Question about 1998 Ford Expedition

1 Answer

Need to replace back gate and trying no to cut

Need to replace back gate and trying no to cut wiring. looking for plug ?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 474 Answers

You will have to get into the rear gate and disconect all wiring one by one and pass them threw the hole where the wires enter the gate.Unfortunetly this may be the only way.

Posted on May 09, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lift gate won't lock


Could be the latch in the gate. Could be wiring, they tend to break at the top of the gate where the wires goes into the body. Also could be the body control module.

May 06, 2016 | Buick Rendezvous Cars & Trucks

2 Answers

Why liftgate acuator clicking when lift gate is open


I would bet on the liftgate module (LGM) It controls all that stuff back there,wiper,defrost,gate ajar light,gate lock and unlock ect. Might try wiggleing the wiring boot where the wires go from the body to the gate,if it changes anything,bet on a broken wire inside that boot.
If not the LGM is my first thought.

Feb 15, 2015 | 2004 GMC Envoy

1 Answer

2005 chevy trailblazer liftgate ...gate tries to keep opening ...hear the motor


you have a cut or bad connection where the wires come from the inside of car and causing a short,so you might have to open the outer cover surrounding the wires,.,,,,,,adrian

Dec 28, 2014 | 2005 Chevrolet TrailBlazer

1 Answer

Need a wiring diagram for a 1997 Nissan quest xe fuel pump assembly it has 4 wires and my not so smart brother in law tried to change fuel pump abd instead of disconnecting the plug he cut the wires so I...


Usually, replacement pump will come with wiring instructions. If dumbo lost them, might go to friendly parts store and ask to look at chart in another one, or simply look at wiring diagram in your shop manual.

Dec 15, 2014 | Cars & Trucks

1 Answer

Left turn signal cuts fuse but the right works on our 89 gmc truck


There's a short in the wire harness for the left side..Look at the wires near the tail gate where the plug for trailer wires would connect. You might have a bulb with a short to ground too.

Jan 28, 2014 | Cars & Trucks

1 Answer

Renault Clio Phase 2 - tailgate. Anyone know if


tail gates are completely assembled before fitting on the assembly line and that includes the wiring harness for the gate . So I would expect a harness connector either in side the gate or in a body panel trim close to the gate.

Oct 12, 2013 | 2000 Renault 181

1 Answer

Gate light on even when gate is closed


Open gate and find where the wiring enters the gate (bottom of door) pull back the rubber insulator and check for broken wires or wires touching each other.

Mar 05, 2013 | 2010 Jeep Liberty

1 Answer

Engine has no power under 3000 rpm


have a look at the EGR valve if its stuck open you loos all the turbo boost till the EGR valve closes
it could also be the turbo gate valve (wast gate) sticking open so the turbo cant cut in till its screeming then the gate shuts and the old girl picks up her skirts and go's,,, you may get away with just blanking off the EGR valves to try them out but the turbo is a different mater,,,

Dec 06, 2009 | 1992 Toyota Pickup

1 Answer

1994 Jeep Grand cherokee rear lift gate


Well My 94 Jeep Grand Cherokee had the same problem and we had to just cut into the lift gate panel from the inside. It required cutting plastic but with a 94 looks arent everything and a working lift gate was worth it. But then we pealed back this black plastic mat under the panel and lifted up on the release bar(verticle bar that lifts the latch) and once we got it open we adjusted a little clamp that had slipped. Dont adjust it too much or when u lock it it wont lock! But sorry i dont know the name of the parts. But then u can screw the panel back in and it wont look to bad besides some cuts.

Jun 09, 2009 | 1994 Jeep Grand Cherokee

2 Answers

1995 jeep grand cherokee,i want to bypass the factory alarm.


the security module is located behind the dash trim at the glove box. remove glove box door, and top crash pad, and trim around glove box door. The security module is mounted behind the trim panel. Unplug it and it bypassed.

Jan 31, 2009 | 1995 Jeep Grand Cherokee

Not finding what you are looking for?
1998 Ford Expedition Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...