Question about 2001 Jeep Cherokee

2 Answers

Need torque specs for a 2001 jeep cherokee intake manifold

Posted by on

  • 1 more comment 
  • crabbbitch May 07, 2010

    well husband went away i was asking for him...... all i know is the 2001 only came in a 4.0

  • crabbbitch May 07, 2010

    4.0

  • yadayada
    yadayada May 11, 2010

    what engine

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Jeep Master
  • 75,807 Answers

Attached is the picture of the torque sequence for bolts and the torque specs. as u can see different bolts have diff specs for torque


need torque specs for a 2001 jeep cherokee intake - c45631a.jpg

Posted on May 07, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 17,970 Answers

Intake manifold using new gaskets. Torque the bolts, in sequence, to 105 inch lbs. (12 Nm)...

need torque specs for a 2001 jeep cherokee intake - 6a7ecad.jpg

Fig. Intake manifold torque sequence-3.7 & 4.7L engines


Hope this help (remember comment and rated this).

Posted on May 07, 2010

  • ZJ Limited
    ZJ Limited May 07, 2010


    4.0L Engine


    Tighten the fasteners in sequence and to the specified torque:
    - Fastener Numbers 1 through 5 - Tighten to 24 ft. lbs. (33 Nm).
    - Fastener Numbers 6 and 7 - Tighten to 23 ft. lbs. (31 Nm).

    - Fastener Numbers 8 through 11 - Tighten to 24 ft. lbs. (33 Nm)


    Using a new exhaust manifold seal, connect the exhaust pipe to the
    engine exhaust manifold. Tighten the bolts to 23 ft. lbs. (31 Nm).




    Fig. The intake and exhaust manifolds torque sequence for the
    1999-01 models


    Good luck.

×

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 56 Answers

SOURCE: what is the torque specs on intake and manifold

best bet is to get a book. It might take degree along with torque.

Posted on Mar 07, 2010

arauzvictor1
  • 466 Answers

SOURCE: need head bolt, intake manifold, and exhaust torque specs

Cylinder Head Bolt Step1- (25 FT.Lbs) Step2(45 Ft.Lbs) Step3(65Ft,Lbs).....Intake Manifold(35Ft Lbs)....Exhaust Manifold Center (20Ft Lbs) All Others (20 Ftlbs).....Thanks

Posted on Mar 06, 2010

  • 2926 Answers

SOURCE: what is the intake and manifold bolts torque specs

What size engine?

Posted on Mar 07, 2010

2coolrick
  • 560 Answers

SOURCE: what is the torque specs on intake and manifold

Call Autozone or a major parts retailer. They will give you the torque/tightening sequence for free.

Posted on Mar 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOW TO FIX A BLOWN HEAD GASKIT?


Buy a gasket kit for the upper end. Remove the valve cover intake and exhaust manifolds. Remove the head bolts. Remove head and clean up block from old gasket material. Take the head to a machinist and make sure that it is not warped. If it is warped either replace the head with a new one or have it machined true. Install new gasket and get torque specs with new head bolts and follow torque sequence using the correct torque specs. Clean exhaust, intake and valve cover of old gaskets. install new gaskets and torque according to specifications.

Nov 27, 2010 | 1993 Jeep Cherokee Country

1 Answer

What are the torque specs for replacing the exhaust manifold and intake manifold gasket?


check the diagram below it is all there, different bolt positions have different torque settings, do this exactly as shown or you will have problems again.


emissionwiz_15.jpg

Nov 11, 2010 | 1994 Jeep Grand Cherokee

2 Answers

Need torque specs for 2000 chevy malibu 3.1 cyl heads & intake


(step 1 ) the torque specs for the heads are---1998 through 2001 are 37 foot lbs. ( step 2) rotate an additional 90-degrees (1/4 turn). intake manifold bolts ( lower ) step 1-- 62 in-lbs, step 2--115 in-lbs. intake manifold bolts/studs ( upper ) 18 ft-lbs. this is for the 3.1 v-6, have a good day!

Aug 14, 2010 | 2000 Chevrolet Malibu

1 Answer

What is the torque specs on intake and manifold bolt on a 2001 jeep cherokee engine is 4.0


best bet is to get a book. It might take degree along with torque.

Mar 07, 2010 | 2001 Jeep Cherokee

1 Answer

What is the torque specs on intake and manifold bolt on a 2001 jeep cherokee engine is 4.0


Call Autozone or a major parts retailer. They will give you the torque/tightening sequence for free.

Mar 07, 2010 | 1993 Jeep Grand Cherokee

1 Answer

Need torque spec & sequence for 89 cherokee 4.0L intake/exh manifold


If you run around 30ft/lb it will be ok.Start from the middle and work outward in the tightening of the manifolds.The bolts need to have an anti-seeze on the them and very lightly put some grease on the gaskets.This helps them settle on the initial tighten up.After about 1 hour of running,retighten them all.Hope this helps

Oct 28, 2009 | 1999 Jeep Cherokee

2 Answers

What is the torque specs for a 1998 jeep Cherokee classic straight 6 4.0 liter? I am replacing the head gasket and need to find the lbs of torque. Thank you for any advice, pictures, etc.


Torque sequence ------------------ front | 12 8 4 1 5 9 13 | of | | engine | 11 7 3 2 6 10 14 | ------------------ Final torque must be reached in 3 equal steps Step 1: torque all bolts (except bolt 11) to 110 Ft/Lbs Step 2: torque bolt 11 to 100 Ft/Lbs Recheck final torque in sequence.

  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Disconnect the hoses at the thermostat housing.
  4. Properly relieve the fuel system pressure.
  5. Remove the cylinder head cover.
  6. Loosen the rocker arms.
  7. Remove the pushrods.

The valvetrain components must be replaced in their original positions.
  1. Remove the intake and exhaust manifold from the cylinder head.
  2. Disconnect the spark plug wires and remove the spark plugs.
  3. Disconnect the temperature sending unit wire, ignition coil and bracket assembly from the engine.
  4. Remove the accessory drive belt(s).
  5. Unbolt and set aside the power steering pump and bracket. Do not disconnect the hoses.
  6. Remove the intake and exhaust manifold assembly.
  7. If equipped with A/C, perform the following:
    1. Remove the compressor and position it aside with the lines attached.
    2. Remove the compressor bracket bolts from the cylinder head.
    3. Loosen the through bolt at the bottom of the bracket.

  8. Remove the alternator.
  9. Remove the cylinder head bolts, the cylinder head and gasket from the block.

Bolt No. 14 cannot be removed until the head is moved forward. Pull the bolt out as far as it will go and suspend in place by wrapping with tape.
  1. Discard the gasket. Thoroughly clean the head-to-block mating surface.
  2. Clean and inspect the cylinder head thoroughly. Refer to the engine reconditioning portion outlined later in this section.

To install:
  1. Coat a new head gasket with suitable sealing compound and place it on the block. Most replacement gaskets will have the word TOP stamped on them.

Apply sealing compound only to the cylinder head gasket. Do not allow sealing compound to enter the cylinder bore.

Oct 08, 2009 | 1998 Jeep Cherokee

Not finding what you are looking for?
2001 Jeep Cherokee Logo

4,169 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...