Question about 1991 Subaru Legacy

1 Answer

Removing front rotar

Cannot remove front rotar to replace studs. 1991 Subaru Legacy

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Rotar doesn't contain the studs, the plate/hub behind the rotar does - you need a 32mm socket to undo the axle nut to then get at the hub (need a flat screw driver to lever the nut tang up first). If it's seized on put the rotar and wheel back on (leave the axle nut off) and gently rock it in a top-bottom motion (not radially or axially) to free it up. you can then gain access to the hub and studs. put the wheel nuts back on the studs 2 -3 turns so that you have a 'seat' and using a bolt with a smaller dia to punch them out

Posted on May 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace front the wheel bearing?


Remove the caliper and rotor, undo the axle, ball joint and the two strut bolts, and take the entire knuckle off. The hub is pressed off, then a circlip removed to press the bearing out. You need a hydraulic press to do this job.

Feb 21, 2015 | 1991 Subaru Legacy

1 Answer

How do I remove and replace the speedometer on a 1991 suburu legacy wagon I have a code for VSS2 which is the speedo speed sensor


The speed sensor is located on the transmission output . I don't think the problem is in the dash. Go to YouTube and type in where is the speed sensor on a 1991 subaru legacy and it will bring up all related videos. Hope you find this useful.

Feb 13, 2015 | 1991 Subaru Legacy

2 Answers

Need to replace a seal on transmission for a subaru legacy 1991 do i need to remove the whole transmission


are u talking about the front main seal? if so ,yes u have to take the trans. out to replace

Sep 06, 2012 | 1991 Subaru Legacy

1 Answer

Automatic transmission goes forward in reverse in 1991 subaru Legacy


Try removing the shifter cable from the shifter arm on the transmission . Remove the arm from the shaft on the transmission and position the arm 180 degrees and install it back on the shaft. reconnect the shifter cable to the arm and see what is does then. Outside of that I don't know.

May 20, 2017 | 1991 Subaru Legacy

1 Answer

1991 Subaru Legacy 2.2L not Turbo "Idle" very


i would check the idle air control solenoid first. simply unplug it then remove the unit and inspect the air passage for any blockage and carbon buildup. Clean it if its dirty then test it out. If the IAC is good then you should look at the throttle position sensor.

Aug 30, 2011 | 1991 Subaru Legacy

1 Answer

Left front wheel bearing is bad, need to change. on a 1991 Subaru legacy.


Basically you need to remove the hub and take it to a garage, it takes up to 10 ton to press a bearing out, and change both sides, otherwise you will get the right side problem very soon.

Sep 27, 2009 | 1991 Subaru Legacy

1 Answer

How to remove front axle of a 1991 subaru legacy


there is a roll pin which holds axle to trans remove this but be sure to put new axle in so you can see throught hole where pin goes it is not centered so axle can only go in one way or pin wont go back in

Jul 19, 2009 | Subaru Legacy Cars & Trucks

1 Answer

How do you remove front rotors on a 2007 subaru legacy


Remove wheel, Brake caliper then the Brake caliper support bracket. Then Rotor slides right off of Wheel studs. Remember to support vehicle properly, and to make sure brake calipers are fully compressed before removing. After caliper is removed try try to support it out of the way. Then on the bake of the brake caliper support bracket there are 2 bolts. Remove them and the rotor will have room to be removed from drive axle hub. Hope this helps and have a great day.

Jun 27, 2009 | 2005 Subaru Outback

1 Answer

How do I get my front brakes off my 1991 subaru loyale?


First you remove the wheels
#2 remove the 14mm bolt on the bottom of the calliper and swing the caliper up out of the way of the brake pads. It will pivot on the upper stud the caliper is on.
# 3 remove the pads out of the bracket.
NOTE you will need a special tool to "turn" the caliper pistons back in so you can fit it over the new brake pads.

Mar 31, 2009 | 1991 Subaru Loyale

Not finding what you are looking for?
1991 Subaru Legacy Logo

175 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...