Question about 1996 Chevrolet C/K 3500

1 Answer

I have a 1996 7.4L gasoline, chevrolet 3500 that is not firing replaced the camshaft sensor,crankshaft sensor, ignition control module,and coil and replaced distributor cap rotor button plugs and wires,also checked all fuses and relays which are good.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,317 Answers

WOW!!! The only thing I could think of is the timing chain jumped time, or the engine is out of time. Do all the timing marks line up? Please let me know what you find!!!!

Posted on May 10, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Do a 2004 Envoy SLT 4.2L have a Ignition Module?


Crankshaft position sensor,cam sensor . your vehicle should have coil on plug , a coil at each spark plug !
Ignition Coils
Each ignition coil has an ignition 1 feed and a ground. The PCM supplies an ignition control (IC) circuit. Each ignition coil contains a solid state driver module as its primary element. The powertrain control module (PCM) signals the coil driver to initiate a firing event by applying a signal to the IC circuit at the appropriate time. When the signal is removed, the coil fires the spark plug. The spark plugs are tipped with platinum for long wear and higher efficiency.
During normal operation the powertrain control module (PCM) controls all ignition functions. If either the crankshaft position (CKP) or camshaft position (CMP) sensor signal is lost, the engine will continue to run because the PCM will default to a limp home mode using the remaining sensor input. As mentioned above, each coil is internally protected against damage from excessive voltage. If one or more coils were to fail in this manner, a misfiring condition would result. Diagnostic trouble codes are available to accurately diagnose the ignition system with a scan tool.
If a crank sensor is replaced a Crankshaft Position System Variation Learn must be done and a scan tool is need to do this.

Nov 30, 2016 | 2004 GMC Envoy SLT

1 Answer

How many camshaft sensors on a 1999 olds aurora


The Ignition Control System consists of the following components:
?€¢
Two crankshaft position sensors (A and B).


?€¢
Crankshaft reluctor ring.


?€¢
Camshaft position sensor.


?€¢
Ignition control module.


?€¢
4 separate ignition coils.


?€¢
Eight spark plug wires and conduit.


?€¢
Eight spark plugs.


?€¢
Knock sensor.


?€¢
Powertrain Control Module (PCM). Camshaft Position (CMP) Sensor
Right hand rear of the engine, near the power steering pump

Oct 01, 2015 | Cars & Trucks

1 Answer

How do replace ignition control module in 1998 K-1500 5.0 liter vortec


This system does not use the ignition module used on the DI systems in the past. The VCM controller now controls the ignition control (IC) and bypass functions.
The crankshaft sensor, located in the front engine cover, is perpendicular to a target wheel attached to the crankshaft. The target wheel is equipped with slots situated 60 degrees apart. As the crankshaft rotates, the target wheel rotates past the crankshaft position sensor. The rising and falling edges created by the slots cause a signal to be sent back to the VCM. This signal occurs three times per crankshaft revolution and is referred to as the 3x signal for V6 applications. The signal occurs four times per crankshaft revolution and is referred to as the 4x signal for V8 applications.
The VCM then utilizes this 3x (V6) or 4x (V8) signal in order to provide the correct spark to the engine by way of the single coil driver module. The single coil driver module is basically an electronic switch that when commanded by the VCM, causes the primary coil voltage to breakdown, energizing the secondary coil and providing a spark via the coil wire to the distributor cap. The distributor consists of the following components:
The system consists of the following components:
?€¢
Vehicle control module (VCM)


?€¢
Distributor


?€¢
Ignition coil driver module


?€¢
Ignition coil


?€¢
Crankshaft position (CKP) sensor


Now which part do you want to replace ?

?€¢
Cap and rotor


?€¢
Camshaft position sensor


?€¢
Gear drive and shaft

The camshaft drives the distributor shaft which rotates providing a spark to the correct cylinder by way of the cap and rotor. The camshaft position (CMP) sensor functions much like the crankshaft sensor previously described but provides only a 1x signal to the VCM. That is, for every 2 rotations of the crankshaft, there is 1 rotation of the camshaft. Note that the camshaft position sensor will not affect driveability. The sole purpose of the camshaft position sensor is to provide the VCM with the necessary information for the misfire diagnostic trouble codes (DTCs).

Sep 06, 2015 | 1998 Chevrolet K1500

1 Answer

Where is the distributor on a 2001 Cadillac deville?


Has no distributor - electronic ignition !
The electronic ignition system does not use the conventional distributor and coil. The ignition system consists of the following components/circuits:
?€¢
Eight ignition coils


?€¢
Eight ignition control (IC) circuits


?€¢
Two ignition control modules (one per cylinder bank)


?€¢
Camshaft position (CMP) sensor


?€¢
Crankshaft position (CKP) sensor A


?€¢
Crankshaft position (CKP) sensor B


?€¢
Related connecting wires


?€¢
Powertrain control module (PCM)

Jul 29, 2015 | Cadillac Cars & Trucks

2 Answers

I've replaced everything to do with ignition spark on ky 1998 gmc pickup it has a 350 vortech engine why am I jot getting spark at the spark plugs ?


There is a spark control modal in the distributor most books do not tell you about it . if you have replaced everything else try that

Apr 19, 2015 | GMC Cars & Trucks

1 Answer

Hey i just helped my friend put a motor in is 99 gt, it turns over but no spark from the coils, ive tried eveything i can think of and still nothing


what motor?

Is the PCM power relay activating? If yes, you should hear the fuel pump hum for 5 seconds when the key is turned to ON.

If yes, then check the crankshaft position sensor and camshaft position sensors to be sure they have output to the PCM.

The crankshaft position sensor:
  • sends the powertrain control module a signal indicating crankshaft position.
  • is essential for calculating spark timing.
Crankshaft Position Sensor (Integrated Ignition Systems) The crankshaft position (CKP) sensor is a magnetic transducer mounted on the engine block adjacent to a pulse wheel located on the crankshaft. By monitoring the crankshaft mounted pulse wheel, the CKP is the primary sensor for ignition information to the powertrain control module (PCM). The trigger wheel has a total of 35 teeth spaced 10 degrees apart with one empty space for a missing tooth. The 6.8L ten cylinder pulse wheel has 39 teeth spaced 9 degrees apart and one 9 degree empty space for a missing tooth. By monitoring the trigger wheel, the CKP indicates crankshaft position and speed information to the PCM. By monitoring the missing tooth, the CKP is also able to identify piston travel in order to synchronize the ignition system and provide a way of tracking the angular position of the crankshaft relative to fixed reference (Figure 23) .


Camshaft Position Sensor The camshaft position (CMP) sensor detects the position of the camshaft. The CMP sensor identifies when piston No. 1 is on its compression stroke. A signal is then sent to the powertrain control module (PCM) and used for synchronizing the firing of sequential fuel injectors. The Coil On Plug (COP) Ignition applications also use the CMP signal to select the proper ignition coil to fire. The input circuit to the PCM is referred to as the CMP input or circuit.
There are two types of CMP sensors: the three pin connector Hall-effect type sensor (Figure 20) and the two pin connector variable reluctance sensor (Figure 21).



A4 CHECK VREF VOLTAGE TO THROTTLE POSITION (TP) SENSOR
  • Disconnect TP sensor.
  • Key on, engine off.
  • Measure voltage between VREF and SIG RTN circuit at the TP sensor harness connector. Refer to the schematic in Pinpoint Test DH .
Is voltage between 4.0 and 6.0 volts? -------- A17 CHECK PCM DRIVER TO COILS
  • Connect incandescent test lamp between B+ and each coil driver circuit at the harness connector.
  • Crank engine.
Does lamp blink consistently and brightly (one blink per engine revolution)?

Jul 24, 2011 | 1999 Ford Mustang Cobra

2 Answers

305 vortec engine and has no fire need to know where to start, how to check crank sensor, or what else i need to check


if it died all of a sudden no warning, replace the ingition moduel located in the distrubitor. These are common to go out without warning and would cause no spark. It's like a $30 part and just simple tools needed to replace. If it went out over time let me know and I'll tell you what else to check.

Jun 06, 2010 | 1997 Chevrolet K1500

1 Answer

2004 Chevy Silverado HD 2500


On many engines with distributor less ignition systems and sequential fuel injection, a camshaft position sensor is used to keep the engine's control module informed about the relative position of the crankshaft. By monitoring cam position (which allows the control module to determine when the intake and exhaust valves are opening and closing), the control module can use the cam position sensor's input along with that from the crankshaft position sensor to determine which cylinder in the engine's firing sequence is approaching top dead center. This information is then used by the engine control module to synchronize the pulsing of sequential fuel injectors so they match the firing order of the engine. On some applications, input from the camshaft position sensor is also required for ignition timing.
The camshaft position sensor may be magnetic or Hall effect, and mounted on the timing cover over the camshaft gear, on the end of the cylinder head in an overhead cam application, or in a special housing that replaces the distributor (in the case of some of the GM applications). Operation and diagnosis is essentially the same as that for a crankshaft position sensor.  

Re  check the wire harness and the sensor installation to the camshaft sensor in Bank #1 which is where the #1 cylinder is. Good luck and hope this adds some light to you question, keep me posted and be glad to help.

Jun 02, 2009 | 2003 Chevrolet Silverado 2500HD

1 Answer

Timing the cams and crank with a belt


  1. Note: Electronic Ignition engine timing is entirely controlled by the PCM. Electronic Ignition engine timing is NOT adjustable. Do not attempt to check base timing. You will receive false readings.

The CKP sensor is used to indicate crankshaft position and speed by sensing a missing tooth on a pulse wheel mounted to the crankshaft. The CMP sensor is used by the COP Integrated EI System to identify top dead center of compression of cylinder 1 to synchronize the firing of the individual coils.
  1. The PCM uses the CKP signal to calculate a spark target and then fires the coil pack(s) to that target shown in Figure 51. The PCM uses the CMP sensor not shown in Figure 51 on COP Integrated EI Systems to identify top dead center of compression of cylinder 1 to synchronize the firing of the individual coils.
  1. The coils and coil packs receive their signal from the PCM to fire at a calculated spark target. Each coil within the pack fires two spark plugs at the same time. The plugs are paired so that as one fires during the compression stroke the other fires during the exhaust stroke. The next time the coil is fired the situation is reversed. The COP system fires only one spark plug per coil and only on the compression stroke.

    The PCM acts as an electronic switch to ground in the coil primary circuit. When the switch is closed, battery positive voltage (B+) applied to the coil primary circuit builds a magnetic field around the primary coil. When the switch opens, the power is interrupted and the primary field collapses inducing the high voltage in the secondary coil windings and the spark plug is fired. A kickback voltage spike occurs when the primary field collapses. The PCM uses this voltage spike to generate an Ignition Diagnostic Monitor (IDM) signal. IDM communicates information by pulsewidth modulation in the PCM.
  1. The PCM processes the CKP signal and uses it to drive the tachometer as the Clean Tach Out (CTO) signal.

2.5L V6

The ignition system consists of an ignition coil, spark plug wires and spark plugs.
The crankshaft position sensor signal is the basis for ignition timing calculations. The alternating voltage signal from the crankshaft position sensor is digitized by a pulse former within the powertrain control module. This digitized signal is then used to position the closing time of the primary circuit of the ignition coil.
Ignition timing is determined by the powertrain control module in response to engine operating conditions based on stored data tables or maps. Once ignition timing has been determined, the powertrain control module interrupts the current to the primary circuit of the ignition coil thus triggering the ignition spark which is supplied to the cylinders through the spark plug wires and spark plugs.
The ignition coils are triggered by the powertrain control module in pairs (cylinders 1 and 5, cylinders 4 and 3 and cylinders 2 and 6) sending one ignition spark to the firing cylinder and one ignition spark to the corresponding cylinder on the exhaust stroke. This ensures that any unburnt fuel residues remaining in the cylinder on the exhaust stroke are re - ignited to provide cleaner exhaust emissions.
---------------------------------------------------------------
2.0L 4 cynder

The ignition system consists of an ignition coil, spark plug wires and spark plugs.
The crankshaft position sensor signal is the basis for ignition timing calculations. The alternating voltage signal from the crankshaft position sensor is digitized by the powertrain control module. This digitized signal is then used to position the closing time of the primary circuit of the ignition coil.
Ignition angle is determined by the powertrain control module in response to engine operating conditions. Once ignition angle has been determined, the powertrain control module interrupts the current to the primary circuit of the ignition coil thus triggering the ignition spark which is supplied to the cylinders through the spark plug wires and spark plugs.
The ignition coils are triggered by the powertrain control module in pairs (cylinders 1 and 4 and cylinders 3 and 2) sending one ignition spark to the firing cylinder and one ignition spark to the corresponding cylinder on the exhaust stroke. This make sures that any unburnt fuel residues remaining in the cylinder on the exhaust stroke are re - ignited to provide cleaner exhaust emissions.
------------------------------------------------------------------------------------
Integrated Electronic Ignition System The Integrated Electronic Ignition (EI) System consists of a crankshaft position (CKP) sensor, coil pack(s), connecting wiring, and PCM. The Coil On Plug (COP) Integrated EI System uses a separate coil for each spark plug and each coil is mounted directly onto the plug. The COP Integrated EI System eliminates the need for spark plug wires but does require input from the camshaft position (CMP) sensor.
----------------------------------------------------------------------------------------

Apr 05, 2009 | 1998 Ford Contour

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...