Question about Hyundai Motor 1994 Elantra

1 Answer

Settings and the valve clearances

My excel suffered a rocker roller colapse and i have r&rd the head but just need the head bolt torque settings and the valve clearances, as the local dealer is happy to sell the gasket kits but not technical information, any help would be greatly appreciated.
]

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 144 Answers

Valve Setting is usually done only by authorised service center of Hundai, because if you do the setting wrongly it may hurt the car performance. Kindly go to the car service center or you can get the data only by visiting any Hundai service center directly.

Posted on May 08, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rocker arm pivot torque for olds cutlass 1987 307


Oldsmobile Torque Specs - GbodyOlds.com

www.gbodyolds.com/forum/showthread.php?754-Oldsmobile-Torque...
Feb 7, 2013 - 2 posts - ‎2 authors Oldsmobile Small-Block Engines Cylinder Head Bolts (1/2in. bolt) 130 ft. lbs. Cylinder Head ... Rocker Arm Pivot Bolt 25 ft. lbs. Rod Bearing ...

Rocker Arms - AutoZone

www.autozone.com/...Cutlass...1987.../Rocker-Arms/_/P-0900...

AutoZoneGM Cutlass RWD 1970-1987 Repair Guide ... To remove the rocker arms from the shaft, the nylon arm retainers must be removed. ... 7: Engine valve system, 260, 307, 350, 403 Oldsmobile built engines ... Unfasten the two bolts that attach the rocker arm pivot to the cylinder head. ... Torque the retaining bolts to 25 ft. lbs.

Dec 01, 2015 | 1987 Oldsmobile Cutlass Salon

1 Answer

Torque setting for 1972 Cororna


My manual shows an 8RC for 70 and 71 and an 18RC for the 72-74

18RC valve clearance HOT IN .008 EX .014 cold spec. .007 .013
Cyl head 72-82 Ft Lbs
Rocker caps 12-17 ft lbs
cam bearing clearance .001-.002
cam endplay .0017-.0066
oil tube 11-16 Ft Lbs

Jun 15, 2013 | Cars & Trucks

2 Answers

Please assist with Cylinder Head Torque and Valve Clearance Specs for Tata Indica 1.4 LXi


i need the head talk settings & valve clearance for tata indica lxi

Apr 20, 2013 | 2006 Tata Indica LXi

1 Answer

Torque settingsfor head on lister petter mini6 engine


I have just rebuilt one for our Westerly 21. This is from my Petter 'A' range workshop manual:-
The water cooled engines (AC1W etc.) are:cylinder head nuts: 30NM (22 lbft) except 32.5NM (24 lbft) for the one that also holds the rocker.
Valve clearances are 0.1mm (0.004") COLDReset valve clearance after one hours running since torquing the head.
Retorque head and set valve clearance after initial 20 hours running
I believe Mini-6 refers to the water cooled engines but just in case, the air cooled engines are 27N (20 lbft)

Mar 27, 2012 | Cars & Trucks

1 Answer

What is the valve clearance and head bolt torque on a nissan td27 engine 1996 model


valve clearance is .014 inch for intake and exhaust with engine warm.
head torque it 21 ftlbs, then 44 ftlbs, then loosen all, torque to 89 inchlbs, then to 21ftlbs, then mark and turn the bolts an additional 60 to 65 degrees.
cyl head sub bolts torque 80 to 100 inchlbs.
thanks.

Jan 13, 2011 | 1990 Nissan Hardbody King Cab

1 Answer

I have oil leakin on top of my spark plug wires in the tube ive changed the valve cover gasket 3 times i even put high heat cilcone over around the spark plug tubes but all it does is slow it down im not...


Two things:

1. Make sure you torque the bolts down to the right specification, which is 83 inch pounds (or about 7 ft lbs). Work opposite end of the cover and start with a lower torque first (like 50 in lbs), then go up to 83. It's just a good practice.

2. If that does not work, get a Fel Pro gasket set VS50365R (pic below). What is special about this set is the really thin o-rings there in the middle. Those are the rocker arm tube seals. You need to take the rocker arms off in order to replace them, but this way you're doing a complete job and you probably won't have that issue again. If you don't want to get the whole set again (since you already replaced most of it 3x over), you can probably just go to a honda dealership and pick up the 4 you need.


44db60b.jpg
Here are the seals under the rocker arms:

ea6e49b.jpg
If you decide to do this yourself, it's a good idea to get a set of feeler gauges so you can properly gap the clearance from the rocker arms to the valves. Intake valves should be gaped to .010 in, and exhaust valves to .012 inches. Also, yes, you can take the rocker arm assembly off without removing the distributor...just take off that one bolt that is in the way. The torque for the bolts holding in the rocker assembly is 9 ft-lbs for the smaller 6x1mm bolts and 16 ft-lbs for the larger 8x1.25mm bolts. Here is the torque sequence...

94f3f23.jpg

Oct 06, 2010 | 1992 Honda Accord

2 Answers

What are the torque measurements for the rocker arms and intake manafold?


2.2L Engine & 2.4L Engines
These engines are not equipped with rocker arms. The camshafts directly actuate the valves.

3.1L Engine & 3.4L Engines
When install or connect the check the following:
- Pushrods and the rocker arms. Torque the bolts to 24 ft. lbs. (32 Nm). - Rocker arm cover using a new gasket. Torque the rocker cover bolts to 89 inch lbs. (10 Nm).
- Heater bypass pipe. Torque the screw at the water pump to 106 inch lbs. (12 Nm), the bolt at the cylinder head corner to 18 ft. lbs. (25 Nm) and the nut to 18 ft. lbs. (25 Nm).


About the INTAKE MANIFOLD...
-
Intake manifold nuts and bolts and tighten to 89 inch lbs. (10 Nm)
- Pushrods and rocker arms. Torque the bolts to 89 inch lbs. (10 Nm) plus an additional 30 degree turn. - Lower intake manifold. Apply sealant to the threads of the bolts and torque the bolts to 115 inch lbs. (13 Nm).



859cdc3.jpg

Exploded view of the upper and lower intake-3.1L & 3.4L engines


fe92b8b.jpg

Fig. Lower intake manifold tightening sequence-3.1L & 3.4L engines

Hope help.

May 04, 2010 | 2000 Pontiac Grand Am GT

1 Answer

I have 4.9L6 need torque specs for cylinder head


for cylinder head the torque is : step 1 55 ft-lb, step 2 65 ft-lb, step 3 85 ft-lb. Rocker arm stud nut or bolt is 17 to 23 ft-lb. and valve cover bolt 72 to 108 in-lb.


e023442.jpg

Dec 05, 2009 | 1988 Ford F 150

2 Answers

Oil leak from rocker box on 1996jeep cherokee2.5td


Get you a new gasket for the rocker cover, make sure you clean the mating surface good,and all traces of old gasket, and silicon etc. make sure you dont overtighten the bolts to the rocker cover. the torque for the rocker cover is 35 in lbs (4nm). as far as vavle clearance it is none adjustable. A clicking valve can indicate worn lifters, sometimes an oil change will quiet down noisy lifters. If noisy lifters persist you would have to service the heads. If you decide to do that yourself you can ask for a procedure on that too later on. Removal of the head is very difficult, because you need to remove a lot of things, and require you to do a timing on the engine.

Jul 01, 2009 | 1996 Jeep Cherokee Country

Not finding what you are looking for?
Hyundai Motor 1994 Elantra Logo

197 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...