Question about Hyundai Santa Fe

3 Answers

Vehicle wont start.have fire and have fuel to the injectors.fuel pump, injectors,tps,maf,crankshaft sensor have all been replaced.

Posted by on

  • 1 more comment 
  • chas6string May 08, 2010

    vehicle has no distibutor. timing is correct.vehicle ran till fuel pump was changed.coils where replaced as well.

  • chas6string May 08, 2010

    this vehicle has no distributor.

  • chas6string May 09, 2010

    vehicle has no alarm system.could I have a bad crank sensor even though it was replaced?and if the crank sensor is bad will I still have fire and fuel?

×

3 Answers

Check your timing, if the timing is off then your car would not start. Replace your spark plugs, O2 sensor, distributor cap, and rotor

Posted on May 09, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyundai Master
  • 17,970 Answers

Several items there; here you can find a troubleshooting for no-start conditions: Diagnose/Index

Also, its possible that, when unplugged the battery, the antitheft system is armed. Test it.

Check the battery charge and adjust the crank sensor. Any OBD fault code there?

Tell us news.

Posted on May 08, 2010

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Expert
  • 4,070 Answers

Hi! Have you tried adjusting the distributor? It may need to be adjusted to get the perfect timing. ONce you get the perfect timing this will surely run. You can get the timing just requires a little patience. Hope this helps and good luck!

Posted on May 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Turns over wont start fuel pump works fireing plugs injectors have voltage what else needs checked


Fuel filter by be stopping fuel from reaching injectors. I always try the simple and less expensive things first. Also could be a sensor like cam or crankshaft they control the timing

Feb 18, 2014 | 2003 Ford Crown Victoria

1 Answer

96 Crown Vic will not start. Has spark, has fuel, crash button is set, has oil, Will run when fuel start is sprayed into carb. Any ideas ?


Check your fuel pressure to the Injectors at the pressure valve. Then check the wiring to the Injectors to see if they are getting power. Backtrack the Injector wiring if it is dead.

Your Crankshaft and Cam sensors would be working to supply the sparkplugs their power in the firing sequence. You need to check the part that supplies the Injectors their power in sequence.

Usually a bad TPS throttle position sensor will make a "Check Engine" light turn on. This part is on the drivers side of the Airhorn behind all the plastic Air filter ductwork. It has 2 screws and 1 electric connector. Unplug the connector and use an Ohmmeter to watch for resistance to change as you work the accelerator cable attached to the opposite side of the Airhorn. Connect the Ohmmeter to the TPS switch. The Resistance should change if the switch is good. If nothing happens, replace the TPS.

Jan 19, 2011 | 1996 Ford Crown Victoria

2 Answers

Injecters wont spray everything else is working fuel pump module what else is there


Check all of your fuses....and double check your fuel pump pressure..with a guage..to get atleast 3 readings...and if that is good, check the pressure after it goes through the fuel filter, to see if the pressure is still good..if not, replace the fuel filter

Nov 27, 2009 | Chevrolet 1500 Cars & Trucks

2 Answers

97 z71 vortec 5.7 replaced fuel pump.getting fuel but won't start


The # 5 cylinder is miss firing. not getting fuel. Could the injector just be stopped or the crankshaft sensor in gone.

Jun 26, 2009 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

CAR SOMETIMES WONT START


you are having a fuel delivery problem...and it could be caused by numerous things...such as a bad fuel pump, a bad cold sensor or warm up injector.  You haven't attempted to  solve any of these suspected faults...so take it to a mechanic for repair

Apr 11, 2009 | 1991 Volvo 940

1 Answer

Car wont start


check your fuel pressure it should be 35 psi .fuel pump relays dont go out but check all fuses with test light there is a fuel injector fuse but most likely problem is your fuel pump!

Mar 11, 2009 | 1991 Pontiac Grand Prix

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...