Question about 1988 Ford Crown Victoria

1 Answer

Cannot find )_*(@#%@#%& location of AC Compressor RELAY on 1988 FORD CROWN VICTORIA LTD

Posted by on

  • 1 more comment 
  • monte542 May 09, 2010



    Where? I dont see it. Is it cylindar to left of reservoir?





  • monte542 May 09, 2010

    still need a little help here

  • monte542 May 09, 2010

    I am such a dunce when it comes to this. Here they are right where you said they were.. THanks!


×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Expert
  • 4,070 Answers

Hi! Please try this. Open the hood, you'll see the relay on the fender of the driver's side next to the windshield washer reservoir. Pull out the relay and check if its blown. If it is, replace it to get it back to normal working. HOpe this helps and have a good one!

Posted on May 09, 2010

  • dj_relly999
    dj_relly999 May 09, 2010

    Have you seen any relay boxes on the sides of the fender? You will need to pull out the cover to have an access.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the pcv valve located on a 1991 ford crown victoria?


its located at the back of the engine near the firewall. it has a large hose connected to it(3/8") if I remember right. it is attached to top of the PCV valve. pull the hose off then you can pull the valve out of the rubber grommet that holds it into the engine.

Sep 23, 2014 | 1991 Ford LTD Crown Victoria

1 Answer

My 1998 Ford Crown Victoria was running just fine when parked Thursday evening. Friday morning, the air condiioner compressor will not come on. The fan runs--everything else runs fine.


Hopfully it's a fuse, if not a fuse then check relay, if not the relay, then check the clutch on the coompressor, while the motor is off, check to see if the AC compressor clutch will turn freely, if not, replace the compressor.

Aug 10, 2009 | 1998 Ford Crown Victoria

2 Answers

My horn doesn't work for my 1988 Crown Victoria


check fuse and also check the wire going to the horn and check the inside of the horn too and check the ground

Jul 04, 2009 | 1988 Ford Crown Victoria

4 Answers

1988 Ford Crown Vic Lost Cruise Control


Although I don't think the cruise is an issue for safety, reach in under hood , or in grille area and find your horn(s) and just pull the connector off them temporarily, so they won't blow & put fuse back in and see if cruise starts to work again. It's not unusual for circuits to be labeled wrong or not at all in fuse panels. Then you can turn your attention to horn problem.

Jun 27, 2009 | 1988 Ford Crown Victoria

1 Answer

Fuel pump is not pumping on my ford ltd crown victoria. i need a fuse diagram so i can see if it is just the fuse or if i need to replace the pump.


There is both a fuse and a relay for the fuel pumps electrical system. The image below of the Power Distribution Box is located in the engine compartment.

Fuse/Relay Location: 5
Fuse Amp Rating: 20 Amp Mini Fuse
Power Distribution Box Description: Fuel pump

Fuse/Relay Location: 203
Fuse Amp Rating: 1/2 ISO
Power Distribution Box Description: Fuel pump relay

eec14ad.jpg

Apr 14, 2009 | 2003 Ford Crown Victoria

1 Answer

No fuel


Check the inertia fuel switch located near the floorboard. It will have a button that you can press to reset the switch.

Jan 30, 2009 | 1988 Ford Crown Victoria

1 Answer

1987 Ford Crown Victoria LTD


If it was an old police vehicle it has probably got an ignition kill switch located somewhere. This will have to be removed. And the wiring put back to factory standards. If not an old police car you are not getting voltage to the starter which is a bad relay. Do you get a clicking sound when you try to start? If yes, have someone keep hitting the start and listen and look for a relay under the hood.

Sep 26, 2008 | 1987 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...