Question about 2003 Audi A6

3 Answers

Prob's with my Audi A6 2003 Auto 3.0 V6 (gearbox)

Hi
Having prob's with my Audi A6 2003 Auto 3.0 V6, the gear selector display(PRND) sometimes flashes or has no display. when it is flashing & you move the gear stick to PRND or select the tip tron gears 1-6 the display just keeps flashing. in this state the car drives forward normally the only problem is when i select reverse, sometimes it reveres ok sometimes it doesn't i.e you can feel the gear engage but when you hit the gas the car doesn't move. I've had a mate diag it for me and I get the code/messages (17093 transmission range sensor, F125 Not a plausible signal P0706).So my question is do you think I need a new gearbox?? thks Marco

Posted by on

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

Doubt it as the fault suggests you need to look into the range sensor. If similar to Renault there is a switch on the gearbox that senses where the select lever is (at the gearbox end). If the display is wrong then the sensor needs looking at and either it will need to be adjusted into a set position by moving it, or perhaps the connector to it or wiring to/from it have a fault.

Posted on May 08, 2010

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Did it fix the problem with new TCM

Posted on Sep 26, 2012

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

UR screwed my friend, I'm fighting with it now, TCU is dead, I'm sending the unit for rebuild - just the TCU to xemodex.com, will keep U posted

Posted on Mar 16, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2003 mitsubishi eclipse v6 automatic with


Auto gearbox faulty! Could be synchro mesh or gear selector?

Oct 17, 2014 | 2003 Mitsubishi Eclipse

2 Answers

Flashing lights of the PRND and hard shift in Reverse


replace shifting s.w and brake light s.w .try to apply brake many time

Jan 12, 2014 | 2004 Audi A4

1 Answer

The O/D OFF light was flashing, fixed that but now lost all gears except 1st gear?


It sounds like you may have faulty shift solenoids. (internal transmission)

Oct 14, 2012 | 1993 Toyota Camry V6

2 Answers

I have a Audi A4 SE 2000 Reg. FE52UFB, with a I believe a Multi-tronic automatic 6 speed gearbox. I have flashing PRND lights. The car runs well, although very occasionally it has dropped out of gear,...


You really should not drive your car in that condition.Resetting codes will not help and it's a waste of money. All indicates problem with torque converter. Service immediately!!!!

Aug 10, 2010 | 2004 Audi A4

2 Answers

My prnd is flashing on and off and the car has no


you have a transmission problem. the tcm has switched to limp mode witch means the trans will start and stay in 2nd or 3rd gear only. this requires a scan tool to properly diagnose the problem. you should get it checked out sooner than later before any further damage is caused by driving it in its limp mode. good luck.

Nov 26, 2009 | 2003 Audi A4 Cabriolet

1 Answer

Audi a3


Does it keep running till the batt is flat? It could be the aircon condenser fan running - on the left as you stand in front of the car. This is a common prob with A3s of this age.
I have a '05 3.2L Quattro V6 and suffered the same prob. The batt is in the boot of the V6 and is sealed like Fort Knox so impossible to disconnect. After about 3 days with this the fan running constantly and having to put a charger on it every night I let the batt run completely flat to try and reset the complete system - no DIS lights - no starter motor clicks - DEAD. Then I jump started it and the prob disappeared completely. Everything is working perfectly ncluding the aircon. That was 4 days ago and 'touch wood' I've had no probs since. I know this won't work for everyone but it's worth a try before forking out £300+ for a new condenser fan unit. Good luck!

Oct 19, 2009 | 2005 Audi A3

1 Answer

Sometimes can't get reverse gear Audi A6 2004 Auto 1.9TDi UK


Unless your shade tree mechanic is an Audi expert, go to the dealer who has all the books and diagrams that tell the tech exactly where to look. The other guy may want to replace something just to troubleshoot and the factory tech should know exactly what to replace or which plug is loose.

Sep 20, 2009 | 2003 Audi A6

1 Answer

AUDI A6 SIX SPEED TIPTRONIC GEARBOX SEEMS TO BE IN WRONG GEAR AND APPEARS TO HAVE SLIPPING


I have been having similar problems. The clutch is slipping as thats how you get the variable gears when in full auto, but this is where the problem comes from, some garages (auto gearbox specialists) are now able to fix it. Do not go to Audi as all they do is replace the gearbox (very expensive). There is no quick fix though! Sorry for the bad news!!

Dec 02, 2008 | Audi A6 Cars & Trucks

1 Answer

1.8t multitronic problem


yeh got same prob.been like it for 3 months had fluid changed still doin it they found a fault.. code f115...i think..it a sensor in gearbox.£600 to get done learnt to live with problem for time bein.always seems to drive ok.and after i drive abot 20 miles all light seem to be ok.found that if i go 1 click on ignition pull down to n an start car all is ok except revers wich is ok after a short run.then do the same thing next time....but as soon as you put it in to p it al flashes again...and also when switchin off put it in to n..turn of ignition put to p and take out key...hope this helps for time bein

Jun 26, 2008 | 2003 Audi A4 Cabriolet

Not finding what you are looking for?
2003 Audi A6 Logo

1,386 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14363 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...