Question about 2000 Jeep Cherokee

2 Answers

Turn signal does not work.

Where is the signal switch?

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 564 Answers

U may need a flasher instead,,i would go their first,,some are under dash,,some are near fuse box,,,

Posted on May 08, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 382 Answers

There is a relay in the fuse/relay box but chances are the actuator mechanism has gone defective. Remove the steering wheel and you can access the entire signal arm module, you can get one from a junkyard for around 50-100 dollars. They are very expensive new from a dealer.

Posted on May 08, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My rear turn signals are not working. front turn signals work rear parking lights work brake lights work


In the diagram for rear lamp, the top wires are voltage, the bottom black wire is ground. The brown wire on either side should be tail lamps, goes hot when you turn on the headlamp switch. The other top wire on either should be for turn signal. With everything turned on, is there voltage on that wire?
Because the front works and the rear don't, possible wiring circuit problem? The voltage for turn signals comes from bcm. The bcm knows when you turn on turn signal switch, either side, then the bcm sends voltage to turn signal lamp at the rear and front.

rear-turn-signals-not-working-front-nrw1b5lbo1usuvcsnuvurzx3-3-0.jpg

Oct 17, 2016 | 2009 Chevrolet Chevrolet HHR LS

1 Answer

My turn signals sometimes will quit working then I have to hit the hazard lights button leave it on and then turn my turn signals on then they work what causes this to happen


When the turn signals quit working pull up , down , front to back an back to front on the turn signal switch handle . Do they work when doing this ? Pontiac had bad switch . The power for the turn signals goes through the flasher / hazard module . Could be the switch or the module.
The HAZARD LPS fuse in the left hand instrument panel (LH IP) junction block supplies battery positive voltage to the flasher module, which is part of the hazard switch assembly. The TURN LPS fuse in the LH IP junction block supplies ignition positive voltage to the flasher module. The turn signal lamps may only be activated with the ignition switch in the ON position. When the turn signal switch is placed in either the left or right position, current flow is from the flasher module's output to the turn signal switch assembly. The flasher module then sends an on-off voltage signal to either the left or right turn signals and their instrument panel cluster (IPC) indicator. When the hazard switch is pressed, all the turn signal lamps will flash including both IPC turn signal indicators.

Mar 12, 2016 | 2001 Pontiac Grand Am GT

2 Answers

Brake light trouble right side brake light will not come on but both flashers work also turn signals work older ford truck what could the problem


I have to think the problem is inside the turn signal switch, a poor internal connection. You know the brake signal first goes through the turn switch before it goes to the bulbs. That is why the brake lights and rear turn signal lights share the same filament in the bulb, and the same wire going to those lights. The only difference is the turning side light is affected by the turn signal flasher, causing blinking, while the other side- the non turning side-does not go through the flasher relay, but straight to the bulb from the turn signal switch. Change your turn signal switch and I believe you will solve the problem. Let me know, okay?

Sep 16, 2015 | Ford Cars & Trucks

1 Answer

2000 tacoma flashers don't work but turn sig do work!


The hazard switch gets power from the horn fuse which is hot all the time, and from the turn signal fuse which is hot when the key switch is on. The turn signal switch gets power from the hazard switch and both use the same flasher.
So if the turn signals work but the hazard switch does not power the lights, and both fuses have power, I would say the problem is inside the hazard switch.

Feb 19, 2013 | Cars & Trucks

1 Answer

Window break light good but actual break lights not working


sounds like you have a bad turn signal switch.

If the third brake light is working than we know the fuse is good and the switch is good. The third brake light bypasses the turn signal switch. If the rear turn signals are working than we also know that the wiring from the switch to the rear bulbs is also good. The brake lights and the turn signals are on the same bulb so the turn signal switch is what determines if the bulb gets power from the brake light switch or from the turn signal flasher. If the switch is bad usually the first thing that stops working is the brake lights.

Typically you can wiggle, jiggle, pull, push on the switch lever with you foot on the brake and get the brake lights to work. Sometimes turning the four way on and off several times will also get the brake lights to work. If this is the case than a new turn signal switch will solve you problem.

If you have any questions let me know!

Oct 11, 2011 | 1997 Chevrolet Lumina

2 Answers

95' Buick regal, 3rd brake light works, tail lights work, turn signals work, stoplight switch seems to work ie 3rd brake light working, fuse is ok, changed bulbs, but no rear brake lights.


If the third brake light works and the regular ones don't, it is most likely a bad turn signal (multifunction) switch. The switch is able to kill the brakes lights to run the turn signals, and in rare circumstances does this. I've seen it several times. It could also be wiring, especially near the turn signal switch, but it is usually the switch.

Nov 25, 2009 | 1995 Buick Regal

1 Answer

REAR BRAKE LIGHTS DO NOT COME ONLY TAP LIGHT IS


Check for power at the turn signal switch. White wire comes from brake switch switch into the turn signal switch. The brake light switch is working because the high mount brake light is working..right? Do the turn signals work ok? if so, then the wiring is OK. The brake signal wires that come out of the turn signal switch are dark green(right) and yellow (left).

Oct 27, 2009 | 2001 GMC Safari

2 Answers

96 monte carlo rear window brake light works but not brake lights. tail lights work, blinkers work, replaced brake switch and bulbs still not working


This is a common GM specific problem. Your turn signal switch contains an elaborate networking device that has to cancel brakelights while running a turn light. Often times the ground within the turn signal switch is lost causing your situation. After investigating such other possibilities as fuses and loose grounds it may become necessary to replace the turn signal switch. Thank you, Dana

Sep 21, 2009 | 1998 Chevrolet Monte Carlo

1 Answer

1998 Cavalier rear turn signal doesn't work


The turn signal switches are known to go bad, try to use the turn signal switch and jiggle the lever after clicking to the left turn. Replace signal switch assembly.

Jul 19, 2009 | 1998 Chevrolet Cavalier

Not finding what you are looking for?
2000 Jeep Cherokee Logo

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...