Question about 1997 Chevrolet Malibu

Open Question

Need removal and replacement of water pump - 1997 Chevrolet Malibu

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to replace a water pump on my plymouth grande voyager se 3.3l


Jack up the passenger side and remove the tire. Remove the splash shield to gain access to the belt and tensioner. Remove the serp belt. Remove the bolts holding the pulley to the water pump. Remove the pulley Remove the bolts holding the water pump to the timing cover. Remove the water pump. Be prepared for the bolts to break. It happens often!

Jul 13, 2013 | Cars & Trucks

1 Answer

I need a chart for the water pump


For water pump replacement i suggest you to check the help link provided below.

click the link below :----

Water pump replacing procedure for all vehicles?

http://technoanswers.blogspot.com/2011/11/water-pump-replacing-procedure-for-all.html
---------

HOW TO REPLACE A WATER PUMP

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-water-pump.html

------------------
How to route Water Pump Belt for 1992 Oldsmobile ?

http://carbeltrouting.blogspot.com/2011/12/how-to-route-water-pump-belt-for-1992.html

---------
How to replace Water Pump on Car ?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-water-pump-on-acura-car.html

---------
How to Remove Water Pump?

http://technoanswers.blogspot.com/2011/12/how-to-remove-water-pump-on-toyota.html

-------
Where is Water Pump located ?

http://technoanswers.blogspot.com/2011/12/where-is-water-pump-located-on-toyota.html

-----------

This will help. Thanks.

Feb 01, 2012 | 1996 Dodge Neon

1 Answer

I need to replace the water pump and put the car back to geather


For water pump replacement i suggest you to check the help link provided below.

click the link below :----

Water pump replacing procedure for all vehicles?

http://technoanswers.blogspot.com/2011/11/water-pump-replacing-procedure-for-all.html
---------

HOW TO REPLACE A WATER PUMP

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-water-pump.html

------------------
How to route Water Pump Belt for 1992 Oldsmobile ?

http://carbeltrouting.blogspot.com/2011/12/how-to-route-water-pump-belt-for-1992.html

---------
How to replace Water Pump on Car ?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-water-pump-on-acura-car.html

---------
How to Remove Water Pump?

http://technoanswers.blogspot.com/2011/12/how-to-remove-water-pump-on-toyota.html

-------
Where is Water Pump located ?

http://technoanswers.blogspot.com/2011/12/where-is-water-pump-located-on-toyota.html

-----------

This will help. Thanks.

Jan 21, 2012 | 1996 Mitsubishi Galant

1 Answer

Need to replace water pump on 2003 ford taurus


For replacing water pump , you also have to remove, accessory belt,timing belt,timing belt cover and other minor components. Removing water pump is not very difficult, but removal of this other components is necessary, then only you can replace water pump. For detailed procedure, click the link below:--- http://technoanswers.blogspot.com/2011/10/water-pump-removal-instructions-for.html -------- This should help.Thanks.Helpmech.

Oct 28, 2011 | 2003 Ford Taurus

1 Answer

Mercedes 1998 c230 water pump replacement


REPLACE WATER ALL YOU NEED TO DO IS DRAIN THE COOLANT SYSTEM.REMOVE THE ENGINE COOLING FAN AND CLUTCH THEN THE FAN SHROUD.REMOVE ENGINE COVER IF EQUIPPED.THEN REMOVE THE ACCESSORY DRIVE BELT.UNBOLT THE POWER STEERING PUMP MOVE IT ASIDE DONT DISCONNECT ANY POWER STEERING PUMP HOSES.DISCONNECT WATER PUMP HOSES, REMOVE BELT PULLEY THEN REMOVE WATER PUMP MOUNTING BOLTS AND WATER PUMP.CLEAN WATER PUMP MATING SURFACE BE CAREFUL DONT SCRATCH PUMP SURFACE. BESURE WHEN YOU INSTALL NEW WATER PUMP USE GASKET SEALANT ON BOTH SIDE OF GASKET TO KEEP IT FROM LEAKING COOLANT.

Sep 26, 2011 | 2007 Mercedes-Benz C230 Sedan

1 Answer

Need instruction for replacing water pump 2004 GMC Envoy 4.2 liter engine.


TO REPLACE WATER PUMP.FIRST YOU HAVE TO DRAIN THE COOLANT SYSTEM. REMOVE AIR INTAKE DUCT AND RESONATOR. REMOVE THE RADIATOR SHROUD AND FAN CLUTCH ASSEMBLY REMOVE THE DRIVE BELT. REMOVE WATER PUMP PULLEY.YOU NEED A PIN SPANNER WRENCH OR STRAP WRENCH TO HOLD WATER PUMP PULLEY WHILE LOOSEN WATER PUMP PULLEY BOLTS .YOU CAN BUY STRAP WRENCH OR RENT PIN SPANNER WRENCH AT AUTO ZONE PARTS STORES OR OTHER STORES HAS TOOLS CAN BE RENT. ONCE WATER PUMP PULLEY REMOVED. REMOVE THE WATER PUMP MOUNTING BOLTS. REMOVE WATER PUMP. IF WATER PUMP STUCK YOU CAN TAP WITH SOFT FACE HAMMER OR A LONG PIECE OF ROUND WOOD.WHEN WATER REMOVED.YOU NEED TO CLEAN THE SEALING SURFACE CAREFUL DONT SCRATCH SEALING SURFACE. YOU CAN BUY CAN OF SPRAY GASKET REMOVER.CLEAN SURFACE GOOD THEN WIPE WITH LACQUER THINNER OR ACETONE.THEN GET WATER PUMP NEW GASKET MATCH HOLES UP WITH GASKET TO WATER PUMP. ONCE HOLES MATCH UP APPLY RTV SEALANT ON BOTH SIDES WATER PUMP GASKET. THEN PUT GASKET ON WATER PUMP THEN INSTALL WATER PUMP TO VECHICLE.TORQUE WATER PUMP BOLTS TO 89 INCH LBS .TIGHTEN WATER PUMP PULLEY BOLTS TO 18 FT LBS THEN PUT EVERY THING BACK VISA VERSA.

Aug 26, 2011 | GMC Envoy XL Cars & Trucks

1 Answer

How do i replace the water pump on a 1997 rodeo v6?


YOU HAVE TO REMOVE TIMING BELT AND IDLER PULLEY.YOU NEED TO REPLACE TIMING BELT WHEN YOU REPLACE WATER PUMP.TO REPLACE WATER PUMP. DRAIN COOLANT SYSTEM.REMOVE UPPER RADIATOR HOSE.REMOVE TIMING BELT AND IDLER PULLEY.UNBOLT AND REMOVE THE WATER PUMP.CLEAN ANY GASKET MATERIAL OR SEALANT RESIDUE FROM THE WATER PUMP MATING SEALING SURFACES.WHEN INSTALLING NEW WATER PUMP BESURE TO USE A SEALANT ON BOTH SIDES OF WATER PUMP GASKET TO KEEP IT FROM LEAKING COOLANT.TORQUE WATER PUMP BOLTS TO 13 FT LBS IN A TWO STEP CRISSCROSS SEQUENCE.INSTALL THE IDLER PULLEY.TIGHTEN THE MOUNTING BOLT TO 31 FT LBS.INSTALL AND TENSION THE TIMING BELT.INSTALL THE UPPER RADIATOR HOSE.REFILL BLEED THE COOLANT SYSTEM.

Feb 19, 2011 | 1997 Isuzu Rodeo

1 Answer

Need to replace the water pump on a 1992 gmc pick-up need diagram of how to replace do I need to pull the fan cluch and radiator to get to it???


hi,first off you have to remove the acc. drive belts, ac,alt.,pwr str belt etc.but loosen up the 4 bolts that hold the fan to the water pump.then remove any brackets 4 bolts hold the water pump in place and remove water hoses before removing pump bolts. clean and replace gaskets and pump reinstall all parts and added coolant .also you may want to replace thermostat.

Oct 23, 2009 | 1992 GMC Sierra K1500

1 Answer

How to change water pump (1997 sonoma)


The text below is from the GM Service manual 4.3L V6 Engine
Water Pump Replacement (4.3L)
Removal Procedure
Drain the cooling system. Refer to Draining and Filling Cooling System .
Loosen the water pump pulley bolts.
Remove the cooling fan and clutch assembly.

Tools Required
J 46406 Fan Clutch Wrench

Removal Procedure
Remove the upper fan shroud.
Remove the fan clutch from the water pump in a counterclockwise direction using the J 46406 .
Remove the fan clutch assembly.
Remove the drive belt. Refer to Drive Belt Replacement Remove the water pump pulley mounting bolts.
Remove the water pump pulley.
Remove the radiator outlet hose clamp from the water pump.
Remove radiator outlet hose from the water pump.
Remove the water pump mounting bolts.
Remove the water pump from the engine.
Remove the water pump gaskets.
Clean the water pump gasket mating surfaces.
Installation Procedure
Install the water pump gaskets.
Install the water pump to the engine.
Apply a sealer (GM P/N 12346004) to the bolt threads.
Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
Install the water pump mounting bolts.
Tighten
Tighten the mounting bolts to 41 N·m (30 lb ft).
Install the radiator outlet hose to the water pump.
Install the water pump pulley.
Install the water pump pulley bolts.
Tighten
Tighten the water pump pulley bolts to 25 N·m (18 lb ft).
Install the drive belt. Refer to Drive Belt Replacement in Engine Mechanical - 4.3L.
Install the fan clutch assembly.
Fill the radiator cooling system. Refer to Draining and Filling Cooling System .
Inspect the cooling system for leaks.

Oct 01, 2009 | 1997 GMC Sonoma

2 Answers

Do I need any special tools? How Hard is it?water pump 2002 aztek


take everything around your water pump of and use a metric 10 box end wrench

Apr 30, 2009 | 2002 Pontiac Aztek

Not finding what you are looking for?
1997 Chevrolet Malibu Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...