Question about 2000 Pontiac Grand Prix

1 Answer

Changed the gas cap,evap canister, and the vent solenoid and light comes back on with same code what else could possibly be wrong?

Posted by on

  • yadayada
    yadayada May 11, 2010

    what is the code? was the gas tank pressure sensor replaced?

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 645 Answers

You need to check the vacuum hoses and fittings going back to the gas tank. you have to make sure there are no cracks in the hoses and make sure all the connectors have good o rings. leave comment

Posted on May 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007. What are the probable causes of DTC P0446?


DTC P0446: Evaporative Emissions (EVAP) Vent System Performance
Circuit/System Description
This DTC tests the evaporative emission (EVAP) system for a restricted or blocked EVAP vent path. The control module commands the EVAP canister purge solenoid valve Open and the EVAP canister vent solenoid valve Closed. This allows vacuum to be applied to the EVAP system. Once a calibrated vacuum level has been reached, the control module commands the EVAP canister purge solenoid valve Closed and the EVAP canister vent solenoid valve Open. The control module monitors the fuel tank pressure (FTP) sensor for a decrease in vacuum. If the vacuum does not decrease to near 0 inch H2O in a calibrated time, this DTC sets.
Diagnostic Aids
?€¢
An intermittent condition could be caused by a damaged EVAP vent housing, a temporary blockage at the EVAP canister vent solenoid valve inlet, or a pinched vent hose. A blockage in the vent system will also cause a poor fuel fill problem.


?€¢
An EVAP canister, vent hose, or vent solenoid valve that has restricted flow may cause this DTC to set. Using a purge solenoid command with a scan tool will allow vacuum to be applied to the system instead of pressure. With the engine running, the EVAP canister vent solenoid valve open, and the EVAP canister purge solenoid valve commanded to 100 percent, the fuel tank vacuum should not increase to more than 5 inches H2O.


?€¢
An EVAP canister filter that is restricted can cause this DTC to set. Refer to Evaporative Emission Canister Replacement .


?€¢
Disconnecting one component at a time while the EVAP system is under flow will help to pinpoint a restriction in the system


Do you have a scan tool that reads data PID'S ?
Your FTP - fuel tank pressure sensor could be at fault !

    Ignition ON and fuel cap removed, verify that the FTP sensor parameter is between 1.3-1.7 volts. ?‡'
    If not within the specified range, go to the FTP sensor section in Circuit/System Testing.

  1. Install the fuel cap.
  2. With the engine running, the EVAP canister vent solenoid valve open, and the EVAP canister purge solenoid valve commanded to 100 percent, the fuel tank vacuum should not increase to more than 12 inches H2O.
?‡'
If the fuel tank vacuum is greater than the specified range, go to the restriction section in Circuit/System Testing.



If

Sep 06, 2015 | Chevrolet Impala Cars & Trucks

2 Answers

I would like to know what the code PO455 on a 2007 Mitsubishi Endeavor means.


Possible causes
- Missing or loose fuel cap
- Incorrect fuel filler cap used
- Fuel filler cap remains open or fails to close
- Foreign matter caught in fuel filler cap
- EVAP canister or fuel tank leaks
- EVAP system hose leaking
- Fuel tank leaking
help.jpg What does this mean? Tech notes
The P0455 it's a very common code, because the code is set if the gas cap is loose or missing. Start by tighten the gas cap and clearing the code. In most cases the code can be clear by disconnecting the car battery for about 30 minutes.
help.jpg What does this mean? When is the code detected?
Evaporative Emission System (EVAP) control system has a very large leak such as fuel filler cap fell off, EVAP control system does not operate properly.
Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Possible a noticeable fuel odor caused by the release of fuel vapors
P0455 Mitsubishi Description
This diagnosis detects leaks in the Evaporative Emission System (EVAP) purge line using engine intake manifold vacuum. If pressure does not increase, the Engine Control Module (ECM) will check for leaks in the line between the fuel tank and EVAP canister purge volume control solenoid valve under the following vacuum test condition.
The vacuum cut valve bypass valve is opened to clear the line between the fuel tank and the EVAP canister purge volume control solenoid valve. The EVAP canister vent control valve will then be closed to shut the EVAP purge line off. The EVAP canister purge volume control solenoid valve is opened to depressurize the EVAP purge line using intake manifold vacuum. After this depressurization is implemented, the EVAP canister purge volume control solenoid valve will be closed.

Read more: http://engine-codes.com/p0455_mitsubishi.html#ixzz3NlVyARyX

3022.gif

Dec 30, 2014 | Cars & Trucks

1 Answer

Computer code 455


Possible causes - Missing or loose fuel cap
- Incorrect fuel filler cap used
- Fuel filler cap remains open or fails to close
- Foreign matter caught in fuel filler cap
- EVAP canister or fuel tank leaks
- EVAP system hose leaking
- Fuel tank leaking The P0455 it's a very common code, because the code is set if the gas cap is loose or missing. Start by tighten the gas cap and clearing the code. In most cases the code can be clear by disconnecting the car battery for about 30 minutes.

When is the code detected? EVAP control system has a very large leak such as fuel filler cap fell off, EVAP control system does not operate properly. Possible symptoms - Engine Light ON (or Service Engine Soon Warning Light)
- Possible a noticeable fuel odor caused by the release of fuel vapors P0455 Buick Description This diagnosis detects leaks in the Evaporative Emission System (EVAP) purge line using engine intake manifold vacuum. If pressure does not increase, the Engine Control Module (ECM) will check for leaks in the line between the fuel tank and EVAP canister purge volume control solenoid valve under the following vacuum test condition. The vacuum cut valve bypass valve is opened to clear the line between the fuel tank and the EVAP canister purge volume control solenoid valve. The EVAP canister vent control valve will then be closed to shut the EVAP purge line off. The EVAP canister purge volume control solenoid valve is opened to depressurize the EVAP purge line using intake manifold vacuum. After this depressurization is implemented, the EVAP canister purge volume control solenoid valve will be closed.
if tightening the cap or replacing the cap does not help take your car to a shop to have it diagnosed as it requires special tools/equipment to test this and get an accurate results to find what needs replacing.

Oct 10, 2014 | 2004 Buick LeSabre

1 Answer

My 00 xterra had a code of po446


Trouble Code: P0446

EVAP Vent Control Solenoid Circuit Malfunction

Possible Causes:


Vent solenoid circuit open, shorted to ground or to power (B+).Vent control solenoid is damaged or has failed..PCM has failed.TSB 00-060 (7/00) contains information related to this code.Trouble Code: P0455

EVAP System Gross Leak (0.080") Detected

Possible Causes:


.EVAP control system pressure sensor is damaged or has failed.EVAP purge solenoid or canister vacuum line loose or off.EVAP purge solenoid is damaged or has failed.EVAP emission canister is dirty, restricted or full of water.EVAP canister vent control valve is damaged or has failed.Fuel tank cap loose, missing or it is the wrong part number.Fuel tank temperature sensor is damaged or has failed.Fuel tank vacuum relief valve is damaged or has failed.Large leak in the EVAP canister or in the fuel tank area.ORVR system is damaged or has a large leak in a component.Refueling control valve is damaged or has failed.Vacuum hose leaking between intake manifold and Purge valve.Here are the codes,take part back and get refund.

Dec 03, 2012 | Cars & Trucks

2 Answers

1st code p0440, then code p0453 then p0452 now p0446


This problem is out side the gas tank , has nothing to do with the fuel pump or fuel level sending unit inside the gas tank .DTC P0446 EVAP Vent Solenoid Valve Control System . Do you know anything about automotive evaporative emission system ?
Wells EVAP Training with Sgt Tech P0440 P0441 P0442 etc

This DTC tests the evaporative emission (EVAP) system for a restricted or blocked EVAP vent path. The control module commands the EVAP canister purge solenoid Open and the EVAP canister vent solenoid Closed. This allows vacuum to be applied to the EVAP system. Once a calibrated vacuum level has been reached, the control module commands the EVAP canister purge solenoid Closed and the EVAP canister vent solenoid Open. The control module monitors the fuel tank pressure (FTP) sensor for a decrease in vacuum. If the vacuum does not decrease to near 0 inches H2O in a calibrated time, this DTC sets.

Mar 13, 2017 | 2000 Cadillac DeVille

2 Answers

Obd code p0457 fuel cap replaced mil reset defect not cleared connection checked ok


The code is for a large leak in the EVAP system such as a loose or missing gas cap. But it could also mean a loose or missing hose to the canister or other leak in the tank.
The computer vents the tank several times an hour while the engine is running, and it checks the system by pressurizing the gas tank. If the tank will not hold pressure the code is set.
You may have to check the top of the tank where the fuel pump gasket is, as well as the vent lines to the front of the car.
A mechanic would perform a smoke test to look for leaks.

Jul 23, 2012 | Honda Accord Cars & Trucks

1 Answer

2000 Ford Focus...DTC code PO455


code PO455
EVAP Control System Large Leak Detected
Possible Causes:


Aftermarket EVAP hardware non-conforming to specifications Canister vent (CV) solenoid stuck open EVAP canister purge valve stuck closed, or canister damaged EVAP canister tube, EVAP canister purge outlet tube or EVAP return tube disconnected or cracked, or canister is damaged Fuel filler cap missing, loose (not tightened) or the wrong part Loose fuel vapor hose/tube connections to EVAP components Purge sensor or FTP sensor is out of calibration or has failed I would say that your gas cap is a good place to start.

Apr 25, 2012 | 2000 Ford Focus

1 Answer

Check engine light initially showed code for speed sensor,changed that & light came back on,now shows code 440 & 600,tried tightening gas cap & still comes on


Unfortunately the P0440 code could be a comdination of about 4 different possibilities within the EVAP System:

1. Fuel Cap loose or Not holding proper pressure causeing a leak in the EVAP System
2. EVAP Canister Purge Volume Control Valve
3. EVAP Canister Purge Control Valve
4. EVAP Canister Vent Control Valve

The Vent Control Valves are common for going bad and causing leaks in the EVAP System.

Now, the P0600 Code - ECM recieving incorrect voltage from A/T control Unit Continuously.

Unfortunately, my suggestion to you would be to take the vehicle to your local Nissan Dealer where they have the appropriate scan tools to monitor the EVAP System and the Transmission control System.

Hope this helps...

Sep 17, 2011 | 1997 Nissan Maxima

2 Answers

Location of sensor for troubleshooting po442 to cause check engine light to come on


P0442 OBD-II Trouble Code - Evaporative Emission Control System Leak Detected (small leak)

What does that mean?
This indicates a fuel vapor leak in the EVAP control system. It means a very small leak has been detected. In fact, the leak can be from a hole as small as 0.04" in diameter. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.


Symptoms
You likely won't notice any drivability problems.


Causes
A code P0442 most likely means one or more of the following has happened:
* A loose or improperly affixed gas cap
* A non-conforming gas cap (i.e. not factory/original brand)
* A small leak/hole in a fuel vapor hose/tube
* Other small leak in EVAP system
* Faulty vent o-ring seal


Possible Solutions
With a P0442, the most common repair is to:
* Remove and reinstall the gas cap, clear the codes, and drive for a day and see if the codes come back.
* Otherwise, replace the gas cap, or
* Inspect the EVAP system for cuts/holes in tubes/hoses


46b629a.jpg

Fig. EVAP vent solenoid (2) on 3.1L, 3.4L, 3.5L & 3.8L, showing the connector (1) and vapor line (2)


510065b.jpg

Fig. EVAP canister purge solenoid location on 3.1L & 3.4L


a193655.jpg

Fig. EVAP purge solenoid valve (3) location on 3.5L




Hope this help, good luck.

May 11, 2010 | 2002 Buick Century

1 Answer

My taurus failed due to code p0442 ecap emiss ctl sys leak detected (small leak)


    Continuous Memory Diagnostic Trouble Code (DTC) P0442 indicates that a fuel vapor leak has been detected [as small as 0.10 cm (0.04 inch)] in the Evaporative Emission (EVAP) system.
    Note: Prior to performing the following diagnosis inspect the Canister Vent Solenoid (CV) for contamination. A situation may exist where contamination holds open the Canister Vent (CV) solenoid enough to set DTC P0442 and also plugs the port to atmosphere enough to keep system from being vented quickly.
    • After market parts and accessories nonconforming to the EVAP system specifications.
    • Damaged, cross threaded or loosely installed fuel filler cap.
    • Small holes or cuts in fuel vapor hoses/tubes (EVAP canister tube, EVAP canister outlet tube or EVAP return tube) in the EVAP system.
    • Loose fuel vapor hose/tube connections to EVAP system components.
    • EVAP system component [EVAP canister purge valve, fuel tank pressure (FTP) sensor, canister vent (CV) solenoid, fuel vapor control valve tube assembly or fuel vapor vent valve assembly] seals leaking.
    • CV solenoid partially open when commanded closed.
    • EVAP canister leaking.
  • Check for presence of fuel filler cap.
  • Verify that the CV solenoid is properly seated on the EVAP canister (if possible).
  • Visually inspect for cut or loose connections to fuel vapor hoses/tubes in following locations:
    • EVAP canister to EVAP canister purge valve.
    • EVAP canister to fuel vapor vent valve assembly.
    • fuel vapor control valve tube assembly to fuel tank (if applicable).

Jun 26, 2008 | 1997 Ford Taurus

Not finding what you are looking for?
2000 Pontiac Grand Prix Logo

584 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...