Question about 2004 Saturn ION

1 Answer

Rear power windows do not work either down or up

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 543 Answers

The most likely cause is the wiring harness in the driver door has broken wires,the master switch for all the windows goes thru the driver door and so do all the wires,the wires get week and break after many door opening and closing and breaks the wires,you will need to remve the door loom in the corner of the door when you open it at the body,the wires are in there,,,,,check that first,you may need to cut open the rubber loom to check it,,,,,if thats not it maybe you got 2 bad window regulators

Posted on May 09, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 gmc envoy Windows fuse


Are all windows not working ? Two separate circuit breakers left & right . Both in rear fuse box . Fuse Block - Rear Beneath the left rear seat
Check for broken wires inside the rubber boot from body to doors.
Do you know about electronic control modules ?
The power window system consists of the following components:
?€¢
Driver door module (DDM)


?€¢
Passenger door module (PDM)


?€¢
Body control module (BCM)


?€¢
LR power window switch


?€¢
RR power window switch


?€¢
Window up and window down relays in each of the rear passenger window switches


?€¢
Window lockout switch


?€¢
Reversible power window motors in each of the doors (circuit breaker protected)


?€¢
LT DOOR CB 25A (System power for left rear window)


?€¢
RT DOOR CB 25A (System power for right rear window)


The power window system will operate anytime the retained accessory power (RAP) system is active or when the ignition switch is in the ACCY or ON position.
The DDM contains 4 power window switches which are integral components. Closing any of the normally open, rocker type switches provides the DDM with a request for power window operation. The switches for the 2 front windows have 3 positions Up, Down and Express Down, while the switches for the rear windows have only 2 positions, Up and Down. Each of these switches and their positions is a direct input into the DDM. Upon receiving a request for power window operation, the DDM, transmits a class 2 message indicating the switch and it's changed position.
The PDM contains a single power window switch that is an integral component. Closing of this normally open, rocker switch provides the PDM with a request for the front passenger power window operation. The switch for the front passenger window has 2 positions Up and Down. Each of these switch positions is a direct input to the PDM.
The 2 rear passenger doors have there own switches. Each of the switches contain a power window up and down relay. A switch activation alone can control the up and down functions of the rear windows. However the BCM, upon receiving a class 2 message from the DDM, can control the set of relays which will activate the rear window motors.

Check

Oct 21, 2016 | 2003 GMC Envoy

2 Answers

Driver door will not work lock or windows


They hooked into wiring they shouldn't have >
Power Window System Components
The power window system consists of the following components:
?€¢
Driver door module (DDM)


?€¢
Passenger door module (PDM)


?€¢
Body control module (BCM)


?€¢
LR power window switch


?€¢
RR power window switch


?€¢
Window up and window down relays in each of the rear passenger window switches


?€¢
Window lockout switch


?€¢
Reversible power window motors in each of the doors (circuit breaker protected)


?€¢
LT DOOR CB 25A (System power for left rear window)


?€¢
RT DOOR CB 25A (System power for right rear window)

Power Window System Controls
The power window system will operate anytime the retained accessory power (RAP) system is active or when the ignition switch is in the ACCY or ON position.
The DDM contains 4 power window switches which are integral components. Closing any of the normally open, rocker type switches provides the DDM with a request for power window operation. The switches for the 2 front windows have 3 positions Up, Down and Express Down, while the switches for the rear windows have only 2 positions, Up and Down. Each of these switches and their positions is a direct input into the DDM. Upon receiving a request for power window operation, the DDM, transmits a class 2 message indicating the switch and it's changed position.
The PDM contains a single power window switch that is an integral component. Closing of this normally open, rocker switch provides the PDM with a request for the front passenger power window operation. The switch for the front passenger window has 2 positions Up and Down. Each of these switch positions is a direct input to the PDM.
The 2 rear passenger doors have there own switches. Each of the switches contain a power window up and down relay. A switch activation alone can control the up and down functions of the rear windows. However the BCM, upon receiving a class 2 message from the DDM, can control the set of relays which will activate the rear window motors.

Jan 10, 2016 | 2004 GMC Envoy

1 Answer

Is there a fuse for the window switch


Which window switch ? RT DOOR CB-circuit breaker , do you know what a circuit breaker is ? 25A (System power for right rear window)
LT DOOR CB 25A (System power for left rear window
The power window system will operate anytime the retained accessory power (RAP) system is active or when the ignition switch is in the ACCY or ON position.
The DDM contains 4 power window switches which are integral components. Closing any of the normally open, rocker type switches provides the DDM with a request for power window operation. The switches for the 2 front windows have 3 positions Up, Down and Express Down, while the switches for the rear windows have only 2 positions, Up and Down. Each of these switches and their positions is a direct input into the DDM. Upon receiving a request for power window operation, the DDM, transmits a class 2 message indicating the switch and it's changed position.
The PDM contains a single power window switch that is an integral component. Closing of this normally open, rocker switch provides the PDM with a request for the front passenger power window operation. The switch for the front passenger window has 2 positions Up and Down. Each of these switch positions is a direct input to the PDM.
The 2 rear passenger doors have there own switches. Each of the switches contain a power window up and down relay. A switch activation alone can control the up and down functions of the rear windows. However the BCM, upon receiving a class 2 message from the DDM, can control the set of relays which will activate the rear window motors.


The power window system consists of the following components:
?€¢
Driver door module (DDM)


?€¢
Passenger door module (PDM)


?€¢
Body control module (BCM)


?€¢
LR power window switch


?€¢
RR power window switch


?€¢
Window up and window down relays in each of the rear passenger window switches


?€¢
Window lockout switch


?€¢
Reversible power window motors in each of the doors (circuit breaker protected)


?€¢
LT DOOR CB 25A (System power for left rear window)


?€¢
RT DOOR CB 25A (System power for right rear window)


If you not sure about any of this I suggest you take your vehicle to a ASE certified repair shop .

Oct 08, 2015 | 2002 Chevrolet TrailBlazer

3 Answers

My back automatic window went down and now won't come back up. No sound from motor. Checked fuses. Even took back seat apart but don't know what to do or what caused it. How can I get window to go...


it may need to be reset.

SECTION 501-11: Glass, Frames and Mechanisms 2001 Explorer Sport/Sport-Trac Workshop Manual
GENERAL PROCEDURES Rear Window Motor Initialization s1r~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure that no obstructions are present in the power rear window system when carrying out this procedure.
NOTE: This procedure must be carried out when repairs are performed on any part of the power rear window system including when: the power rear window motor is removed from the window regulator drum housing, a new power rear motor is installed, a new power rear window regulator is installed, a new power rear window module is installed, and any operation in which grease or lubricants are applied to the power rear window system.
NOTE: All power rear window components (window glass module, window regulator, window motor, and glass runs) must be installed and torqued to specification before carrying out this procedure.
NOTE: Steps 1-6 must be completed within 30 seconds. The entire procedure must be completed within five minutes.
NOTE: Once the ignition key is turned to the ON position in Step 6, it must remain on until the entire procedure is completed.
NOTE: Steps 7 and 9 require that the power rear window control switch be held in the closed position until the power rear window motor stalls the window in the upper header seal. Step 8 requires that the window control switch be momentarily turned to the open position.
  1. Start with the ignition in the OFF position.
  1. Turn the ignition to the ON position.
  1. Press the power rear window control switch vent button six times.
  1. Turn the ignition to the OFF position.
  1. Press the power rear window control switch vent button six times.
  1. Turn the ignition to the ON position. The power rear window will move up-down-up-down approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has entered initialized mode.
  1. Rotate and hold the power rear window control switch to the closed position until the window stalls in the upper header seal.
  1. Momentarily rotate the power rear window control switch to the open position and release. The power rear window will carry out a one-touch down operation until the window stalls at the bottom of the travel stop designed into the window regulator.
  1. Rotate and hold the power rear window control switch to the closed position until the window stalls into the upper header seal. Once this operation is complete, the window will move up-down-up-down approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has been successfully initialized.
  1. Verify correct operation of the power rear window by moving the window to the fully open, vent, then fully closed positions.
------------------------------------------------------------------------------------
  • The power rear window is inoperative (Explorer Sport Trac only)
  • Circuitry.
  • Battery Junction Box (BJB) fuse 3 (30A).
  • Central Junction Box (CJB) fuse 20 (7.5A).
  • Power rear window control switch.
  • Rear window glass motor.
  • Go To Pinpoint Test K .

------------------------------

Sep 15, 2011 | 2001 Ford Explorer Sport Trac

1 Answer

Where is the rear window relay located on the 2002 Ford Explorer sport trac. Not the rear door windows but the very back window.


  • The power rear window is inoperative (Explorer Sport Trac only)
  • Circuitry.
  • Battery Junction Box (BJB) fuse 3 (30A).
  • Central Junction Box (CJB) fuse 20 (7.5A).
  • Power rear window control switch.
  • Rear window glass motor.

NOTE: The power rear window motor is not on the multiplex link. Any diagnosis and testing carried out on the power rear window will not involve the GEM module. NOTE: The reinitialization procedure must be carried out when repairs are performed on any part of the power rear window system including when the power rear window motor is removed from the window regulator drum housing, a new power rear motor is installed, a new power rear window regulator is installed, a new power rear window module is installed, and any operation in which grease or lubricants are applied to the power rear window system.

Rear Window Motor Initialization s1r~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure that no obstructions are present in the power rear window system when carrying out this procedure.
NOTE: This procedure must be carried out when repairs are performed on any part of the power rear window system including when: the power rear window motor is removed from the window regulator drum housing, a new power rear motor is installed, a new power rear window regulator is installed, a new power rear window module is installed, and any operation in which grease or lubricants are applied to the power rear window system.
NOTE: All power rear window components (window glass module, window regulator, window motor, and glass runs) must be installed and torqued to specification before carrying out this procedure.
NOTE: Steps 1-6 must be completed within 30 seconds. The entire procedure must be completed within five minutes.
NOTE: Once the ignition key is turned to the ON position in Step 6, it must remain on until the entire procedure is completed.
NOTE: Steps 7 and 9 require that the power rear window control switch be held in the closed position until the power rear window motor stalls the window in the upper header seal. Step 8 requires that the window control switch be momentarily turned to the open position.
  1. Start with the ignition in the OFF position.
  1. Turn the ignition to the ON position.
  1. Press the power rear window control switch vent button six times.
  1. Turn the ignition to the OFF position.
  1. Press the power rear window control switch vent button six times.
  1. Turn the ignition to the ON position. The power rear window will move up-down-up-down approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has entered initialized mode.
  1. Rotate and hold the power rear window control switch to the closed position until the window stalls in the upper header seal.
  1. Momentarily rotate the power rear window control switch to the open position and release. The power rear window will carry out a one-touch down operation until the window stalls at the bottom of the travel stop designed into the window regulator.
  1. Rotate and hold the power rear window control switch to the closed position until the window stalls into the upper header seal. Once this operation is complete, the window will move up-down-up-down approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has been successfully initialized.
  1. Verify correct operation of the power rear window by moving the window to the fully open, vent, then fully closed positions
---------------------------------------------------------------------------------------------

Nov 16, 2010 | 2001 Ford Explorer Sport Trac

1 Answer

1998 VW Jetta GLS Manual Trans. The driver side power window won't roll down. From the same switch the front passenger window won't up but will roll down. The passenger side switch works fine; passanger...


If you have a multimeter you can go to the underside of the master panel in the drivers door and independently check the switches for voltage or with no power to the switch assembly check for continuity. Good place to start. If you get continuity to through the switch then you need to check power to the window actuators in the doors.

Jun 27, 2017 | 1998 Volkswagen Jetta

4 Answers

2004 Jeep Grand Cherokee driver side power windows do not work


I had the same problem with now power to windows, mirrors and seat. The common soulution is the orange and or black wire in the boot have broken between the door and post.

Nov 25, 2008 | 2004 Jeep Grand Cherokee

1 Answer

Only rear power window wont work, front are fine.


the window motors are most likely no good

Aug 15, 2008 | 2004 Chevrolet Colorado

2 Answers

Back windows are not rolling down


Rear windows on my 2002 Taurus stopped working. Fuse OK. Problem is only with the rear windows. Started as an intermittent problem on one window and now neither rear window works.

Jul 27, 2008 | 2002 Ford Taurus

Not finding what you are looking for?
2004 Saturn ION Logo

251 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8560 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...