Question about 2002 Chevrolet Silverado

2 Answers

Need to locate the crank position sensor on a 2002 silverado

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 17 Answers

Go to Autozone, they can pull up a spec sheet for you for free and give you the instructions on how to replace it.

Posted on May 10, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 466 Answers

The crankshaft sensor is located in front of the engine at the bottom of pulley crank.thanks

Posted on May 10, 2010

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

  • 50 Answers

SOURCE: crank position sensor location

you will need to remove the starter to gain acess to the ckp sensor. once you remove the starter look on the engine block and you will see the sensor. The only problem with doing this repair yourself is that you will not be able to preform the crankshaft position variation learn procedure with out a factory scan tool. The vehicle may crank an run, but the timing advance curves will be wrong so the vehicle will probably cut off every time you remove your foot from the gas pedal. Hope this info helps!

Posted on Aug 18, 2008

  • 30 Answers

SOURCE: where is the crank position sensor located?

it should be by the dampner/crank pully

Posted on Jul 17, 2009

MNfisherman
  • 11896 Answers

SOURCE: crank sensor position location

Follow your plug wires to coil pack and module. Once you found the module, follow the wires from there to crank sensor on engine block.

Posted on Aug 06, 2009

  • 521 Answers

SOURCE: looking for the location of the crank position

Crank sensor; right (pass.) side of block above the starter. You may have to remove the starter to remove the crank sensor.

Knock sensor: There may be 2, a front and a rear. Both would be UNDER the intake manifold on top of the engine block one behind the other about 8 inches or so apart. The manifold and associated item may or may not need to be removed to access the sensors.

Posted on Aug 10, 2009

deanot26508
  • 77 Answers

SOURCE: trying to locate where the crank position sensor

Look behind the starter, you may need to remove the starter to get to it.

Posted on Sep 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Throttle sensor location


on the throttle body on inlet manifold

Jun 29, 2014 | 2002 Chevrolet Silverado 1500

1 Answer

I have a 2002 chevy silveroda . I need to find the location of the crankshaft position sensor


should be on bottom of crank on left side behind the pulley.. the big metal ring with teeth on it on front side of motor..

Dec 02, 2011 | 2002 Chevrolet Silverado 1500

2 Answers

What is code P1345?


I had the p1345 on my 2002 Silverado this week. The code means Crankshaft/camshaft position correlation. In other words the cam is not where it is supposed to be in reference to the crank. It could be the Cam position sensor, the crank position sensor , the gear on the distributor or the timing chain. The quickest and cheapest check is the distributor gear which is what mine was. It's quite common. The gear is about $60 and can be replaced in less than an hour with the right experience. The engine won't usually run if it's the crank sensor and the cam sensor is a little more.

May 27, 2010 | 2002 GMC Sierra

2 Answers

Where is the crank shaft positioning sensor located on a 2002 sunfire with a 2.2 ecotec


the crank position sensor is located to the back of the engine to the left of the oil filter, it is right next to the oil filter on the back side of the engine. hope this helps. Please rate my fix as i strive to be the best. need more help, get back to me Thanks Ray

Dec 10, 2009 | 2002 Pontiac Sunfire

1 Answer

Crank Sesor Location?


Ck Front of engine around the crankshaft pully.

Sep 16, 2009 | 2001 Chevrolet Silverado

1 Answer

Looking for the location of the crank position sensor and the knock sensor for a 2001 chevrolet silverado with a 4.8 8cylinder engine


Crank sensor; right (pass.) side of block above the starter. You may have to remove the starter to remove the crank sensor.

Knock sensor: There may be 2, a front and a rear. Both would be UNDER the intake manifold on top of the engine block one behind the other about 8 inches or so apart. The manifold and associated item may or may not need to be removed to access the sensors.

Aug 10, 2009 | 2001 Chevrolet Silverado

1 Answer

Can't find the location for the crankshaft position sensor


you need a haynes manual . because crank sensor can be behind crank pulley or on bottom side of engine that why you need a manual save you time.

May 13, 2009 | 2002 Nissan Sentra

1 Answer

Crankshaft position sensor


Here is a Pic of the location The arrow points to the CKP (crank position sensor) It is next to the pulse wheel.
008e032.png

Dec 14, 2008 | 2002 Daewoo Nubira

1 Answer

Where do color wires connect on crank position sensor Chevy 2000?


http://www.autozone.com/N,317019/initialAction,repairGuide/shopping/repairGuideVehicleSelect3.htm

follow this and figure out what truck you have. then put in the part you want and go to repair info on the left. It should give you the diagram you need.

Nov 24, 2008 | 2002 Chevrolet Silverado

Not finding what you are looking for?
2002 Chevrolet Silverado Logo

258 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6924 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...