Question about 1993 Nissan Maxima

Open Question

Whats wrong with my windshield wiper motor/wipers? all they are doing is tweaking back and forth about a 1/4 of a inch and nothing more if u put on high on wipers they do it faster?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 840 Answers

SOURCE: The wiper arms on my 2001 Nissan Pathfinder SE don't work.

there are no screws they are retainers that pop off / the trick is to be careful pulling off the vent cowl panels because the clips can be hard to get look what side you need to take off and their may be ends which should come off first.

Posted on Jan 25, 2009

Ad
localwonder
  • 6784 Answers

SOURCE: 1996 nissan sentra windsheild wipers not working

This is the relay switch and its located inside the dash board. the part itsefl will cost 40.00

Posted on Mar 10, 2009

erickg
  • 116 Answers

SOURCE: i have a 2002 nissan altima. the wipers only work

motor must be bad

Posted on Apr 23, 2009

FixurNissan
  • 61 Answers

SOURCE: my 07 nissan murano rear windshield wiper doesn't

You need to adjust the wiper arm location. Loosen the 12 mm or 10 mm nut that holds the rear wiper arm. Wiggle the arm until it comes off. Then turn on the rear wiper for a second and turn it off, leaving the key on. This way the rear wiper motor will do it's sweep, and them park where it's suppose to. Then reattach the rear wiper arm and secure the nut and recheck.

Thanks Jay!

Posted on Jul 22, 2009

  • 31 Answers

SOURCE: both Windshield wipers quit working at the same time

Its easy. 6 bolts hold that trim on remove them and gently remove the trim

Posted on Nov 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I've got a 2000 dodge dakota i need to see what position does the windshield wiper arms need to be in after i replace the wiper motor


Hi.

It's pretty easy, you do not need to know the position, the wiper motor always return to it's origin, just activate the wiper motor by briefly using the washer fluid switch for instance, let it finish it's movement. Next, you want to place the wiper arm with the longest blade on the driver side. Now for the height, most car's wiper sit from 0.5 to 1 inch above the base of the windshield so that should be what you're aiming for, if the wiper arms pinion has splines, try to pick the one closest to the windshield but not too close of course and repeat the same steps for the passenger side. Now you should check the wiper arm operation for collision, incorrect height or travel distance and adjust the wiper arm position accordingly. By the way, if you're lucky your windshield may have mark on the base of the tinting of the windshield to indicate the height of the wiper blade

Nov 22, 2014 | Cars & Trucks

1 Answer

Gmc savana windshield wipers


I would make an assumption as it is the wiper motor going bad. Most any I have seen the motor runs in a constant 360 degree revolution and not back and forth. The back and forth motion comes from the linkages under the plastic cowl in front of the windshield.

Apr 04, 2014 | 2005 GMC Savana

2 Answers

2009 Touareg passenger side windshield wiper arm does not move but driver side does


sounds like the connecting rod between both wiper arms either broke or one of the keepers popped off under the connector for that arm..since the wiper system IS NOT designed to wisk snow off the window once accumulated, this can an does happen.. even seen motors get burned out doing this..cleaning the window first will save this issue and the equiptment. need to acess this arm<take off the vented peice below the windshield and everything should be visible there..repost findings

Feb 05, 2013 | Cars & Trucks

1 Answer

Windshield wipers just stop working but I hear motor running.


Must be a loose nut on the wipers, or the arm on the wiper motor.

May 26, 2009 | 1998 Lincoln Mark VIII

1 Answer

Windshield wiper link that connects to motor comes


im afraid its the linkage replacement the grease is just there for the lubrication what usually happens is they wear out and only alternative is to replace the linkage

Apr 10, 2009 | 2007 Ford Focus (3 Door) Hatchback

1 Answer

ROVER MGF.REMOVING WIPER MECHANISM.


Pivot Shafts and Linkage
The windshield wiper assembly is mounted below cowl top extension (021A36) . Linkages are connected with non-removable plastic ball joints. Windshield wiper mounting arm and pivot shafts are an integral part of the windshield wiper and are serviced as one unit. Removal
  1. Disconnect the battery ground cable (14301). Refer to Section 14-01 .
  1. Remove antenna mast from the antenna base.
  1. Remove cap on LH and RH windshield wiper pivot arms to expose nuts retaining the arms to pivot shafts.
  1. Remove two nuts, one from each of windshield wiper pivot arms . Lift wiper arms to service position, carefully rocking them back and forth to loosen them from the pivot shaft. Lift off windshield wiper pivot arms .
  1. Remove seven screws retaining the cowl top vent panel.
  1. Disconnect windshield washer hose (17A605) at LH side of vehicle just ahead of where it enters cowl top.
  1. Remove hood cowl seal.
  1. Carefully remove cowl top vent panel from vehicle.
  1. Remove three retaining screws to cowl drain tube that is connected to top cowl.
  1. Disconnect wiring harness leading to windshield wiper motor.
  1. Remove five screws retaining cowl top to vehicle and remove cowl top and windshield wiper from vehicle.
  1. Remove two screws and two nuts retaining windshield wiper to cowl top and separate the two parts.
  1. Remove drive linkage from motor shaft linkage.
  1. Remove remaining screws attaching windshield wiper and separate the two parts.
1086bde.gif

Item Part Number Description 1 02010 Cowl Top Panel 2 N621906-S2 Nut (2 Req'd) 3 17508 Windshield Wiper Motor 4 N805605-S36 Screw (2 Req'd) 5 17500 Windshield Wiper Assembly A — Tighten to 9-12 Nm (80-106 Lb-In)

Feb 23, 2009 | 1998 Ford Windstar

1 Answer

Windshield wipers only raise 5 inches before returning


this is wher the park switch in the wiper motor is going bad.
im sorry to tell you its going to get worse and you will need to replace the wiper motor assembly. alot of good one at your local salvage yard for just a few dollars.
good luck
paul

Sep 28, 2008 | 1994 Oldsmobile Eighty Eight

2 Answers

Windshield wiper connector


The grooves on the motor shaft got worn out or something that holds the wiper shaft to the motor broke. take off the wiper shaft and you have more or less an idea what it could be.it is obviously not the motor.

Jun 03, 2008 | 1997 Nissan Sentra

Not finding what you are looking for?
1993 Nissan Maxima Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...