Question about 2007 Mercedes-Benz C230 Sedan

1 Answer

Gear box bearing replacement on 1982 MB 230E I also need to purchase technical specification Manuals

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 17 Answers

Alldatadiy.com I love this site.

Posted on May 10, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 73 65 hp evinrude Replaced crank bearing Now only rotates counter clock wise Any ideas. Could be lower unit? Tx


need to be a bit more specific
what do you mean by crank bearing
It is a crankshaft bearing or bearings in the gear box of the leg where the prop is
if you have been working on the lower end of the leg then you may have replaced the direction dog in back to front or have the selector arm around that dog not in the groove so that it is holding the dog back in the reverse direction

May 24, 2016 | Cars & Trucks

2 Answers

Gear box replace 1999 toyota prado


land cruiser
gear box.
steering gear.
manual transmion, what? A/T?
transfer case.
what> gear is bad, name it . what mode of driving, 4wd, 2wd>? 4LO
what?

May 27, 2014 | 1999 Toyota RAV4

1 Answer

What parts will I need when changing a flex plate?


While you have the transmission removed be sure to replace the rear main bearing seal.On a1982 you will have to remove the oil pan to replace the seal,It has a two piece seal.After removal of the oil pan carefully remove the back main bearing cap,you will have to use a straight pick to roll the top seal out of the block.Lubricate the deal with oil before you install it.Be sure to get a new oil pan gasket with your other parts.Make sure you torque your main bearing cap to manufacturer's specifications.

Jan 31, 2010 | 1982 Ford F 150

1 Answer

Clutch and all components


check gear oil or replace bearing

Jan 26, 2010 | 1982 Ford F 150

2 Answers

Broken. want to repair self and need manual


hi, try canell.co.uk for free manual downloads

Oct 14, 2009 | 1982 Porsche 911

1 Answer

Removing Gear box From 2001 Hyundai Santa fe, is The Clutch A push Or Pull Type? and If It is a pull type how can you get the throw out bearing to let go to enable you to remove the G box from the vehicle


It's the 'pull' type. Remove the 14mm nut from the fork shaft release lever. 3996b16.gif
You'll have to manage to remove the release bearing from the pressure plate and return it to its slide shaft at the release fork on the transmission side before you can reinstall the trans (unless of course you're replacing them).
Go to http://www.hmaservice.com/ and register (vehicle by VIN). Afterward, you'll have access to technical information (manuals, wiring diagrams, service bulletins, etc) about your vehicle.

Jun 28, 2009 | 2001 Hyundai Santa Fe

1 Answer

Hyundai excel gear box 99


Go to http://www.hmaservice.com/ and register (vehicle by VIN). Afterward, you'll have access to technical information (manuals, wiring diagrams, service bulletins, etc) about your vehicle.

Jun 03, 2009 | 1994 Hyundai Excel

1 Answer

I need torque specs for head bolts on 1992 merc benz 230 e


hello,230e with engine 102.982,cylinder head bolt,double hexagonal socket m12, stage 1, 55 newton meter,stage 2 90 degrees stage 3 90 degrees,4 pcs. bolt with m8 tighten to 25 nm.ref. technical data year 1993,ty

Apr 17, 2009 | 1992 Mercedes-Benz E-Class

Not finding what you are looking for?
2007 Mercedes-Benz C230 Sedan Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

yadayada
yadayada

Level 3 Expert

77169 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...