Question about 2004 Ford Taurus

1 Answer

How do I remove the AC compressor? - 2004 Ford Taurus

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

You really need to go to an a/c shop and get them to remove the freon. then you will need some special tools to remove the a/c lines, you will need to remove the serpentine belt and the power steering pump so you can lift a/c compressor out of car.

Posted on May 31, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can we fix the heater and defrost in a 2001 Isuzu Rodeo LS without the AC compressor


You may be able to remove compressor and purchase a pulley with an arm that atttaches to the block in place of compressor. Or remove compressor altogether and install a shorter serpentine belt. Hope this has been of some help.

Nov 14, 2013 | 2001 Isuzu Rodeo

1 Answer

How to take out air condition compreser out of a2001 mercury sable


have dealership discharge airconditioning system.you need to disconnect refrigerant lines going to the AC compressor you probably need refrigerant lines disconnect tools to remove disconnect refrigerant lines.you need to remove drive belt.and safely raise support vechicle remove tire or wheel work from under vechicle you have to loosen AC COMPRESSOR bolts then remove AC COMPRESSOR.be sure pour old refrigerant in a measuring cup so you can pour same amount new oil in the new compressor.add couple ounces if old AC COMPRESSOR dry.

Feb 11, 2013 | 2001 Ford Taurus

2 Answers

How to replace ac compressor to a 2003 f 250 5.4


An Air-Conditioner loses its fizz with passage of time due to constant usage or wear and tear.Just dial to Dailfix they will help you with all things.

AC Repairs Services in Hyderabad Dialfix

Jul 15, 2011 | Ford F-250 Cars & Trucks

2 Answers

How do you remove the air compressor. i am going to use a bypass pulley.


You have a 16 year old vehicle
How long are you going to keep it?
I wouldn't bypass the A/C Compressor
What will that do?
Why spend money,you don't have to?

Nov 08, 2010 | 1994 Oldsmobile Cutlass Supreme

1 Answer

I need a diagram on how to remove a ac compressor on a 1996 lincoln mark VII


There's not really a diagram for the actual removal and installation. A good repair manual might list steps like these: First, your system needs to be purged of the freon. Next, unplug the AC clutch/pulley assembly at the front of the compressor. Remove the belt, then the AC lines on the compressor (usually in the back), then unbolt the AC from any mounting bracket(s) and remove. To avoid having to press on and off the clutch/pulley assembly you might want to make sure you're buying a complete compressor assembly. Read and follow those directions concerning oil for the compressor. After installing the new AC, reconnect the lines with new "O" rings. Most if not all compressor manufacturers will not honor any warranty unless you change out your orifice tube (also called an expansion valve) and accumulator (aka the dryer) at the same time. Recharge the system with the appropriate amount and type of freon, most likely R-134a.

Oct 05, 2010 | 1996 Lincoln Mark VIII

1 Answer

Would like to know how to intall an air condition compressor


Firstly de gas the a/c system then remove a/c belt then remove the 2 a/ c pipes to the compressor then disconnect the ac clutch wiring remove the bolts holding the compressor to the cyl block fit new compressor replace the ac pipe orings Then refit the ac pipes reconnect ac clutch wiring refit belt. Then regas the system addind uv dye and comressor oil

Oct 04, 2010 | 2001 Pontiac Grand Am SE

1 Answer

The air coditioner quit..makes loud noise. how do I remove the compressor ?


you will need to recover 1st the freon in the vehicle , once that is done, you need to remove the drive belt to free up the AC pulley. once that is done, you will then need to remove the AC line manifold from the back of the AC Compressor. The AC manifold needs to be covered by a ZIP LOCK bag to not allow any moistutre in it. Remove bolts that hold down the AC Compressor and the electrical harness attacked to it.

Aug 27, 2010 | 1993 Oldsmobile Cutlass Supreme

3 Answers

Ac compressor clutch is making a noise is the clutch is replaceable without replacing compressor


I had the same issue with my 2006. I thought the compressor clutch bearings were faulty. After further research, the rattling noise was actually coming from the serpentine belt tensioner. Easy repair!
Hope this helps.

Jan 28, 2010 | 2006 Jeep Liberty

1 Answer

01 Accent AC problems


1. Discharge/Recover the refrigerant. 2. Remove the tension bolt. a4c16f6.jpg 3. Remove the V-belt and magnetic clutch wire harness connector.
d768bec.jpg
4. Remove the suction hose and discharge hose from the compressor. 5. Remove the 4 mounting bolts on the compressor.
3bb9fac.jpg 6. Remove the compressor downwards.

INSTALLATION IN REVERSE ORDER
1. Tighten the 4 compressor mounting bolts.
2. Connect the suction hose and discharge hose to the compressor. 3. Connect the V belt. 4. Adjust the V belt tension.5. Reconnect the magnetic clutch wire harness connector.

Jun 04, 2009 | 2001 Hyundai Accent

1 Answer

Ac repair procedure 2003 ford taurus


recover r134. remove cooling fan and shroud assembly. Remove surp belt. Unplug compressor connector. From under car. Remove ac manifold retaining bolt. Remove O2 sensor from exhaust for clearance. Unbolt compressor and remove (some of the bolts will have to be inserted into the new compressor prior to installation. Reverse all steps and evacuate and recharge system.

Jul 08, 2008 | 2003 Ford Taurus

Not finding what you are looking for?
2004 Ford Taurus Logo

357 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...