Question about 2000 Hyundai Accent

1 Answer

Where is the crack sensor - 2000 Hyundai Accent

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,865 Answers

I am thinking that you mean crankshaft sensor. The sensor is located on the front of the engine block right above the starter you need to drop the starter and oil filter to remove the sensor. Joe

Posted on May 09, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I put new crack senser on car it cracked i drove it for awhile run good but later on that day started having the same problem again. start but wont crack


Did you check the oil? The low oil sensor will disable the ignition if more than a quart low. check oil often. Crank sensors rarely go bad

May 24, 2017 | Cars & Trucks

1 Answer

Will a bad crack sensor allow the car to start ?


crack?
grand am will not start with a defective crank sensor
it will however will start with a defective cam sensor

Jun 08, 2014 | 2003 Pontiac Grand Am

1 Answer

2002 Toyota forerunner fault code PO446


These are the listed trouble areas

Vacuum hose cracks, holes blocked, damaged or disconnected
Open or short circuit in vapor pressure sensor circuit
Vapor pressure sensor
Open or short in VSV circuit for EVAP
VSV or EVAP
Open or short in VSV circuit for vapor pressure sensor
VSV for vapor pressure sensor
Charcoal canister cracks, holed or damaged
ECM

Aug 23, 2013 | Cars & Trucks

1 Answer

Found a crack in the exhaust manifold


transmission solenoid and misfire code unrelated
but need looking into
02 sensor should be fixed with replaced 02 sensor
egr code only if crack is close by


cast iron zorst manifolds
if the crack takes up when engine is running
not urgent
when ready source
a used manifold without a crack from a wrecker
cracks in cast iron zorst manifolds cant be welded
sucessfuly

or buy (extractors )metal exhaust manifold
if they crack... they can be welded

Mar 07, 2017 | Cars & Trucks

1 Answer

I need answer for truck not firing. On. A 1991. SERRIA 1500 TRUCK 5.0 LITER


Several things can cause this problem, cracked distributor cap, old ignition rotor. Or if you have coil packs, cracked coil pack, ignition control module, crank position sensor, cam position sensor. Coil pack parts and sensors can be checked by autozone, cap and rotor will have corrosion on the rotor, however a small crack in the distributor cap can be next to impossible to see, replacement is usually best option.

Feb 16, 2012 | 2000 GMC New Sierra 1500

1 Answer

My corolla 2001 the engine light is on test by computer show po446 problem


P0446 Evaporative Emission Control System Vent Control Malfunction
 Vacuum hose cracks, holed blocked, damaged or disconnected (1), (4), (5), (6) and (7)
 Open or short in vapor pressure sensor circuit
Vapor pressure sensor
 Open or short in VSV circuit for vapor pressure sensor
 VSV for pressure switching valve for vapor pressure sensor
 Charcoal canister cracked, hole or damaged
 Fuel tank over fill check valve cracked damaged
 ECM

Aug 30, 2011 | Toyota Corolla Cars & Trucks

1 Answer

I have codes po441,p0450 on my 1997 lexus es 300 can u help and where are they


P0441 = Evaporative Emission Control System Incorrect Purge Flow.
Trouble Area(s)
Open or short in VSV circuit for VAP.
Open or short in VSV circuit for vapor pressure sensor.
Open or short in vapor pressure sensor.
VSV for EVAP.
VSV for vapor pressure sensor.
Vapor pressure sensor.
Vacuum hose cracks, holed blocked, damaged or disconnected.
Charcoal canister cracked, holed or damaged.
P0450 = Evaporative Emission Control System Pressure Sensor Malfunction.
Trouble Area(s)
Open or short in vapor pressure sensor circuit.
Vapor pressure sensor.
ECM.

Jul 29, 2011 | Lexus ES 300 Cars & Trucks

1 Answer

Crack position sensor where is at


There is NO SUCH Sensor as a crack position sensor.
What or where is your Problem? There IS a THROTTLE POSITION SENSOR

Sep 04, 2009 | 2005 Nissan Altima

1 Answer

Saturn sc1 starting


check coolant temp sensor located at driver side end of cyl head. remove sensor and check or cracks. also check connector for corrosion. if cracked, go to dealer for replacment. they eill sell you a new designed metal sensor to replace your cracked plastic one. dont buy aftermarket, they will not be accurate. cracked sensor will cause eng. to run rich. may start ok cold but not when hot.

Oct 19, 2008 | 1998 Saturn SC

Not finding what you are looking for?
2000 Hyundai Accent Logo

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...