Question about 1999 GMC Safari

1 Answer

Only on long drives the transmission bangs from first to second gear.All other shifting is good,short trips and in cool temps its always ok.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 524 Answers

This mostly has to do with valve bodys being worn out or shot.

Posted on May 09, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2000 Buick Century 69k mi. automatic trans. hard thud changing from 1st to 2nd gear, whining noise between gears


No idea without a drive so please ask a local mechanic to have a look for you

Dec 19, 2013 | Cars & Trucks

1 Answer

98 voyager 3.3 auto trans wont chande gears --seems to be staying in second gear --- hard to move from standstill --- engine temp light came on --- once transmission cools down it works ok til gets h


If you have been driving it, with it over heating as well as
low on fluid your pretty much done & will need a rebuild

If you just drove 10 miles-- then possibly you could have it
diagnosed & find a less costly solution- such as bad solenoids,
but I doubt it

Dec 12, 2012 | 1998 Chrysler Town & Country

1 Answer

6 months ago driving on interstate, working the truck hard trans temp @ 200 shifts into netural finally goes into high. Clear codes, finish my trip. Sense them short trips it will stop at light and shift...


P0700 juist means that the transmission has had a fault occur and the then a fault code was set for that fault, the P1711 is the actual fault. Read about this fault code at the link, there is a bulletin on this for the faults.

Jun 21, 2017 | Chevrolet C2500 Cars & Trucks

1 Answer

I hear a slight 'bang' when the automatic transmission shifts down. It doesn't happen often, only occasionally, especially when it has to shift quickly. I drive a Renault Laguna Initiale 3 litter engine 6V...


Check fluid level and condition, replace or top off as needed. If fluid is full and in good condition then its either shift solenoid or the gear itself. If fluid is a-ok take it to a transmission repair shop.

Aug 02, 2010 | Renault 181 Cars & Trucks

1 Answer

Shifting from park to drive transmission bangs into third gear and will not shift up or down from third


has the transmission been test for electronic fault codes? do this as a 1st step, this may be a problem with shift solenoids or the Transmission Control Module, or TCM for short.

Jan 17, 2010 | Mazda MAZDA6 Cars & Trucks

3 Answers

700 r4 shift hard


The u-joints could cause the banging when you put it in gear. You might want to check the kick down cable. If it's out of ajustment it can cause the hard shift. The transmission thinks the motor is going faster then what it is and will shift harder. Put the car up on jack stand in the rear and put the tranny in neutral.turn the drive shaft back and forth with your hand and see if you hear the clunk or bang you heard when you put it in gear. if not then I would go with the kick down cable being to tightor to short on ajustment. However you want to look at it.

Jul 25, 2009 | 1984 Chevrolet Camaro

1 Answer

1997 Chevrolet 1500 z71 4x4 shifting problem


Check the U-joints at the transfer case.

Feb 24, 2009 | 1997 Chevrolet K1500

Not finding what you are looking for?
1999 GMC Safari Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...