Question about 2004 Lincoln Navigator

1 Answer

Headlamp low beam out for a 2004 Lincoln. When switch is turned on bulb will flicker but will not come on, that is with new replacement that is a excat match for replacement part.

Posted by on

Ad

1 Answer

Go back over what you did. I hope you didn't touch the lamp, and get oil from your hands on a halagon bulb.
The connector may not be on right
The new bulb ,may be no good,lost it's vacuum

Posted on May 10, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 f250 no high or low beam ,, have daytime lights, when I turn light switch have park lights no high or low beam , when I pull multifunction switch towards wheel and hold it I have high beam


Visual Inspection Chart Mechanical Electrical
  • Headlamp switch
  • Multifunction switch
  • Central junction box (CJB) fuse:
    • 7 (30A)
    • 30 (15A)
    • 46 (10A)
    • 47 (10A)
  • Circuitry
  • Headlamp bulbs
  • Daytime running lamp (DRL) relay No.1

Aug 10, 2015 | Cars & Trucks

1 Answer

Low beams gone on 2005buick lacross


look at the bulbs first.
there is the possibility that the headlamp switch is defective. Take the connector off and replace slowly to see if the connection is ok.
Put a jumper wire from battery to low beams. if this turns on the lights the switch is bad.
Then try the dimmer switch on steering column. Work back and forth a few times and watch for the lights to come on hard or flicker.
if the flicker replace switch assembly. again if nothing jumper the battery wire to low beams. If this turns the lights on replace switch.
Last the running lights module. jumper the wires again. replace if necessary.

Mar 15, 2013 | 2005 Buick LaCrosse

2 Answers

How do I replace the headlight bulb on a 2005 Town Car?


1. Remove the three pin-type retainers, two screws and the radiator defector.
2. Remove the 4 bolts securing the headlamp assembly and remove headlamp assembly.
- Disconnect electrical connector
3. Remove the 3 hex-head bolts and 2 torx-head screws and remove headlamp protective cover.
4. *****Standard low-beam bulb*****
Disconnect the connector from the bulb and remove the low beam bulb.
5. *****HID low beam bulb*****
Release the spring tabs and remove the HID low beam bulb
Disconnect the connector from the bulb
6. *****High beam bulb*****
Disconnect the electrical connector and remove the high beam bulb.
Reverse order to install
dttech_6.gif
.
.

dttech_7.gif

Jan 27, 2011 | 2005 Lincoln Town Car

1 Answer

How do i remove bulb from socket for day time running light on 2002 avalanche


dak408_133.gif
  1. Open the hood.
  2. Remove the park/turn signal lamp assembly.
  3. Remove the headlamp retainer pins.
  4. Pull out the headlamp assembly in order to access the electrical connector.
  5. Disconnect the electrical connector.
  6. Remove the bulb from the headlamp assembly by twisting the bulb counterclockwise.
INSTALLATION PROCEDURE

IMPORTANT:
  • Replace a high beam bulb with another high beam bulb. The high beam bulb has a red gasket.
  • Replace a low beam bulb with another low beam bulb. The low beam bulb has a gray tip and a yellow gasket at the base.
  1. Install the new bulb to the headlamp assembly by twisting the bulb clockwise in order to lock in place.
  2. Connect the electrical connector to the bulb.
  3. Install the headlamp assembly.
  4. Install the headlamp retainer pins.
  5. Rotate and lock the pins in place.
  6. Install the park/turn signal lamp assembly.
  7. Inspect the operation.

Dec 11, 2010 | 2002 Chevrolet Avalanche

1 Answer

How to replace the high beam bulb on a 98 GMC Suburban. What needs to be removed to get to it?


Headlamp Bulb: Service and Repair
REMOVAL PROCEDURE
1. Make sure the headlamp switch is in the OFF position.
CAUTION: Halogen bulbs contain gas under pressure. Handling a bulb improperly could cause it to shatter into flying glass fragments.
To help avoid personal injury:
- Turn off the lamp switch and allow the bulb to cool before changing the bulb. Leave the lamp switch off until the bulb change is
complete
- Always wear eye protection when changing a halogen bulb.
- Handle the bulb only by its base. Avoid touching the glass.
- Do not drop or scratch the bulb.
- Keep dirt and moisture off the bulb.
- Place the used bulb in the new bulb's carton and dispose of it properly.
- Keep halogen bulbs out of the reach of children
NOTE
: Avoid touching the bulb or letting the bulb come in contact with anything damp. Oil from your skin or moisture on the bulb can cause
the bulb to explode when the bulb is turned on. It either comes in contact with the bulb, clean the bulb with alcohol or a suitable degreaser and
wipe the bulb dry.
2. Remove the bulbs from the headlamp capsules by reaching from the engine compartment and by twisting the bulb counterclockwise.
3. Remove the 2 long screws from the top of the radiator support.
4. Pull forward the headlamp assembly (3).
5. Disconnect the electrical connector (2) from the burned out bulb assembly (1).
INSTALLATION PROCEDURE
IMPORTANT
:
- Replace a high beam bulb with another high beam bulb. The high beam bulb has a red gasket.
- Replace a low beam bulb with another low beam bulb. The low beam bulb has a gray tip and a yellow gasket at the base.
1. Install the new bulb assembly (1) into the headlamp assembly (3).
Twist clockwise the bulb assembly.
2. Seat the bulb assembly with the connector facing down.
3. Connect the electrical connector (2) to the bulb assembly.
4. Install the headlamp assembly.
5. Install the 2 long screws through the top of the radiator support.
6. Tighten the screws.

Oct 30, 2009 | 1998 GMC Suburban

1 Answer

Front turn signal bulb replacement


HEADLAMP BULB REPLACEMENT

REMOVAL PROCEDURE

CAUTION: Halogen bulbs contain gas under pressure. Handling a bulb improperly could cause it to shatter into flying glass fragments. To help avoid personal injury:

  • Turn off the lamp switch and allow the bulb to cool before changing the bulb.
  • Leave the lamp switch OFF until the bulb change is complete.
  • Always wear eye protection when changing a halogen bulb.
  • Handle the bulb only by its base. Avoid touching the glass.
  • Keep dirt and moisture off the bulb.
  • Properly dispose of the used bulb.
  • Keep halogen bulbs out of the reach of children .
NOTE : Avoid touching the bulb or letting the bulb come in contact with anything damp. Oil from your skin or moisture on the bulb can cause the bulb to explode when the bulb is turned on. If either comes in contact with the bulb, clean the bulb with alcohol or a suitable degreaser and wipe the bulb dry.


  1. Open the hood.
  2. Remove the headlamp. Refer to Headlamp Replacement .
  1. Remove the access cover from the rear of the headlamp.
  2. Disconnect the electrical connector from the socket.
  3. Rotate the bulb and socket counter clockwise in order to remove the bulb and socket from the housing.
  4. Disconnect the electrical connector from the socket.
  5. Remove the bulb and socket from the headlamp.
INSTALLATION PROCEDURE

IMPORTANT :
  • Replace a high beam bulb with another high beam bulb. The high beam bulb has a black socket.
  • Replace a low beam bulb with another low beam bulb. The low beam bulb has a gray tip and a grey socket.
    1. Position the bulb and socket to the headlamp.
    2. Connect the electrical connector to the socket.
    3. Install the bulb and socket to the housing by rotating the bulb and socket clockwise, locking the retaining tabs to the housing.
    4. Install the access cover to the rear of the headlamp assembly
    5. Install the headlamp

REMOVAL PROCEDURE
  1. Open the hood.
  2. Remove the headlamp.
  3. Rotate the bulb and socket counter-clockwise in order to remove the bulb and socket from the housing.
  4. Remove the side marker bulb (3) or turn signal/park bulb (4) from the socket.
INSTALLATION PROCEDURE


  1. Install the side marker bulb (3) or turn signal/park bulb (4) to the socket.
  2. Wipe the bulb with a clean cloth to ensure the bulb is free of any dirt or oil.
  3. Install the bulb and socket to the headlamp by rotating the bulb and socket clockwise, locking the retaining tabs to the headlamp.
  4. Install the headlamp.

Jul 10, 2009 | 2004 Chevrolet TrailBlazer

1 Answer

Passenger headlight don't work 2003 lincoln navagator


high beam or low beam? or both of them on one side.

  • One low beam headlamp is inoperative
  • Central junction box (CJB) fuse 23 (10A) (RH headlamp).
  • CJB fuse 25 (10A) (LH headlamp).
  • Circuitry.
  • CJB.
  • Go To Pinpoint Test C .


  • One high beam headlamp is inoperative
  • Circuitry.
  • Headlamp assembly.
  • Go To Pinpoint Test D .

  • The high and low beam headlamp is inoperative on one side
  • Circuitry.
  • REPAIR ground circuit 57 (BK).


  • Headlamp switch
  • Multifunction switch
  • Vehicle Security Module
  • Central junction box (CJB) fuse(s):
    • 17 (15A)
    • 23 (10A)
    • 25 (10A)
    • 35 (20A)
    • 40 (20A)
  • Circuitry
  • Headlamp bulbs
  • Daytime running lamp (DRL) relay



Apr 19, 2009 | 2003 Lincoln Navigator

1 Answer

2004 Lincoln Navigator Low Beam Bulb replacement


your owner manual will list the bulb. It is expensive. tascafordparts.com for discount from Ford Dealer

here's 2003, don't have 2004

Navigator high intensity discharge (HID) headlamp
  1. Remove the front radiator air deflector.
  1. Remove the three bolts and the headlamp assembly.
    • Disconnect the electrical connectors.
1c293b4.gif
8. Remove the headlamp bulb protective cover(s).
  • Remove the HID lamp cover.
  • Remove the high beam cover.
  • Disconnect the electrical connector and push the grommet into the headlamp assembly.
7adecf7.gif
  1. Release the spring tabs and remove the HID low beam bulb.
3394a45.gif

Apr 11, 2009 | 2004 Lincoln Navigator

1 Answer

1994 ford f-150 with day time running lights headlightnot working


Daytime Running Lamps
The daytime running lamp (DRL) system is designed to turn the high beam headlamps on, with a reduced light output, and without illuminating the high beam indicator lamp in the instrument panel. You have a DRL Module.
The multifunction switch is the stalk on your column.

This is 96 F150 circuit. Don't have 94.

51f651c.gif
Symptom Chart, Headlamps HEADLAMPS Condition Possible Source Action
  • Headlamps Inoperative
  • Circuitry open/shorted.
  • Damaged headlamp switch.
  • Blown fuse.
  • GO to Pinpoint Test A .
  • Headlamps On Continuously
  • Circuitry open/shorted.
  • Damaged headlamp switch.
  • GO to Pinpoint Test B .
  • High Beams or Low Beams Inoperative
  • Circuitry open/shorted.
  • Damaged multi-function switch.
  • GO to Pinpoint Test C .
  • One High Beam or One Low Beam Headlamp Inoperative
  • Circuitry open/shorted.
  • Damaged connector.
  • Headlamp bulb damaged.
  • GO to Pinpoint Test D .
  • Flash-to-Pass Inoperative
  • Blown fuse.
  • Circuitry open/shorted.
  • Damaged multi-function switch.
  • GO to Pinpoint Test E .



73d6d64.gif

Feb 25, 2009 | 1994 Ford F150 Styleside Supercab

1 Answer

Replace low beam headlamp, passenger side, 2004 Navigator


Remove the front radiator air deflector.
Remove the three bolts and the headlamp assembly.
    • Disconnect the electrical connectors.
ef5d2b9.jpg
Remove the headlamp bulb protective cover.
1 Low beam cover. 2 High beam cover.

babb381.jpg
b8093f8.jpg

Feb 13, 2009 | 2003 Lincoln Navigator

Not finding what you are looking for?
2004 Lincoln Navigator Logo

Related Topics:

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

77201 Answers

fordexpert

Level 3 Expert

5579 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...