Question about 1992 Mazda B-Series

1 Answer

'96 Mazda B2300 Trans. Problems

Alright, I just replaced the clutch and slave cylander because my truck ( '96 Mazda 2300) would not go into gear. Well, I got to drive it for about a week but it started doing it again, it won't do it everytime but for the most part reverse or 1st gear won't engage. Last time it was only 1st and reverse but this time around I've noticed 2nd and 3rd are starting to get stubborn too. 4th and Overdrive are still ok.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 196 Answers

Check the fluid level my just need fluid in the gearbox

Posted on May 09, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My slave cylndr is out my truck is stuck in reverce how do i get it out to drive it home to fix it


if no clutch and you get it in a gear to drive what do you think will happen when you have to stop. you need to be towed

Aug 15, 2015 | Mazda Cars & Trucks

1 Answer

96 ford ranger mazda b 2300 with 2.3 liter engine 5 speed when driving down the road and shifting gears the rpms rise before it goes. Into gear


Sounds to me like the clutch is worn and slipping. If there is chatter when engaging the clutch, it may also be a worn throwout bearing.

May 10, 2015 | Ford Cars & Trucks

1 Answer

I put a slave cylinder in my 97 mazda but the clutch will still not disengage but it moves the fingers on the clutch


Clutch disk could be in backwards.
Slave cylinder may have an adjustment that needs to be extended.
Pilot bearing could be bad and keeps the pilot shaft spinning. (simulates clutch not disengaging)
Pivot pin of the throw out arm could be worn down.

May 13, 2014 | 2005 Mazda B2300 Regular

1 Answer

My Mazda b2300 2wd , there is no clutch ? If I start it in gear with the clutch pressed in, it takes off. I have to power shift it from that point on. Is it really my clutch or is the master and sl


fix the leak, fix the leak, fix the leak....A leak in a hydraulic system causes too much pressure loss.
Be sure you bleed the system at the slave cylinder. If that doesnl't give you a normal clutch, then fix the leak.

Nov 15, 2012 | Mazda B2300 Cars & Trucks

1 Answer

2002 saturn vue, manual shifting problems


You have a slave cylinder for this trans. Pump the clutch pedal 25 times with the engine OFF. Then start it and try shifting it into each gear while parked. If this make it work your slave cylinder needs to be replaced

May 15, 2010 | 2002 Saturn VUE

3 Answers

Pedal is going to the floor and hard to put into gear.


you mean the clutch pedal? when asking questions it helps to tell which engine, trans, 4wd, 2wd, which pedal, what you have checked, ect......... ck the clutch fluid level ,you will need to replace the clutch master and slave cylinder, the trans will have to come out.

Oct 19, 2009 | 2007 Mazda B3000

5 Answers

Stuck clutch pedal on a Mazda B series truck


Replace both clutch slave and master cylinders, and bleed well. I've also had this happen.

Jul 11, 2009 | 1988 Mazda B2200

1 Answer

My 96 chevy cavalier ,has a standard tranny , all the sudden it will not go into reverse , but it goes into drive.


will it go in with engine not running? if so look at slave or clutch master to be bad or clutch needs replacement,,,if it will not go into gear with engine not running,repair trans. or replace trans.

Jul 06, 2009 | Chevrolet Cavalier Cars & Trucks

Not finding what you are looking for?
1992 Mazda B-Series Logo

Related Topics:

301 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...