shift into fifth its like shifting into neutral there is no grinding or nothing

Posted by on

  • dwn1960 May 10, 2010

    yes thank you

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Expert
  • 4,070 Answers

Hi! If it goes smoothly on fifth gear but it feels like in neutral then I believe that the linkage or ball end is faulty. You will need to replace it to get it back to working. Hope this helps and have a good one!

Posted on May 10, 2010

  • dj_relly999
    dj_relly999 May 10, 2010

    You feel like the stick shift a little sloppy? It can cause a gear malfunction too.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

5th gear shifter linkage reverse


can i assume you pulled the side plug on tranny and the level
is right there? or gone way down, ever do a 50k service? to it?

M/T tranny (not auto) what engine? the m./t varies by HP of ENGINE.
If its really in 5th ( i bet not)
if the RPM rises fast that is called clutch slip
yes, clutch bad.
if not in 5th actual rpm will rise fast too. slip,
if the other gears wroke like 4th at wide open throttle up hill
gee the chutch is good.
so its not going in to 5th (for lots of reasons)
but 1 reason , is easy.

-AX 4/5/15 transmission
this tranny has a shift tower. (that thing on top that the shifter lever
fits in to)
most tranny that fail to actual shift into gear
is caused by a $1 plastic part failure
so pull the shifter off top of the shift tower.
and look, is the plastic buffer parts all bad, missing, cracked or
destoryed, sure they all end there... all.
i can also remove the shifter, lever.
and shift to 5ht by hand, and see that it DOES.
it either does, or does not.
if it does, the lever parts are bad.
that simple.
see part 61 (im guessing which of 5 tranny it is , )
http://cdn.liveoffroad.com/images/Aisin_AX5_Transmission.jpg

Feb 04, 2014 | 1994 Jeep Wrangler

1 Answer

How to find codes for check engine light on


Check Engine Light Codes and Meanings
Long blinks Short blinks Problem
1 1 Camshaft position sensor
1 2 Mass air flow sensor
1 3 Engine coolant temperature sensor
1 4 Speed sensor
1 11 EVAP control system (flow)
1 14 Fuel injection system right bank (too rich)
1 15 Fuel injection system right bank (too lean)
2 1 Ignition circuit
2 3 Closed throttle position switch
2 5 Idle speed control
2 9 Fuel Injection system left bank (too rich)
2 10 Fuel Injection system left bank (too lean)
3 1 ECU
3 2 Exhaust gas recirculation system flow problem
3 3 Front left O2 sensor
3 4 Knock sensor
3 5 Exhaust gas recirculation temperature sensor
3 6 EGRC-BPT valve
3 7 Closed loop control
3 8 Closed loop control
4 1 Air intake temperature sensor
4 2 Fuel tank temperature sensor
4 3 Throttle position sensor
4 7 Crankshaft position sensor
5 3 Front right O2 sensor
5 4 Automatic transmission control unit
6 3 Cylinder #6 misfire
6 4 Cylinder #5 misfire
6 5 Cylinder #4 misfire
6 6 Cylinder #3 misfire
6 7 Cylinder #2 misfire
6 8 Cylinder #1 misfire
7 1 Multiple cylinder misfire
7 2 Three way catalytic converter (right side)
7 3 Three way catalytic converter (left side)
7 4 Evaporative emission control system pressure sensor
7 5 Evaporative emission control system
7 7 Rear O2 sensor
8 1 Vacuum cut valve bypass valve
8 2 Crank position sensor
8 3 Absolute pressure sensor
8 4 Automatic transmission control unit
8 6 Evaporative emission canister purge control solenoid valve
8 7 Evaporative emission Canister purge control solenoid valve circuit
9 1 Front Right O2 sensor
9 3 Evaporative emission Canister vent control valve
9 5 Crankshaft position sensor
9 8 Engine coolant temperature sensor
10 1 Front left O2 sensor
10 3 Park and Neutral position switch
10 5 EGRC solenoid valve
10 8 Evaporative emission canister purge volume control valve
11 1 Inhibitor switch
11 2 Revolution sensor
11 3 Improper shifting to first gear (Automatic transmission)
11 4 Improper shifting to second gear (Automatic transmission)
11 5 Improper shifting to third gear (Automatic transmission)
11 6 Improper shifting to fourth gear (Automatic transmission)
11 7 Solenoid valve lock up function
12 1 Shift solenoid B (Automatic transmission)
12 3 Overrun clutch solenoid valve (Automatic transmission)
12 4 Torque converter clutch solenoid valve (Automatic transmission)
12 5 Line pressure solenoid valve (Automatic transmission)
12 6 Throttle position sensor (Automatic transmission)
12 7 Engine speed signal
12 8 Fluid temperature sensor
13 2 MAP/BARO Switch Solenoid Valve
13 5 Fuel pump control module
13 8 Cooling fan

Dec 12, 2011 | 1995 Nissan Maxima

1 Answer

1989 Ford F-150 4.9L 300 inline 6 cylinder 5 speed stuck in 3rd Gear? any solutions


If your clutch master cylinder is good in all other gears: you can disengage and, shift the other gears with the engine not running and, you have the correct amount of clutch fluid
in your clutch master cylinder: to release the clutch:
you have a broken 5th gear syncro and, a bent fork
remove the transmission and, when you remove the shift cover you will
see the problem; you must drain the transmission case remove any metal debris; remove the gear set and, replace the syncro...the fork can probably be
re-straightened use clean, new case oil when you reassemble the transmission.

Aug 04, 2010 | 1989 Ford F 150

2 Answers

WHY IS MY CAR JUMPING OUT OF FIFTH GEAR? I HAS BEEN RUNNING OKAY NO NOISE . 1993 MAZDA 626 5 SPEED 4 CYLINDERS


A synchronizer for 5th gear is bad,needs to be replaced,the transmission needs to be removed ,and repaired.

May 04, 2010 | 1993 Mazda 626

2 Answers

1989 jeep wrangler wont shift gear and clutch gone loose


Get the clutch slave cylinder and master cylinder looked at.One of the 2 has failed.If the pedal goes to the floor or is very loose,this is very likely the cause.Not an expensive fix.Hope this helps

Jan 10, 2010 | 1989 Jeep Wrangler

2 Answers

300Zx will not shift out of 5th gear


Dear javatrader: There are very few solutions to this problem. The fact that you had mentioned 5th & Reverse, tells me that you problem is has two possibilities. Both relate to the same component.
The shift fork for Fifth gear and reverse are the same as well as the hub which the fork fits over.
When you Move the stick shift, it moves one of 3 rails in the transmission of which one is 5th and reverse. The hub is what locks the transmission in gear. The gears are what are referred to as synchromesh. This means that when you shift from gear to gear, it makes it possible to easily make the transition without the gears grinding while the car is in motion. The synchros are in fact, kind of a "BRAKE" for the gears so that when you go to shift into that gear, the synchronizing ring, slows the gear down enough to match the speed of the counter gear allowing it to engage with it, without grinding. As the hub slides into gear, there are spring loaded "KEYS" which are small pieces of steel about 1/2 inch long, 1/4 inch thick and 1/4 inch wide with a little hump in them to push up into a small cavity machined into the hub when it slides over it, thus locking the gear into place until you pull the stick to move it out of place. If a key pops out, it could cause the gear to stick, not allowing you to pull the hub back because the key has popped out at an angle which prohibits the hub from sliding over it.
Another possible senario: The fork is secured to the shift rail with a part called a "Roll pin". If this part shears, the car will be stick in what ever gear it was in at the time the pin sheared. If the pin shears, the stick will still move out of 5th gear position but the transmission won't.
This problem, unfortunately is not one a layman can fix. This is best left to a professional.
Good luck......If you are pleased with my answer, please write in, that you are satisfied with my answer. I am new in this "FIXYA" group and need more people responding to work my way up the ranks.

Mar 26, 2009 | 1987 Nissan 300ZX

1 Answer

2000 jeep wrangler are sythetic lubes used in axils and trans


Hello grega1967, your Jeep Wrangler came from the factory with gear oil in the axles and manual transmission, but the transfer case uses transmission fluid. It is a NP231 and your axles are Dana 30 in the front and Dana 35 in the rear. They should have a 4.10 gear ratio due to you having a 2.5 liter 4 cylinder.

I hope this helps,

map6260

Mar 12, 2009 | 2000 Jeep Wrangler

1 Answer

No hi gears making jumped chain noise/ 90 somethin wrangler 5 spd


If the chain in the transfer case broke, they don't fall off, you would know. It would make the noise all the time. The noise your hearing is most likley from the transmission. If you have the 2.5L engine you have an ax5 transmission, the 4.0L came with an ax15. Both transmissions work basicly the same. Gears 1-2 share a shift fork, so do 3-4. I would guess that you have'nt got to 5th gear. There is most likley a problem with the shift fork or the gear synchronizer. You cant be sure till you open it up. The hardest part about working on transmissions is getting over the fear of working on transmissions. I have been fixing cars for about twelve year now and still get a kick out of good mechanics who are afraid of transmissions. If your a farly handy person, its not that hard to take the top off and look. Buy a shop manual and remove the shift lever and the cover under it. The shift forks will come out with the cover, and the rings that they attach to in the transmission are the synchronizer's. If you get that far you'll figure out whats wrong. Bad synchronizer's mean the tranny's coming out. Hope this helps.

Jan 04, 2009 | 1999 Jeep Wrangler

1 Answer

5th. Gear


Sounds like you may have bent a shift fork or your cluster gear has some missing teeth on it now. I would venture to say that is it a bent shift fork. This will require the transmission be removed to gain access to inspect and repair.

Dec 06, 2008 | 1992 Jeep Wrangler

1 Answer

1998 jeep wrangler


shift tranny from 1st-3rd if engine revs up clutch needs replacing

Nov 01, 2008 | 2003 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...