Question about 2002 Chevrolet Blazer

1 Answer

How do I replace the distributor, cap and rotor?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 333 Answers

First of all get a piece of paper and draw it out. Label each wire where it go's back in the same place as it is. Then unplug all of them. At the base of the cap there is either two small bolts or screws. Take them out pull straight up on it and it will pop off. then the rotar button has two screws. And there should be grease that comes with rotar button. Make sure follow directions for that. Take em off replace it and cap. Then plug the wires back up. It all only go's one way except the wires.

Posted on May 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 92 passat GL that chuggs, jolts, then dies when I shift into 1st. The distributor cap falls down(still clipped in) trashing cap and rotor both. I've replaced cap and rotor 4 times in the last...


If the distributor cap falls down onto the rotor button then you have the wrong distributor cap and it is too big for your distributor. Run fault codes to check for accelerator position sensor fault and check MAP/MAF sensors.

Nov 02, 2013 | 1992 Volkswagen Passat

Tip

How to Replace a Distributor Cap in Toyota?


Its a plastic cap and and on its top the sparks wires get connected.A small plastic rotor spins inside the distributor cap, firing each spark plug as it rotates. If the distributor gets faulty there the engine may not perform well. in most cases it has been noticed that only replacing the cap does not helps but with cap the rotors also need to be replaced. The procedure is as follows:--- 1) First of all disconnect the negative battery terminal. 2) Then remove the spark-plug wires . Note:-- Before removing the spark plug wires please note down how and where the wires are connected,then only remove the connections. 3) Then on the distributor there will be a cap.remove that cap.the cap is connected by two pins.you will have to press the pins from each side to loosen the distributor cap.Then lift the distributor cap from the top. 4)Then remove the rotor From distributor The rotor is fitted with two screws.Remove the screws and loosen the rotor. 5) Then lift the rotor out from its shaft. 6) To install new rotor and cap.reverse the procedure. This will help.Thanks.

on Mar 25, 2010 | Toyota Corolla Cars & Trucks

1 Answer

Is it hard to change distributor on 2000 nissan pathfinder


Hi there;This is for a 2000 Nissan Truck Pathfinder 4WD 3.3L SFI 6cyl


Distributor Cap & Rotor - Removal & Installation


NOTE
The 1996-00 3.3L engines were equipped with a distributor.


Disconnect the negative battery cable.
If the distributor cap is to be replaced, mark the ignition wires for identification and remove them from the distributor cap.
Remove any components necessary to access the distributor cap.
Completely loosen the distributor cap mounting fasteners.
Carefully remove the distributor cap, taking care not to damage the cap seal or rotor, then position the cap aside.
If necessary, remove the rotor retainer.
Carefully lift the rotor off the distributor shaft.
NOTE
Inspect the distributor cap to housing seal for damage and/or cracks. Replace if cracks are detected.




To install:


Install the rotor onto the distributor shaft and tighten the rotor mounting fastener, if equipped.
Position the distributor cap seal on the distributor housing, then position the distributor cap on the housing.
Install the distributor cap by tightening the mounting fasteners in a crisscross pattern. Use care to not over-tighten the fasteners.
Reconnect the spark plug wires, making sure to install them exactly in the same position from which they were removed.
Reconnect the negative battery cable.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jun 06, 2012 | Nissan Pathfinder Cars & Trucks

2 Answers

I have a 1998 durango, I have no spark from disturbtor but have spark from coil


Replace the distributor cap and rotor. If you have fire from the coil but not from the distributor cap, you have a bad contact point between the cap and rotor. Replace both and you should be good to go,, if the information that you have supplied is correct.

Aug 21, 2011 | 1998 Dodge Durango

1 Answer

97 dodge stratus 2.5 car turns over but does not have spark. There is fuel. I replaced the ECM crankshaft position sensor.


I would start with the rotor and cap. I just worked on one and it was the distributor was bad.

If you need to remove it and rplace it heres how.

Distributor Removal and Installation REMOVAL
  1. Remove bolt holding air inlet resonator to intake manifold.
  2. Loosen clamps holding air cleaner cover to air cleaner housing.
  3. Remove PCV make-up air hose from air inlet tube.
  4. Loosen hose clamp at throttle body.
  5. Remove air inlet tube, resonator and air cleaner cover.
  6. Remove EGR tube.
  7. Remove spark plug cables from distributor cap.
  8. Loosen distributor cap hold-down screws and remove cap.
  9. Mark rotor position for installation reference, then remove rotor.
  10. Remove two harness connectors from distributor.
  11. Remove two sets of distributor hold-down nuts and washers from studs.
  12. Remove bolt and spark plug cable mounting bracket from top of distributor housing.
  13. Remove bolt and transaxle dipstick tube.
  14. Carefully remove distributor from engine.
INSTALLATION
  1. Install rotor on shaft.
  2. Position distributor in engine and ensure O-ring is properly seated on distributor. Replace O-ring if it is cracked or nicked.
  3. Carefully engage distributor drive with slotted end of camshaft. When the distributor is installed properly, the rotor will be in line with previously marked line on air intake plenum.
  4. If engine was cranked while distributor was removed, establish proper relationship between distributor shaft and No. 1 piston position as follows:
    1. Rotate crankshaft until number one piston is at top of compression stroke.
    2. Rotate rotor to No. 1 rotor terminal.
    3. Lower distributor into opening, engaging distributor drive with drive on camshaft. With distributor fully seated on engine, rotor should be under No. 1 terminal.
  1. Install distributor hold-down washers and nuts. Torque to 9 ft-lbs .
  2. Install spark plug cable bracket.
  3. Install two harness connectors to distributor.
  4. Install distributor cap.
  5. Install transaxle dipstick tube.
  6. Install EGR tube to intake manifold. Torque bolts to 8 ft-lbs .

Mar 06, 2011 | Dodge Stratus Cars & Trucks

1 Answer

I need to replace ,the rotor button...


TAG OR NUMBER ALL SPARK PLUG WIRES ON THE DISTRIBUTOR CAP BEFORE REMOVING CAP. SO YOU CAN PUT PLUGS WIRES BACK IN THE ORIGINAL POSITION. WHEN ALL PLUGS WIRES ON DISTRIBUTOR CAP BEEN NUMBER.REMOVE ALL PLUG WIRES ON CAP.THEN REMOVE THE DISTRIBUTOR CAP.THEN MARK ROTOR POSITION WITH SHARPIE MARKER THEN REMOVE THE ROTOR.

Mar 02, 2011 | Chevrolet 1500 Cars & Trucks

1 Answer

Remove the rotor


On the 2.0L motor, pop off the 2 clips on the distributor, holding the cap on, move the cap out of the way. Pull the rotor off the shaft. And press on the new one. Then remove the center coil wire from old cap, line up new cap to old cap, and transfer 1 wire at time to the new cap. There is a notch where the cap fits to the distributor housing, make sure you have the new cap, exactly like the old one, both notches at 3 o'clock, for insistance. Reinstall the cap with the notch mating the distributor housing slot, and snap on the clips.

Mar 16, 2010 | 1994 Volkswagen Jetta

1 Answer

How do i remove old rotor to replace with a new one


brake rotor or distributor rotor?

The brake rotor usually gets rusted on....putting a hammer on one portion of the rotor face and striking the rotor face 180 degrees from the first hammer should do it.

Distributor rotor is under the distributor cap. Two screws usually free the cap and expose the rotor. You pull off the old one and push on the new one!

Good luck and be careful!

Feb 21, 2010 | 1991 Honda Accord

2 Answers

My 400e mercedes is misfiring,and I hear a small metal pcs crunchy sound around the distributor cap,do u think that the rotor cap is bad


Your distributor bushing is bad, causing the distributor to wobble when running. Get it checked out for repair and/or replace the distributor. Take off the cap and check the play in the shaft that the rotor is attached to first.

Jan 27, 2010 | 1993 Mercedes-Benz Mercedes Benz 400 Class

1 Answer

ROTOR BURNING UP


The rotor is somehow making direct contact with one or more distributor contacts.

Check the contacts inthe cap to see if you find any physical damage to one or more contacts caused by the rotor.

Could be rotor lead too long (file it down) or maybe the distributor shaft is bent or not seated. Remove cap and observe the distributor shaft as someone cranks the engine. Does it wobble? Can't tell? Place a stiff reference parallel to the shaft and turn engine again.

Oct 07, 2009 | 1996 Chevrolet Suburban

Not finding what you are looking for?
2002 Chevrolet Blazer Logo

Related Topics:

192 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...