Question about 2003 Hyundai Tiburon

1 Answer

How many bolt studs hold the head to the 2.0 liter engine.. 2003 hyundai tiburon.. Also, my 10MM allenhead doesn't seem to bite enough on the bolt.. do you recommend anything to help get it off without stripping them out. Also, last question, how many bolts hold the transmission on to the engine. Just want to make I have them all out when I goto pull the motor?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,102 Answers

Hi their should be 10 bolts holding the head on and the tool you need is an inverted torque socket these are needed to undo the head bolts using an allen key would just thread the head and would mean drilling the head bolts out which is a night mare, so dont use allen keys as they will not be strong enough to undo the head bolts without threading the head bolts.
as for the gearbox as long as you have undone the 2 at the top and the ones either side and the bottom bolt you should then be able to remove the gear box from the engine, the problem with your car is the gear box has not got much room to come away from the engine far enough to allow you to get it out, you may need to undo the engine mountin bolts to allow you to have a bit extra room you may also need an engine hoist to support the engine whilst removing the box, you may get away without one but it will be difficult.

make sure you have removed the drive shafts from the gear box and also the starter motor and make sure the speedo drive is undone and also the electrics for the reverse light if this is located at the top of the gear box.


Posted on May 09, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I adjust the tension on the alternator belt for my 2003 Hyundai Tiburon?


Adjusting alternator belt tension - bolt & pivot bracket design ...

? 13:06
https://www.youtube.com/watch?v=8JN0RtZk_2Y
Nov 26, 2012 - Uploaded by backyardmech
Releasing tension on the alternator belt to remove the alternator- 4 cylinder Honda in this video. ... How to ...

How To Install replace Alternator Belt 1999-06 Hyundai ...

? 4:51
https://www.youtube.com/watch?v=6IWgXTijclo
May 15, 2013 - Uploaded by 1A Auto Parts
How To Install replace Alternator Belt 1999-06 Hyundai Elantra 2.0L .... Adjusting alternator belt tension ...

Dec 21, 2015 | 2003 Hyundai Tiburon

1 Answer

Need timing belt diagram for a 2003 tiburon gt v6 2.7 liter


The timing belt diagrams are listed in detail with figures and procedure to remove them.

REPLACING TIMING BELT ON A 2003 HYUNDAI TIBURON 2.7L V6

1. Remove passenger side headlight via the 3 10mm screws holding it in place and disconnect the turn signal and main harness

2. Remove passenger side tire

3. Remove the splash guard via 2 10mm screws at the top of the guard

4. Remove the 2 17mm bolts and 2 17mm nuts from motor mount bar

5. You may have to separate the mount bar from the motor via either a chisel or flathead screwdriver and a hammer ( support engine via a jack and a piece of plywood under oil pan )

6. Use a 3/8 ratchet ( or a long breaker bar would work better ) to remove the serpentine belt ( remember the route ). Disconnect the power steering hose from the pump and secure back with a zip tie. Remove the power steering pulley with a pry bar and 19mm socket.

tinualbinale_2.gif
7. Hand turn the crankshaft via a 22mm socket to TDC ( top dead center, marked on lower timing belt cover )

8. Remove the serpentine belt tensioner via 2 12mm bolts on each side

9. Remove the upper timing belt cover via 7 10mm screws

10. Remove crankshaft pulley ( 22mm ) with an air impact gun ( an electric one will work too )

11. Remove lower timing belt cover via 4 more 10mm screws



tinualbinale_3.gif

12. Remove the motor mount from the block via 3 14mm bolts and 2 12mm bolts ( there is a 12mm holding the oil dipstick bracket towards the front of the car )

13. Remove the auto tensioner via 2 12mm bolts

tinualbinale_4.gif

14. Remove the timing belt
tinualbinale_5.gif

15. Make sure your timing markings are correct...

There is one marking on each cam gear and on the heads ( head markings are small, look closely...try wiping the edge of the head down with a rag and some brake cleaner to bring it out more ) They are also pictured in last pic.

When the crankshaft is in the TDC position, the cam gear markings should both line up at the same time with the head markings

Adjust if necessary, use a 17mm socket to turn cam gears to correct position

16. Install new timing belt ( as you install it, make sure to keep a little tension on the belt as you route it )

17. Install new auto tensioner and pull pin

18. Install just the lower timing belt cover

19. Install the crankshaft pulley

20. Hand turn the crankshaft atleast 5 times to verify the timing markings are lining up properly ( all should line up at the same time when the crankshaft pulley mark is in the TDC position )

21. Remove crankshaft pulley

22. Remove lower timing belt cover

23. Reverse steps 12 - 1

You can refer the videos below for further assistance.Your valuable feedback would be appreciated.Thanks for choosing Fixya.


Jun 10, 2011 | Hyundai Tiburon Cars & Trucks

1 Answer

Trying to replace my radiator in an 03 hyundai tiberon i have all the hoses disconected but the radiator still wont come out


it is still bolted to the a/c condensor in front of it. it may only have two 10mm bolts then slip out of some slots at bottom of radiator.

Jun 05, 2011 | 2003 Hyundai Tiburon

1 Answer

Does anyone know the head bolt sequence and torque numbers for a 1997 hyundai tiburon fx 2.0 model?


The Sequence is as follows:

<----Camshaft Sprocket
8 - 6 - 1 - 3 - 9
10 - 4 - 2 - 5 - 7

Tighten the 10mm bolts to 22ftlbs as you get to them in the sequence and the 12mm bolts to 26ftlbs.

Then go around the sequence again tightening every bolt an additional bolt 60 degrees.

Once again go around the sequence again tightening every bolt an additional bolt 60 degrees.

And you should be done.

Dec 20, 2010 | Hyundai Tiburon Cars & Trucks

1 Answer

How to change thermostat on a 2002 Pontiac Montana


I believe the Montana has a 3.4 Liter V6 Engine.
This thermostat is located under the exhaust "crossover" pipe that runs between both the front and rear cylinder heads. Divers side.
Remove the heat shields (10mm bolts) and then the nuts on the exhaust studs. (6 total)
Two bolts hold the T stat housing to the intake.

Feb 23, 2010 | 2002 Pontiac Montana

1 Answer

How do i change the spark plugs


if its a four cyl remove upper coveron top af engine has 6 10mm head bolts pull up the wires to find plugs-caution dont chang plugs without doing wires,the newer version has coil on plug just remove coil pack,should have four with 10mm bolt holding them on,remove bolt and pull up on coil pack

Oct 08, 2009 | 2006 Hyundai Tiburon

1 Answer

Location of the Purge Control Valve for 2003 Hyundai Tiburon


There were two different engines which were installed in the 2003 Tiberon... the 2.0 liter 4 cylinder:
22c99c7.jpg

And the 2.7 Liter V6:
cb31feb.jpg

Jun 06, 2009 | 2003 Hyundai Tiburon

2 Answers

Nology hot wires and Nology silver spark plugs


It is not possible to use Nologi non resistor silver spark plugs together with Nologi Hot wires on my Tiburon 2003. I guess it goes for all Tiburon from 2002 to 2006 with the 1,6 liter DOHC Alpha Engine. But I am still working on it and if I get anything to solve this problem I will be back to tell.

Mar 25, 2009 | 2003 Hyundai Tiburon

3 Answers

Side light bulb change on hyundai terracan


hi there
the solution is simple,
you only need to undo the screw on top of the side light/indicator. then facing the head light place a flat headed screw driver under the bottom lip of side light. the bottom of the lihgt is on a small push fit stud, use a sponge or cloth to protect your bumper paint work then just apply pressure gently to lever side light out towards you, It will come dont worry, you may then change your bulbs if you wish remove the whole light unit you will see the bottom bolt as soon as you release the side light. to replace just push back into place then replace screw. whole job takes about five minutes

hope this helps kevan hildred

Nov 23, 2008 | 2003 Hyundai Tucson

Not finding what you are looking for?
2003 Hyundai Tiburon Logo

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...