Question about 1994 Honda Civic

1 Answer

I have a viper alarm on my car that wont shut off nor i cant start the car..and i have tried the button under my dash, how Can i shut it off??

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 161 Answers

Was it a professional or shade tree install? the following is off vipers website:
disarming without a remote control
This feature allows you to disarm the security system without the
Remote Control should it be lost, damaged, or disabled. In order to
disarm the system without a remote remote control, you must have
the vehicle’s ignition key and know where the Valet button is
located. Be sure to check with the installer for the location and the
number of presses of the Valet button required to disarm the system.
To disarm the security system,
turn the ignition to the ON position.
Press the Valet button the
preset number of times (one to
five times) within 15 seconds. After five seconds the system will
disarm. If the system does not disarm, you may have waited too long;
turn the ignition off and on and try again.
if that doesn't work try this other

valet mode
You can prevent your security system from automatically arming
and triggering by using Valet Mode. This is very useful when
washing the vehicle or having it serviced. In Valet Mode, the
security system will not arm, even with the Remote Control, but
all convenience functions (door locks, trunk release, etc.) will
continue to work normally.
To enter or exit Valet Mode:
1. Turn the ignition on.
2. Turn the ignition off.
3. Press and release the Valet
button within 10 seconds.
The status LED will light solidly if you are entering Valet Mode,
and it will go out if you are exiting Valet Mode.

Posted on May 08, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The battery was changed on my car. after new one installed the alarm went off. the guy push the black button and turned the key. now the alarm wont work. how do i get it workind again? .


the guy pushed a button under my dash turned the key and car started

you need to know where that push button is under the dash

if you cant find it your self ... ring the place back for instructions

not nice but
you may have to get them to call out and show you or
tow the car back to where you got the battery fitted

Oct 11, 2016 | Cars & Trucks

2 Answers

The viper alarm reset on my car how do I disarm it?


some you can push a button under the dash with the key in the on position and i had some disconnect the battery turn the key to the on position and hook the battery up

Aug 04, 2012 | 2005 Nissan Altima 2.5

1 Answer

Kill switch on fuel pump relay switch


If your timing belt is slightly off by a tooth or more it wont stay running. if the cam and crank sensors dont see the same #1 strock at the same time it causes rough running and stalling problems, as for your viper reach under your dash and take the fusses out. this will dissable it.

Dec 15, 2011 | 1991 Eagle Talon

1 Answer

When i start the car the alarm when on and the car wont start


Aftermarket alarm, look for the small button under the dash or hiding under the steering area press and hold it then crank and start the vehicle. If you cant find it be prepared to just remove the alarm system you will need to go under the dash at the ignition starter signal and remove the alarm starter relay and restore it to its original way. depending and the manufacture of the alarm these alarm that where installed for Toyota are a headache and fails all the time

May 22, 2011 | 2002 Toyota Camry

2 Answers

How do I reset my Dodge Viper 1994 alarm? My battery died and my alarm shut down my engine.


Try locking and then unlocking your car with the key in the drivers door. This should reset it

Nov 16, 2010 | 1994 Dodge Viper

1 Answer

I have a 2007 Toyota Corolla type S. My problem is that when I press the unlock button on my remote the doors unlock and the lights flash however when you open the door the alarm sounds. It has been...


This sounds like a bad alarm module, the doors unlock but the alarm doesnt shut down, so it wont let you start it because its not shutting down, the light flash and door unlock put starter disable and horn stay active, most good alarms have liftime module warranties, if you take it back to who installed it and ask them or if it was already in the car when you bought it then you will need to disable or replace it. hope this helps, also to disable it just trun key on then open a open try key off and within 10 sec push the button under the dash its a small red button this will put it in vallet mode.

Nov 10, 2010 | 2003 Toyota Corolla

3 Answers

The alarm isactivated and I can't get into the car. I only have the key


PUT THE KEY IN THE IGNITION AND TURN THE KEY ON FOR 10 MINUTES AND THEN SHUT IT OFF AND THEN TRY TO START IT IF NOT DO IT AGAIN

Oct 23, 2010 | Buick Rendezvous Cars & Trucks

3 Answers

My 1998 dodge intrepid wont start and the alarm wont shut off


Try "cycling the key in the passenger door lock. Turn it all the way to the right and all the way to the left.

Jul 16, 2010 | 1999 Dodge Intrepid

1 Answer

Have a viper alarm installed and a factory alarm


try removing the remote fob battery for 10 secs then replacing, i get this problem a lot if the fob battery is low.

Feb 25, 2009 | 2007 Toyota Tacoma

1 Answer

Viper Alarm System problem


Look for a push button under the dash, should be black, turn key on and hit button.. should go into "valet mode".. hopefully you will be all set...

Jan 23, 2009 | 2000 Dodge Viper

Not finding what you are looking for?
1994 Honda Civic Logo

1,926 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...