Question about 2002 Pontiac Montana

Open Question

I have a 2000 Montana. The traction control light is on and cruise control doesn't work. Could that be the break switch?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 51 Answers

SOURCE: cruise control

The cruise control should have a fuse in the interior fuse block, and a larger fuse and/or relay under hood in the relay center block. Test them with an automotive test light (You can purchase these for anywhere from $5.00 to $50.00 depending on the quality you want and the place of purchase).

If you find a bad fuse or primary fuse, obviously those need to be replaced. Relays can't be tested readily using the light. Unfortunately the simplest method for finding out if a relay is bad is to replace it. The relay for that cruise runs between $15.00 to $20.00 depending where you purchase.

Let me know how it goes and we'll see what more we can do!

Posted on Feb 07, 2009

  • 14036 Answers

SOURCE: 1999 oldsmobile alero the traction and cruise not working

use a scanner to check the abs system . most of the time the abs brakes and traction control system work together. your cruise control . unit has a servo motor .in front right fender well. check the fuse and relay also the cruise control brake release switch. and the brake light switch.if all is good you have a cruise control module problems. dealer ship job.

Posted on Apr 02, 2009

  • 2 Answers

SOURCE: 2000 montana brakes shutter and the abs light and

i had the same problem on my 2000 montana, used a scanner to check for abs code and found right front sensor throwing code, checked sensor and found ok, checked harness from sensor to connection under hood and found wiring circut at the plastic clip where harness hooks to sensor was bad, replaced harness from connector to sensor and problem went away

Posted on Jun 17, 2009

  • 1 Answer

SOURCE: auto traction and cruise control problems

Just replaced both front bearings on my 2000 olds silhouette, the traction control light / ABS light is still on. What do i do?

Posted on Sep 04, 2009

  • 3 Answers

SOURCE: Handbrake and Traction control warning lights illuminated amber

Had DTC warning light come on on my 120i (2005 reg). Without prompting dealer contacted BMW who agreed to pay for part and half the labour as it seems to be a common problem for 04-06 models.

Posted on Sep 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cruise control Does Not Work, Service Electrical System always comes on, Traction Control Light comes On


make sure 3rd brake light works, most likely you have a code in the EBCM (antilock brakes), some codes disable the cruise control, possible vehicle or output speed sensor or wheel speed sensor.

Apr 08, 2014 | 2001 Cadillac Seville

1 Answer

My cruise control lights and everything work, but it wont set speed and hold that speed, or anything. all fuses are good


Suggest 2 basic checks:
1. check engine light on? Some severe codes may also disable cruise control (and traction control, etc.).
2. make sure your break lights aren't on. The switch on the break pedal controls the break lights, AND cancels cruise.

Oct 09, 2013 | 2006 Dodge Ram 1500

1 Answer

My Cadillac sts 2005 4.6 cruise control doesn't


Cadillac has a cruise control system that becomes disabled when there is a fault in either the suspension, abs, traction control, or engine management system. The car needs to be scanned to find the cause

Apr 21, 2013 | Cars & Trucks

1 Answer

My 99 grand am anti break and traction warning lights come on for no reason and kicks off my cruise...doesn't matter if I have traction or not...any ideas?


Yes . Most likely one or more of the wheel speed sensors is faulty and needs to be replaced. If these are faulty the ABS will not work and you will get the ABS warning. These should be checked first.
Then the anti lock braking system pump should be checked to ensure it is operating. If it is not you will get the ABS warning.

Dec 24, 2012 | Cars & Trucks

1 Answer

Cruise control does not engage


Is the speedo working, TC ABS light on? You need the EBCTM...electronic brake control traction module replaced.

If not, check the fuses for the cruise cct.

Oct 17, 2009 | 2000 Cadillac Catera

1 Answer

Brake lights on 2000 Civic EX w/ cruise control do not work when brake pedal is pressed. I had the same problem 2 years ago and the brake light switch was replaced. Where do I locate the brake light...


The break lite switch is located behind the break pedal and it probably doesn't replaced it is probably just stuck. Its fairly easy to get to .

Aug 14, 2009 | 2000 Honda Civic

1 Answer

2000 Chevy Venture cruise control and lower tail lights not worki


Hi you have a multifunction switch , which is your turn signal arm and windshield wiper and also hazard and break lights , it is time to replace it.

Jun 08, 2009 | 1997 Chevrolet Venture

2 Answers

1999 oldsmobile alero the traction and cruise not working


use a scanner to check the abs system . most of the time the abs brakes and traction control system work together. your cruise control . unit has a servo motor .in front right fender well. check the fuse and relay also the cruise control brake release switch. and the brake light switch.if all is good you have a cruise control module problems. dealer ship job.

Mar 31, 2009 | 1999 Oldsmobile Alero

1 Answer

Auto traction and cruise control problems


Just replaced both front bearings on my 2000 olds silhouette, the traction control light / ABS light is still on. What do i do?

Jul 01, 2008 | 2003 Oldsmobile Silhouette

Not finding what you are looking for?
2002 Pontiac Montana Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...