Question about Toyota Pickup

Open Question

2006 Toyota Hilux 2.7 VVTI 2x4 Single Cab - brake shoe assembly - can not put it all back together again, please help

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: toyota hilux dual cab. looking for fuel filter location

ITS ON THE PASSENGER SIDE OF MOTOR RIGHT ABOVE STARTER

Posted on Apr 16, 2009

jagjeffery
  • 316 Answers

SOURCE: toyota hilux 96 model 4x2 single cab

If you have the 3.4 V6 engine yes you have a timing belt and you shouild change it every 90 thousand miles if you have the 4 cylinder engine no you do not it is chain driven

Posted on May 29, 2009

  • 151 Answers

SOURCE: diagram for the timing of a toyota hilux 2.o vvti

get a Haynes manual. @$20 at autozone. money well spend as you will get lots of use from it if you work on your vehicle

Posted on Feb 15, 2010

  • 233 Answers

SOURCE: how do you adjust the brake shoes on the Hilux

I am assuming you are speaking of the rear brakes. If that is the case, then it is not hard to adjust. Jack up the rear of vehicle and remove back wheels. This can be done one at a time or you can remove both wheels at same time. There should be a hole in the drum near the top. Insert a flat blade screwdriver into hole and push down. It should be resistance when pushing. Or, you can put the vehicle in reverse and back up about 50 yards and hit the brakes hard. Do that a couple of times.

Posted on Feb 15, 2010

  • 21 Answers

SOURCE: where can I get a free owner's manual for a toyota hilux 2006

This site is saying it will let you download a PDF version of the owners manual awell as a service manual-> http://toyotaownersmanuals.info/category/toyota-hilux/

This site also is suppose to have access to them: -> http://www.toyota.com/owners/web/pages/resources/owners-manuals#

Otherwise I'd say try Ebay,

Good Luck

Posted on Dec 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can anyone please assist me? I'm looking for the specs on the 2.7 vvti hilux raider d/c


Herman, Google search your year,make and model# specifications or manual. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Toyota Hilux Wikipedia the free encyclopedia
Hilux facelift driven in Bloem
http://www3.toyota.com.au/hilux/specifications/workmate-4x2-single-cab-cab-chassis-4-cylinder-petrol-manual

Aug 22, 2016 | Toyota Cars & Trucks

1 Answer

How do I know if my newly bought 2011 Toyota Hilux Raider 2.7 vvti a Legent45 is or not? It carries the nudge bar of a 45


US VVTI models have VVTI on the plastic engine cover..i would assume all models do. You could have a dealer check the VIN. ...

Aug 22, 2016 | Toyota Cars & Trucks

1 Answer

Toyota hilux vvti 2.0 does not rev. I have cleaned up the throttle body and still does not rev.


NO YEAR?
scans good, no stored or pending DTC codes>????????
dirty MAF, (if MAP EFI, clogged map port?)
low fuel pressure>?
bad need of simple tuneup?

Feb 09, 2014 | 2006 Toyota Hilux 2.0

2 Answers

Rear brakes


Removal
1.Remove rear wheel and tire assembly from vehicle.

2.Remove rear brake drums from hub and bearing assemblies after loosening the two brake drum screws.
bj6c017a.gif
3.Be sure that the parking brake pedal is in the release(most upward) position.

4.Completely loosen square nut of the rear parking brake cable. Then create slack in the rear parking brake cables.
bj6c017b.gif
5.Remove adjuster spring from adjust lever and brake shoe.
bj6c017c.gif
6.Remove adjust lever and turn the adjusting wheel of adjuster assembly to the direction of the arrow as shown.
bj6c017d.gif
7.Remove the strut spring and the lower retracting spring from the brake shoe.
bj6c017e.gif
8.Remove the upper return spring from the brake shoe.
bj6c017f.gif
9.Remove brake back plate hold down spring and pin from the leading brake shoe assembly.

10.Remove the leading brake shoe. Then remove the adjuster assembly, strut and anchor spring from the trailing brake shoe.
bj6c017g.gif
11.Remove the trailing brake shoe from the brake back plate after removing hold down spring and pin.
bj6c017h.gif
12.Remove the trailing brake shoe from the rear parking cable.
bj6c017i.gif
13.Remove parking pivot lever from the leading brake shoe.
bj6c017j.gif
Replacement
1.Lubricate the eight shoe contact areas on the back plate and anchor.
bj6c017n.gif
2.Install the trailing brake shoe to the rear parking cable.

3.Install trailing brake shoe on brake back plate and install the trailing brake shoe hold down spring and pin on the brake shoe.

4.Tighten the square nut of rear parking cable.

5.Install the anchor spring then install adjuster assembly, and strut.

6.Install leading brake shoe on brake back plate.
bj6c017o.gif
7.Install the brake shoe upper return spring, strut spring and the lower retracting spring to the brake shoe.

8.Properly rotate the adjusting wheel of adjuster assembly to the direction of the arrow in as shown.
bj6c017d.gif
9.Install the adjuster spring on the adjust lever and leading brake shoe assembly.

10.Install the leading brake shoe hold down spring and pin on the brake shoe.
bj6c017q.gif
11.Adjust brake shoes assemblies so as not to interfere with brake drum installation.

12.Install the rear brake drums on the hubs.

13.Check and adjust whether the pedal stroke in the specification.(Refer to section BR Gr./On-vehicle service/Pedal stroke of parking brake)

14.Install wheel and tire.

15.Push the parking brake pedal to the floor once and release pedal. This will automatically remove the slack from and correctly adjust the parking brake cables.

16.Test the vehiche on the road. The adjust will continue the brake adjustment during the road test of vehicle.

Inspection
1.Inspect the disassembled parts for wear, rust or damage.

2.Measure the thickness of brake shoe lining.
Standard : 0.17 in (4.5 mm)
Minimum : 0.04 in (1 mm)

3.If the shoe lining is less than minimum or shows signs of uneven wear, replace new one.
bj6c017k.gif
4.Measure the inside diameter of the brake drum.
Standard : 10 in (254 mm)
Maximum : 10.07 in (256 mm)
bj6c017l.gif
5.If the inside diameter of the brake drum is more than maximum or shows signs of uneven wear, replace new one.

6.Inspect the lining and drum for proper contact. If the contact condition is improper, repair it with a grinder or replace the brake shoe assembly.
bj6c017m.gif

Aug 14, 2013 | 2002 Kia Sedona

1 Answer

How do you replace the rear brakes on a 2001 Ford F250


First, get a set of brake shoes.
Second pull off wheels on both sides then remove the brake drums on both sides.
On one side pull off brake shoes springs clamps ect.
Using the side not dissasembled as an example, use it as a reference while assembling the side apart. Then pull apart the other side, and use the side reassembled to put together that side using it as a reference.
Replace drums and wheels, good luck, and give me a nice vote please.

Jul 12, 2010 | 2001 Ford F250 Super Duty Super Cab

1 Answer

Diagram for the timing of a toyota hilux 2.o vvti


get a Haynes manual. @$20 at autozone. money well spend as you will get lots of use from it if you work on your vehicle

Feb 15, 2010 | 1994 Toyota 4Runner

2 Answers

How to install front brake shoes on 1998 toyota camry


just take off tire take a clip out and pull out front shoe and take off roter then the back push in the cylender with a c clamp and revers the process of the calaper might come off using boltes then same process

Aug 29, 2009 | 1998 Toyota Camry

1 Answer

I need a schematic for the rear brakes on an F150 super cab with 4.6L automatic trans 4wheel drive


Drum, Rear Brake System Standard Rear Brake
9969082.gif
Item Part Number Description 1 2069 Brake Shoe Hold-Down Spring Pin 2 — Rear Wheel Cylinder Retaining Bolt (2 Req'd) 3 — Washer (2 Req'd) 4 — Anchor Pin (Part of 2211) 5 — Wheel Cylinder 6 2028 Brake Shoe Anchor Pin Guide Plate 7 2A637 Parking Brake Lever 8 2296 Brake Shoe Retracting Spring (Short) 9 2296 Brake Shoe Retracting Spring (Long) 10 2200 Rear Brake Shoe and Lining (Secondary) 11 — Washer 12 2106 Parking Brake Lever Pin Retainer 13 — Brake Shoe Adjusting Lever Cable Guide 14 2A642 Primary Brake Shoe Parking Brake Lever Link 15 2A601 Parking Brake Link Spring 16 2068 Brake Shoe Hold-Down Spring 17 2A176 Brake Shoe Adjusting Lever 18 2048 Brake Shoe Adjusting Screw Socket 19 2047 Brake Shoe Adjusting Screw Nut 20 2041 Brake Adjusting Screw 21 2049 Brake Shoe Adjusting Screw Spring 22 2200 Rear Brake Shoe and Lining (Primary) 23 2A178 Brake Shoe Adjusting Lever Cable 24 2211 Brake Backing Plate
Heavy Duty Rear Brake
6dcb5d2.gif
Item Part Number Description 1 — Rear Wheel Cylinder Retaining Bolt 2 00538 Lock Nut 3 2212 Rear Brake Backing Plate 4 2262 Rear Wheel Cylinder 5 2A642 Primary Brake Shoe Parking Brake Lever Link 6 2A601 Parking Brake Link Spring 7 2A637 Parking Brake Lever 8 2106 Parking Brake Lever Pin Retainer 9 — Parking Brake Lever Bolt 10 — Secondary Shoe Assembly 11 2A179 Brake Shoe Adjusting Lever Cable Guide 12 2068 Brake Shoe Hold-Down Spring 13 — Adjusting Lever Pin 14 — Adjusting Lever Return Spring 15 2A176 Brake Shoe Adjusting Lever 16 2047 Brake Shoe Adjusting Screw Nut 17 2049 Brake Shoe Adjusting Screw Spring 18 2041 Brake Adjuster Screw 19 — Primary Shoe Assembly 20 2068 Brake Shoe Hold-Down Spring 21 2200 Rear Brake Shoe and Lining 22 2035 Brake Shoe Retracting Spring 23 2A178 Brake Shoe Adjusting Lever Cable 24 2092 Brake Adjusting Hole Cover 25 2069 Brake Shoe Hold-Down Spring Pin
The rear drum brakes:
  • Have internal shoes that expand against the brake drum (1126).
  • Are a single-anchor type.
  • Are actuated by one rear wheel cylinder (2262).
  • Have two pistons in the rear wheel cylinder (2261). One exerts force against the upper end of the primary shoe; the other exerts force against the upper end of the secondary shoe.
  • Adjust rear brake shoes and linings (2200) automatically.
  • Need manual brake adjustment if the adjusters are not operating properly or after the rear brake shoes and linings have been replaced.
When the brake pedal is applied, hydraulic fluid pressure forces the pistons in the rear wheel cylinder outward, moving the rear brake shoes and linings against the brake drum.
The rear drum brake system includes the parking brake mechanism. Refer to Section 206-05 .

Apr 04, 2009 | 1997 Ford F150 Regular Cab

1 Answer

Rear brake assembly


hi mate do a google search for 85 hilux rear drum brake diagram and it will give you a few pictures i had the same prob and helped me to fix it

Mar 13, 2009 | 1985 Toyota 4Runner

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

315 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...