Question about 1997 Toyota Celica

1 Answer

Need to replace the passenger rear wheel bearing. Is it a bolt on part or do I need to press the bearing in?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,309 Answers

Unless you have a bearing puller you are out of luck

Posted on May 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 83 Bronco 351w I am doing the brakes and the passenger side rotor needs to be replaced can someone walk me through this thanks


Personally I would replace both rotors to prevent a future brake imbalance.

* chock rear wheels, raise front of vehicle and place on stands.

* remove wheels, remove brake calliper and bracket assemblies.

* remove bearing hubs from axles, via removal of bearing adjustment nut

*remove hub seals, clean and inspect bearings, repack with HT bearing grease.

* the brake rotor bolts to the rear of the hub, you will have to remove and replace rotor to hubs, make sure all bolts are thread locked with loctite 263 and tensioned to spec.

* pack hub with grease, install seals, fitt hub assembly and adjust wheel bearing preload, install new split pins.

* fitt brake calliper and brackets, fit new brake pads,

* fitt wheels lower vehicle, test brake for function

Hope this helps..

Aug 02, 2016 | Cars & Trucks

3 Answers

2007 ford sport trac rear wheel bearing replacement


Jeff is describing how to replace the front wheel bearings. In the front, the bearing is part of a "hub cartridge". Randy is describing how to change the rear bearings on a truck with a "dead" rear axle. The sort of differential which is one massive cast iron assembly from rim to rim. However, your truck has an IRS [Independent Rear Suspension] design. You need to remove the wheels, brakes & the complete rear knuckle assembly. To remove the bearing from the knuckle requires a hydraulic press and a "knife edge" bearing removal tool. I doubt that you have these tools available. If not, find an auto parts store or auto machine shop with these tools. They can press the old bearing out and install the new one for you. Then you can reassemble the knuckle assembly from that point on. The video linked below should help you.


Ford Explorer Independent Rear Suspension Rear Wheel Bearing and Hub...


With the knuckle off, you can easily replace the ball joints at the same time. Odds are you will ruin the original ball joints getting the knuckle assembly off, anyway.

Jan 11, 2015 | 2007 Ford Explorer Sport Trac

1 Answer

Replace wheel bearing


which wheel bearing front rear on the front with front wheel drive you will need to remove the steering knuckle and then press the bearing out with a shop press then press hub back in to bearing on the rear it is most likely a bolt in easy

May 28, 2013 | 1989 Cadillac Sedan DeVille

1 Answer

Rear bushing removal 05 ford escape


can you post a picture please

Dec 21, 2012 | 2005 Ford Escape

1 Answer

How to replace rear wheel bearing on 2003 hyandia sonata


Hub & Bearing Removal & Installation To Remove:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Release parking brake.
  2. Remove rear wheel assembly.
  3. Remove rear wheel speed sensor from carrier.
  4. Dismount brake caliper and support with mechanic's wire.
  5. Remove brake disc.
  6. Remove 4 axle hub mounting bolts. Special tool 09432-11000 (Typical) hyundai-08-00-6021.gif

  7. Using tool 09432-11000 (or suitable gear puller), remove tone wheel.
  8. Remove carrier.
  9. Remove stakes and remove flange nut.
  10. Support bearing outer race flange and press rear axle hub out.
  11. Using tool 09432-11000 (or suitable puller), remove inner race from axle hub.
To Install:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Apply thin coat of grease to bearing contact surface and hub.
  2. Using and appropriate tool, press bearing into hub. CAUTION
    Do not press against outer race of wheel bearing.
  3. Install flange nut and stake nut until it meets concave portion of spindle.
  4. Install carrier.
  5. Use an appropriate tool to press tone wheel.
  6. Install hub/bearing assembly with rounded portion of outer race facing up.
  7. Install 4 hub/bearing assembly bolts and rotate hub to seat bearing.
  8. Measure wheel bearing starting torque with a spring balance or equivalent device.
    • Starting torque should measure 15.9 in lb (1.8 Nm) or less
  9. Install brake disc.
  10. Mount brake caliper.
  11. Install rear wheel speed sensor to carrier.
  12. Install rear wheel assembly.
prev.gif next.gif

Oct 28, 2010 | 2001 Hyundai Sonata

2 Answers

Passenger rear wheel bearng needs to be replaced.does this require special tools? I've just had a complete brake job ,new pads new rotors new drums and I have a recurring grinding noise coming from the...


You can do this job your self with common tools. Auto zone carries the wheel bearing you need and can give you the step by step instructions to replacing the bearing. Here is a tip, to try to break the old wheel bearing from the axle. Just loosen the 4 bolts 3 mm that hold the bearing to the axle and put the wheel back on and drive the car back and forth a few times, hard on the brakes to break it free from the axle. Once the bearing breaks free from the axle, it should take you under 45 min to get the job done. Good luck and be safe.

Nov 17, 2009 | 2001 Toyota Corolla

1 Answer

I need to fix the rear passenger side wheel bearing on my 2002 corolla but i would like to take it apart so i dont have to buy the entire assembly.


The rear wheel bearings is a bolt in hub unit and is not separately serviceable on this car.

Any attempt to replace just the bearing will have to involve pressing the bearings out then taking them to local bearing suppliers and having replacement units sourced or made based on the dimensions, as their are no correct listings available for this application.
The cost would far exceed the $300 for the hub, and quickly.

Oct 17, 2009 | 2002 Toyota Corolla

1 Answer

Loose rear wheel, believe it is the bearing. How do I repair it?


drum brakes you remove rear wheel- speed sensor-grease cap-flange nut-outer bearing-brake drum-inner grease seal-inner bearing-drive the bearing races out of the drum hub.to install -install the inner and outer bearing races.apply grease to the bearings and hub cavity.then you install the inner bearing -inner grease seal-brake drum-outer bearing-flange nut torque it to 159 to 192 ft lbs. THE REAR DISC BRAKE WHEEL BEARINGS-you have to remove rear wheel -wheel speed sensor-brake caliper and rotor-rear axle hub bolts-tone the wheel with tool 09445-21000-carrier assembly-nut after unstaking it-press out the rear axle hub-remove the bearing inner race with tool 09445-21000-remove the bushings from the carrier with tools 09453-33000b and 09545-21100.to install -press in the bushings to the carrier with tools 09453-33000b and 09545-21100- press in the bearings to the hub with tool 09221-21000.tighten the flange nut to meet the concave portion of the spindle-press in the tone wheel with tool 09221-21000-torque the nut to 191 ft lbs -install the hub and bearing assembly to the backing plate and torque the bolts to 88 ft lbs-install the brake caliper and rotor.install the wheel speed sensor if equipped.install the rear wheel.TO BUY THE TOOLS TO DO THE JOB.LOOK UP KENT MOORE TOOLS ON INTERNET.

May 30, 2009 | 1999 Hyundai Sonata

1 Answer

NEED TO REPLACE WHEEL HUB BEARING OR ONLY THE BEARING


Front Is pressed into hub & knuckle.Rear is a Hub/Bearing Assembly held in by 4 10mm bolts.Will need to pound out with hammer in rear after bolts come out,lots of rust holding them in.Front Knuckle has to come off,Then a large Snap ring,then press out the hub,then the wheel bearing.Hope this helps

May 19, 2009 | 1996 Saturn SL

Not finding what you are looking for?
1997 Toyota Celica Logo

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...