Question about 1999 Dodge Intrepid

1 Answer

Had to take timing belt off ,need to reset

Car wont start

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 155 Answers

Is it a clean crank or a lazy slow crank ?
if clean crank check to see if you get a spark or pulse at the injector
slow and lazy crank
double check the timing again
or check to see if you broke or left the crank angle sensor unplug
good luck

Posted on May 09, 2010

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 102 Answers

SOURCE: timeing belt

replace timing belt and check all pulleys

Posted on May 25, 2009

  • 5 Answers

SOURCE: put a new timing belt on, car still wont start.

hi put the #1 piston up with the camshaft lobe up so the valve will seal the compression in the chamber

Posted on Mar 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine will turn over but wont start


The problem is that you have the timing off and needs to be reset also check the cam and crank censors some of them have to be replaced when you do the timing belt it throws them out. But the timming is still out if it is comming out intake.

Jan 28, 2014 | Mitsubishi Mirage Cars & Trucks

1 Answer

I fouled up the timing on my 1990 Subaru Legacy Wagon. Tried resetting it to the factory specs but it still wont start.


You have not set it to the factory spec, and its probably 180 degrees off. Rotate the crank to top dead center (the mark on the crank toothed pulley, align the cam timing marks, refit the belt THEN release the tensioner. Rotate the engine manually to verify that all the timing marks realign themselves.

Jan 19, 2014 | 1990 Subaru Legacy

2 Answers

Changed water pump now wont start battery is charged


If water pump is run by timing belt, the timing will need be reset prior to start up. Make sure timing is adjusted using the timing marks from factory. Check manual to determine timing mark locations.

Jan 20, 2013 | Pontiac Cars & Trucks

1 Answer

Car wont start


did the engine accidentally get turned on by key when timing belt was off or anything that could have moved crank or cam shafts.did you hook battery back up..never know,is their something you have to do to reset computer after you disconnect battery...

Nov 29, 2012 | 2004 Mitsubishi Galant 2.4

2 Answers

Will car still start if timing belt jump and if it do how will it run


99% of the time your car wont start if timing belt has jumped or broke you will still have spark but wont start

Jan 17, 2011 | Acura Integra Cars & Trucks

1 Answer

I REPLACED TIMING BELT .AND I WANT TO KNOW HOW TO RESET THE TIMING ,SO AS NOT TO DAMAGE TO MOTOR. WHEN I GO TO START IT UP .


If you did not set the gears(pulleys) in the same place or set the marks in the timing belt to the marks in the gears the car wont start. when you do the the job is when you set the timing, not after you done. If you use a cheap timing belt those belts do not have marks, I recommend to get a belt from toyota that has a mark for each cam pulley and another mark for the crank pulley. Toyota doesn't have interference engines, so no matter how bad is your timing the car wont start just spin.

Dec 25, 2010 | 1994 Toyota 4Runner

1 Answer

I replaced the water pump and now it will not start i makes a noise while trying to start sounding like it is floating


MOST TOYOTA ENGINES. BEFORE YOU CAN REMOVE THE WATER PUMP. YOU HAVE TO REMOVE TIMING COVER AND BELT YOU HAVE RESET TIMING BELT TIMING .IF NOT YOUR CAR WONT START.

Jul 28, 2009 | Toyota 4Runner Cars & Trucks

1 Answer

Wont stay running


Could be get the specs and reset the timing. If it contiues then try working on the fuel filter or idle speed.

Apr 11, 2009 | 1993 Mitsubishi Eclipse

1 Answer

HELP...1987 944 wont start afer replacing timing belt


Hi, You need to get your timing belt checked. Dont attempt to start the engine until your timing pullys are reset because if your cam is set wrong it WILL cause valve damage.If it is allready correctly set then i suggest you test the compresion in case damage was caused when belt was fitted. Hope all works out ok 4 you.All the best.Phil

Sep 10, 2008 | 1987 Porsche 944

Not finding what you are looking for?
1999 Dodge Intrepid Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...