Question about 1991 Dodge Dynasty

1 Answer

How do i change the turn signal bulbs on the front corner lamps... i can reach the bulb sockets but dont have the room to turn them and on the driver side with the way the battery housing sits i cant even get o the socket or bolt that holds the light in

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

Both the front turn signals are quite a mess to get to on this particular car the fastest and most easy way however to do it is to chalk the rear tires, jack the car up, put it on jack stands, then what you have to do is take off the splash guard under the car that protects the engine from water it's about 7 or 8 bolts be careful no to loose them for the splash guard will have to go back on after your done. Once off in the far corner you should have enough room to put your hand up, you might have to feel for it their is a large plastic screw on bolt that holds then both in careful not to pull out the small one feel for the large one on both sides once you get it turn counter clock wise and tug it out, replace bulb with new put light back into fixture, screw back in until it locks into place and your done, place splash guard back on, the whole project took me about 30 minutes with all the tools handy. Only tools you will need are jack stands, chalks, 10MM socket and socket wrench " for the splash guard" flash light, and a pair of rubber gloves if you dont want to get your hands all dirty.

Posted on May 10, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change a front turn light in a 1996 taurus.


Lamps, Parking Front Lamp-Lamp Assembly, Taurus
Removal and Installation
  1. Remove Headlamp (13008) as outlined.
Headlamp Assembly
Removal and Installation
  1. ani_caut.gif WARNING: THE REPLACEABLE HALOGEN HEADLAMP BULB CONTAINS GAS UNDER PRESSURE. THE HALOGEN HEADLAMP BULB MAY SHATTER IF THE GLASS ENVELOPE IS SCRATCHED OR THE HALOGEN HEADLAMP BULB IS DROPPED. HANDLE HALOGEN HEADLAMP BULB CAREFULLY. GRASP HALOGEN HEADLAMP BULB ONLY BY ITS PLASTIC BASE. AVOID TOUCHING GLASS ENVELOPE. KEEP HALOGEN HEADLAMP BULB OUT OF REACH OF CHILDREN.
    Position headlamp switch (11654) and headlamp time delay switch (13736) in the OFF position.
  1. Remove two bolts retaining headlamp (13008) to upper support assembly and loosen pinch bolt. Remove headlamp assembly from vehicle.
  1. Remove park lamp bulb and socket (Sable only) and headlamp bulb and socket from Headlamp Assembly as outlined.


    Headlamp Assembly (Taurus Shown, Sable Similar)


    k24744a.gif
  1. Turn lamp socket and wiring (13410) assembly 1/2 turn counterclockwise and remove from parking lamp (13200) housing.
  1. Remove screw from park/turn signal housing.
  1. Using 1/4 inch drive socket extension and swivel, insert tool through two access holes in upper radiator support. Remove screws from park/turn signal housing.
  1. Remove parking lamp from vehicle.
  1. To install, reverse Removal procedure.


    Front Lamp-Lamp Assembly, Taurus


    k23818a.gif

Nov 19, 2010 | Ford Taurus Cars & Trucks

1 Answer

How to change the front turn signal on a 2001 corvette


For the 2001 Corvette it's simple for replacing it. Using a Sylvania yellow bulb, part# 3157NA LL or 4157NA LL

Reach inside the air intake opening just below the turn signal and push the black friction-fit hose back and down so it is out of your way. With the fingers of one hand, you can press the top of the black plastic duct (air intake) down to make room for your other hand to squeeze into the opening. Reach inside the hole and locate the wiring harness and lamp socket for the turn signal. The harness is on the bottom of the lamp assembly, so that the bulb is essentially sticking upwards into the reflector housing. Turn 1/4 turn and pull wiring harness out of the opening. Change the bulb and reverse the process. Takes about 4 minutes.

Aug 26, 2010 | 2001 Chevrolet Corvette

2 Answers

How do you change the turn signal blub


Hello, I can help you with this. There are 3 different ways to change the bulb. Method 1 If you have skinny arms and small hands, (I can't do it this way but I've seen it done), you can push the brake cooling duct at the front bumper down and back and reach inside and grab the bulb socket from there. Method 2, MANUALLY raise the headlight about halfway up, ( don't use the switch, it will auto-close after 15 minutes and you don't want your hand caught when it lowers), and remove the headlight surround shroud, that will give you enough room to reach the turn signal bulb socket. Method 3, remove the plastic panel underneath the car directly below the turn signal and reach up. Whichever way you decide on just grab the socket and turn clockwise to loosen the socket.

Mar 02, 2010 | 2001 Chevrolet Corvette

2 Answers

How do I change the back turn signal on my 2001 ford taurus


DIY - 5 Minute Turn Signal Bulb Replacement This is very simple to do. First you will need an 8mm socket and wrench to loosen one bolt. Second a good long flat head screwdriver. There are two black metal folded tabs behind the headlight assembly and one 8mm bolt holding it in plae at the center point of the front of the car. Loosen the bolt and remove. Use the screw driver to pull up the metal straps and then slide forward the entire assembly. This will slide easily unless your front bumper has been bumped! That will make it a little difficult to slide if it is out of alignment. If it was never bumped than this should take all of 5 minutes.

Replacing front parking lamp/turn signal/cornering lamp bulbs
  1. Remove headlight / lens assembly per below steps mentioned later

  2. Rotate the bulb socket of the offending bulb counterclockwise and remove from the lamp assembly.

  3. Carefully pull bulb straight out of the socket and push in the new bulb

  4. Install the bulb socket into the headlight assembly by rotating it clockwise

  5. Re-install headlight assembly - hold snugly into place until the brackets line up and retainer pins can be pushed down

To replace headlight bulb:
  1. Make sure headlight switch is turned OFF.

  2. Remove the bolt at the end of the headlamp housing.

  3. Pull the two black tabs with the L shaped bracket toward the back and then up and pull out(Located at the back of the headlamp) to release the headlamp assembly from the vehicle and pull headlamp assembly forward.

  4. Disconnect the electrical connector from the bulb by pulling it.

  5. Remove the bulb socket retaining ring by rotating it counterclockwise.

  6. Remove the bulb from the lamp assembly by pulling straight back.
    Do not twist, as there are alignment slots built into the lamp assembly socket.
    It may take some effort to remove the lamp because it has a rubber o-ring type seal - try a bit of wiggling side-to-side

  7. Insert new bulb into headlight assembly - don't touch the glass - use gloves, paper towel, or similar
    Make sure that the flat surface of the bulb socket is facing upward, and is firmly seated

  8. Re-attach retainer ring by rotating clockwise

  9. Reconnect the electrical harness

  10. Re-install headlight assembly - hold snugly into place until the brackets line up and retainer pins can be pushed down

NOTES
  • Do not touch the glass of the new halogen bulb - the oils in the skin will shorten the life-span of the new bulb, or possibly cause the bulb to explode when first turned on

    If the bulb is accidentally touched, it should be cleaned with rubbing alcohol before being used.

Additional Information1996-2005 Bulb Numbers:
  • FRONT Turn-signal - 3457 AK (amber)
  • Headlamp - 9007 QL (9007LL optional)
  • Tail lamp/brake/turn lamp 3157
  • Tail lamp/brake lamp (wagon) 3157
  • Rear turn lamp (wagon) 3456K
  • Backup lamp 921
  • Backup lamp (wagon) 3156
  • License plate lamp (2) 168
  • High-mount brake lamp (2) 912
  • Rear side marker lamp (wagon) (2) 168

Feb 24, 2010 | 2001 Ford Taurus

1 Answer

How to change parking light bulbs on a 2003 nissan frontier? Do I have to take off the bumber to get to the screw that holds the light component?


2005 Nissan-Datsun Truck Pathfinder 2WD V6-4.0L (VQ40)
REMOVAL AND INSTALLATION OF FRONT TURN SIGNAL/PARKING LAMP

Removal

NOTE: Reach through engine room for bulb replacement access.

  1. Turn the bulb socket counterclockwise to unlock it.
  2. Pull the bulb to remove it from the socket.
Installation
Installation is in the reverse order of removal.

CAUTION: After installing the bulb, be sure to install the bulb socket securely for watertightness.

Dec 23, 2009 | 2005 Nissan Pathfinder

1 Answer

Honda CR-V 1999: how to access front park lamp to change


Don't call me Surely (little joke there) but indeed, the fender/mud guard have to be dealt with. Here's the procedure:
1. If you are changing the bulb on the driver's side, start the engine, turn the steering wheel all the way to the right, and turn off the engine. If you are changing the bulb on the passenger's side, turn the steering wheel to the left.
2. Use a flat-tip screwdriver to remove the fastener from the inner fender.
3. Pull the inner fender cover back.
4. Remove the socket from the headlight assembly by turning it one-quarter turn counterclockwise.
5. To remove the turn signal/side marker bulb, push it in slightly and turn it counterclockwise. To remove the parking light bulb, pull it straight out of its socket.
6. Install the new bulb in the socket.
7. Insert the socket back into the headlight assembly. Turn it clockwise to lock it in place.
8. Test the lights to make sure the new bulb is working.
9. Put the inner fender cover in place. Install the fastener and push on the center until it locks (the center is flush with the head).
Hope this helps you deal with it.

Dec 06, 2009 | 1998 Honda CR-V

1 Answer

Please tell me how to replace a burned out head light, high beam.


To replace the headlamp, turn signal, or parking lamp bulb:This information should be in your owner's manual.
Turn the wheel to access the wheel well.
  1. Remove the fasteners located on the wheel liner. To access the headlamp and the turn signal/parking lamp bulbs.
  2. Reach in behind the wheel well liner and locate the bulb to be changed.
  3. Turn the bulb socket counterclockwise and pull it straight out of the lamp assembly.
  4. Pull the old bulb straight out of the bulb socket.
  5. Push the new bulb straight into the bulb socket until it clicks.
  6. Push the bulb socket straight into the lamp assembly and turn it clockwise to lock it into place.
  7. Reinstall the wheel well liner using fasteners.

Nov 11, 2009 | 2006 Chevrolet HHR

1 Answer

Trying to change the front passenger turn light


Cornering Lamp Removal & Installation To Remove:
  1. Remove the bulb socket from the cornering lamp.
  2. Release the cornering lamp forward retaining tab and pull the front of the lamp away from the fascia.
  3. Remove the cornering lamp rearward retaining stem from the fascia by pulling the lamp forward.
To Install:
  1. Place the cornering lamp rearward retaining stem into the slot in the fascia.
  2. Engage the cornering lamp forward retaining tab into the fascia by pushing in on the front of the lamp.
  3. Install the bulb socket into the cornering lamp.

Jul 10, 2009 | 2004 Chevrolet TrailBlazer

1 Answer

Signal light bulb change/who and where


  1. From under front wheelhouse, remove access cover behind park and turn signal lamp
  2. Through access hole in wheelhouse, rotate park and turn signal socket counterclockwise one quarter turn.
    1. Pull socket from back of lamp.
    2. Pull bulb from socket. INSTALLATION
      1. Align key on bulb base to groove in socket and insert bulb into socket.
      2. Through access hole in wheelhouse, insert socket into back of lamp.
      3. Rotate park and turn signal socket clockwise one quarter turn.
      4. Install access cover and verify lamp operation.
Hope this helps with your prob

Mar 27, 2009 | 1998 Plymouth Voyager

2 Answers

2001 S60 Right Turn Signal Blinks Rapidly compared to Left Signal


Gregg -

I had the same problem. It was a defective lamp socket on the driver's left side, Volvo Part Number 8662985. Costs me $11.24 to replace the lamp socket, which included the bulb. If you've already replaced the bulbs yourself, you will find replacing the socket pretty easy, just use a thin flathead screwdriver to delicately pry off the metal retainer clip which holds the lamp socket in place, as you'll need to reinstall the existing metal retainer clip once you've replaced the lamp socket. Two minute job.

Mar 02, 2009 | 2001 Volvo S60

Not finding what you are looking for?
1991 Dodge Dynasty Logo

185 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...