Question about 1994 Dodge Ram 2500

1 Answer

Wont start with key in crank poisiton starts after letting key back to run posi

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,309 Answers

The ignition switch is faulty, not sending signal on crank, replace it

Posted on May 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997monte carlo 3100 turns over wont start


I don't know what testing you have done, check the basics. Have a helper crank it while you visually check for spark at the spark plugs. If spark everywhere, use a gage and check proper fuel pressure. Also, check fuel injector pulse.
What about your security system? Is there a security lamp on the dash that is on or flashing when you try to start?

Apr 29, 2017 | Cars & Trucks

1 Answer

Motor turns over but wont start it fires like its trying to start but when I let off key from crank position it trys to start.


Causes can be numerous so here is some reading material which may help you track down your particular issue..........
Crank No Start

Nov 24, 2015 | Cars & Trucks

1 Answer

Will srart by the starter but not by the ignition and won't stay started


First let's define some terminology. The job of the starter motor is to "crank" the engine, if it does this, weather the engine runs is going to depend on the fuel system and the ignition system and good compression. Try this: with one hand, hold the key it the "crank" position, with your other hand, move the gear shift (slowly)from park to reverse to neutral to drive. Make sure you foot is on the brake as it may start in gear. If it starts while doing this, you have a bad neutral safety switch.
Also, It wont stay running when you crank it by jumping the starter if the ignition switch is off. Try doing it again with the key on. If it starts with the key on, and you jumping it at the starter, you probably have a bad, or out of adjustment, ignition switch. If it does not start, with the key on and cranking by jumping the starter, then you probably have a fuel or ignition problem.
Try the above and get back to me. I can walk you through how to check for fuel and spark if it still wont run.

Mar 09, 2014 | 1992 Cadillac DeVille

1 Answer

1989 ford f250 wont run with key in run position but will run while cranking


You would need to know if the coil has voltage when the key is in the on position.
The problem could be the ignition module, or the circuit back to the key switch. If the EEC relay is not working, you could have power for the coil in start coming from the starter relay-solenoid but not in run from the key switch.

Feb 22, 2013 | 1989 Ford F 250

1 Answer

My 2007 dodge caliber wont start


You are dealing with 2 possible problem. The ignition switch,or the alarm, If you have a alarm problem the vehicle will crank then in 2 seconds shut down,this is because the key is recognized,now if this is the problem roll down a window and disconnect the negative battery terminal,put the key in the ignition but in the off position.After 5 minutes reconnect the battery and turn the ignition on but dont crank the engine leave for 1 minute. Then see if that resolved the issue.Now if its an ignition switch problem crank the engine and slowly let it go.try to keep the key in the position where it stays running. By the way there is a campaign of a recall dealing with a TIPM software update Re-configure ,anti-theft system. Customer satisfaction notice G42. You will have to see the dealer for this campaign.

Nov 02, 2011 | 2007 Dodge Caliber SXT Sport Hatchback

1 Answer

My car wont start


sounds like security shut down which will start run for second then shut down after several time the security will shut down completely.......you can try what is called the relearn proceedure..this is what you dealer will do...might have to put battery charger on car first... then put key in ignition and turn to the run position do not crank leave it in the on position for ten minutes...... then turn key to the off position then back to the run position again for another ten minutes.....for the last time turn key off then back to run for the last ten minute cycle.... after the final ten minutes is up turn key to off position then attempt to start... let me know

Aug 31, 2009 | 1997 Chevrolet Cavalier

1 Answer

02 jimmy cranks but wont start it wants to start when you let go of the key


The electrical part of your ignition switch is going bad. While in the crank postion, you get voltage to starter and to the ignition circut, then when you let go of the key after it starts, the circut changes to the run mode for ignition-This is the mode that you are getting as you are letting go of the key.The circut for run on start up is bad. One caution when changing is that you have the passcode system, and may need to get a new key also, or at least get reprogramed in order to start.

Aug 27, 2009 | GMC Jimmy Cars & Trucks

1 Answer

Wont stay running


This sounds like it is your ignition module not sending message o your computer letting know that the key is in the ignition and the car has been started. Replace the ignition module

May 20, 2009 | 1995 Jeep Grand Cherokee

1 Answer

No start when hot


ignation control mogule,wen get hot expend and lose conection and will not start after cool down start normal also will cose no fuell presure fuell pump will not run,locatiom under coils.replece it

Mar 13, 2009 | 1991 Buick Skylark

1 Answer

1999 Chevy Silverdo cranks but wont start


ok check your timming belt then your ckt sensor the chip will not let the truck even crank or let the dash come on

Dec 07, 2008 | 1999 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...