Question about 2004 Chevrolet Blazer

1 Answer

Chevrolet engine fault code uo107 , please explain what this means , how can it be removed and problem solved

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Chevrolet Master
  • 3,640 Answers

Po107 map curcuit low input. to change map sensor is easy, usually 2 screws and a vacuum hose. differant on all vehicles. go to any auto parts store and they will tell ya where it is for your engine.

Posted on May 07, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

3 Answers

Service stabilitrac in 2009 gmc sierra

This light means that a fault has occurred in the electronics of the system, you must now have the system scanned by the dealer to see what fault codes are stored in the computers memory for the problem that turned on the warning light.

Jul 10, 2012 | 2006 Chevrolet Blazer

1 Answer

2005 equinox awd 21,000 mi UO107 fault code two engine symbols displayed when you attempt to start engine car will rev up then settle to idle no throttle control -ignition switch does not lock the ste

Your problem could be at the fuse panel. A cheap fix is to get some stranded wire. Small gauge, like 24 or 32 gauge. Cut small pieces and strip the ends and put them down in the fuse panel where the relay goes. Then put the relay in. If this doesn't cure the problem, look to the throttle body plug. best to replace the plug. If the wire woks for the panel, Leave it or replace the fuse panel.

Apr 09, 2017 | Cars & Trucks

1 Answer


The unique way to know what means this warning is scanning the PCM (Powertrain Control Module); visit Autozone or AutoShop with OBD scanner reader and note this fault code.

With this code number could send additional details to diagnostic and solve it. Keep in touch.

Sep 22, 2011 | 2009 Chevrolet Aveo

4 Answers

When I start my car the "check engine light" stays on. Its running fine and all the fluid levels are fine.

Some fault code is stored in the PCM (computer), generally could be some emissions code, but to know excalty what faulto code is, you need scanned the PCM. Some Autozone or Autoshop with scanner reader sometimes make this job for free.

Hope helps

May 28, 2011 | 2006 Ford Taurus

1 Answer

What does it mean when my check engine light goes on?

If the check engine light is On that means there is a error code got set in the cars computer.Get your car scanned at auto-zone for knowing the exact fault code.The error will indicate the exact fault causing the engine light to remain ON.At autozone service center its free to get car scanned.-------- That's it.

Nov 20, 2010 | 2006 Chevrolet Tahoe

1 Answer

On a 1998 Chevrolet truck, K1500, 350 engine, I have a dead miss.

if you are getting a CKP (crankshaft position sensor) code, and during you rebuild you had removed the sensor of moved it in any way, you probably need to perform a CKP sensor relearn. check with your local shops, as they need to be set up to do this, but it is not an expensive thing.

Dec 28, 2009 | 1998 Chevrolet K1500

2 Answers

Code drive 5 . My 2004 trailblazer posted a code "drive 5". It showed the "reduced engine poweer" light, and would not respond to the accelerator pedal. I had been driving in slow traffic. I pulled over,...

Thottle body sensor, accelerator pedal sensor, restricted air flow...will all trigger this fault light. Go to your local Autozone, they will run an OBD scan for free, and explain the fault codes to you so the correct repairs can be made.
Good luck...i hope this helps, please rate me a fixya.

Jul 22, 2009 | 2004 Chevrolet TrailBlazer

3 Answers

3 codes po303,uo101,uo107

break down of the codes is

po303 - that would be a misfire on cylinder 3
uo101 - cant communicate with TCM
uo107 - lost communication with throttle actuator control module

Feb 26, 2009 | 2005 Chevrolet Equinox

Not finding what you are looking for?
2004 Chevrolet Blazer Logo

Related Topics:

921 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

80417 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides