Question about 2006 BMW 750Li

3 Answers

How to reset passenger air bag/seat belt restraint light indictor on a 05 BMW 745LI.Makes the light goes off! Thanks, Mr.Raybo

Posted by on

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,472 Answers

It may be the seat mat sensor as this is a known problem. I would take it to the dealership to have it looked at as this is a safety issue.
Thank you,
Lee

Posted on May 07, 2010

  • Lee A.
    Lee A. May 07, 2010


    Hi,
    If this is the first time you have had this message you will need to take it to the dealership to have them reset it.
    Thanks,
    Lee



×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • BMW Master
  • 75,066 Answers

If the airbag light (SRS Warning Indicator) is on then there is a failure of some part of the system, the light will not reset until that is fixed, it is what is called a "CONTINOUS MONITOR SYSTEM" so this means it tests itself every few seconds when every the key is turned to run, so the light can not be reset until u have the system tested and find out what fault code it has in memory and then diagnose and find the problem that set the fault code and turned the light on, it is set up this way for your safety..

Posted on May 07, 2010

  • yadayada
    yadayada May 07, 2010

    what answer are you looking for here?, have been doing this type of work for 35 years, my answer is 100% correct.

  • yadayada
    yadayada May 07, 2010

    If u would like more info on this please call me at home, 925-577-7157

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,489 Answers

If the light is staying on, this is telling you that there is a problem within the system and needs to be scanned for codes. It should be taken in to a BMW dealership for this. If there is any TSBs for reflashing or replacement of a part they will know and since this would be considered a safety item, it tends to remain under warranty longer until the problem is resolved. Let me know what they say.

Posted on May 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 ford f-350 passenger air bag flashes 1-7 code than stays on when truck is started.What does the code mean and can the code be reset without tearing air bag out of truck?


If a SRS fault exists, the RCM sends a message to instrument cluster module to flash a coded sequence which is called a lamp flash code (LFC) on the air bag warning indicator. Each LFC is flashed 3 times after which the air bag indictor will remain lit for the remainder of the key-on cycle. In addition to the self-test at start up, the RCM continuously monitors all of its external and internal circuitry for faults.
While the LFCs are an indication of a general concern in the supplemental restraint system (SRS), the DTCs are more specific. The DTCs can be retrieved from the RCM with a scan tool via the DLC.


DTC a c LFC b Description Action To Take - Continuous Lamp The Air Bag Warning Indicator is Illuminated Continuously (RCM Disconnected or Inoperative, Loss of Battery Feed or Loss of Signal Ground) Go To Pinpoint Test A . B1048 c - Passenger Side Air Bag Cross Link to Another Firing Loop Go To Pinpoint Test B . B1049 c - Passenger Seatbelt Pretensioner Cross Link to Another Firing Loop Go To Pinpoint Test C . B1054 c - Driver Seatbelt Pretensioner Cross Link to Another Firing Loop Go To Pinpoint Test D . B1057 c - Driver Air Bag Cross Link to Another Firing Loop Go To Pinpoint Test E . B1231 13 RCM Crash Data Memory Full INSTALL a new RCM and CARRY OUT programmable module installation (PMI). REFER to Restraints Control Module (RCM) and Inspection and Repair After a Supplemental Restraint System (SRS) Deployment in this section. B1317 Continuous Lamp Battery Voltage High REFER to Section 414-00 . B1318 Continuous Lamp Battery Voltage Low REFER to Section 414-00 . B1342 24 RCM is Faulted INSTALL a new RCM and CARRY OUT programmable module installation (PMI). REFER to Restraints Control Module (RCM) in this section. B1871 25 Passenger Air Bag Deactivate Module Fault Go To Pinpoint Test F . B1884 27 Passenger Air Bag Deactivation (PAD) Warning Lamp Circuit Failure Go To Pinpoint Test G . B1890 27 Passenger Air Bag Deactivation (PAD) Warning Lamp Short to Battery Go To Pinpoint Test H . B2292 33 Restraint System - Seat Belt Pretensioner Fault (Driver Pretensioner Circuit Fault) Go To Pinpoint Test I . B2292 34 Restraint System - Seat Belt Pretensioner Fault (Passenger Pretensioner Circuit Fault) Go To Pinpoint Test I . B2293 19 Restraint System - Air Bag Fault (Driver Front Air Bag Circuit Fault) Go To Pinpoint Test J . B2293 21 Restraint System - Air Bag Fault (Passenger Front Air Bag Circuit Fault) Go To Pinpoint Test J . B2296 42 Restraint System - Impact Sensor Fault Go To Pinpoint Test K . B2434 53 Driver Seat Belt Buckle Switch Circuit Short to Ground Go To Pinpoint Test L . B2435 53 Driver Seat Belt Buckle Switch Resistance out of Range Go To Pinpoint Test M . B2477 54 Module Configuration Failure This DTC indicates programmable module installation (PMI) has not been done to a newly installed module. CARRY OUT PMI. REFER to Section 418-01 . CLEAR the DTC. CARRY OUT the self-test. B2607 57 Harness/Configuration Mismatch This DTC indicates the RCM is configured incorrectly. CARRY OUT programmable module installation (PMI). REFER to Section 418-01 . CLEAR the DTC. CARRY OUT the self-test. If DTC is retrieved a second time, INSTALL a new RCM and CARRY OUT PMI. REFER to Restraints Control Module (RCM) in this section. B2691 53 Seat Belt Buckle Switch Circuit Fault, Front Driver's Side Go To Pinpoint Test N . C1414 29 Incorrect Module Design Level VERIFY RCM part number is correct for vehicle.
CARRY OUT programmable module installation (PMI). REFER to Section 418-01 . CLEAR the DTC. CARRY OUT the self-test. If DTC is retrieved a second time, INSTALL a new RCM and CARRY OUT PMI. REFER to Restraints Control Module (RCM) in this section. U0100 14 Lost Communication With ECM/PCM REFER to Section 418-00 to diagnose the communication concern. U2023 14 Fault Received From External Node REFER to Section 418-00 to diagnose the communication concern. U2050 14 No Application Present This DTC indicates programmable module installation (PMI) has failed. CARRY OUT PMI. REFER to Section 418-01 . CLEAR the DTC. CARRY OUT the self-test. If DTC is retrieved a second time, INSTALL a new RCM and CARRY OUT PMI. REFER to Restraints Control Module (RCM) in this section. a DTC: Diagnostic trouble code, retrieved using scan tool.
c Cross-link DTCs will be retrieved in pairs to identify the cross-linked components.
b LFC: Lamp fault code, flashed on air bag warning indicator.

Apr 18, 2017 | Ford Cars & Trucks

1 Answer

On my 05 ford five hunmdred the air bag light flashes 3 times then pauses and then flashes four times does this twice I think and stays on


Which light ? on the instrument cluster or the passenger side .
If a lamp fault code (LFC) is reported by the customer but is not present when the vehicle comes in for service, follow the Diagnostic Instructions procedure in this section to identify the intermittent DTC.

Lamp Fault Codes
When the restraints control module (RCM) detects a system fault, it will cause the air bag indicator to flash a coded sequence; a lamp fault code (LFC). The code is 2 digits. The first digit is flashed with a 0.5-second interval between pulses. There is a 2-second pause before the second digit is flashed which also has a 0.5-second interval between pulses. There is a 5-second pause between each display of an LFC.
Each LFC is flashed 3 times after which the air bag indictor will remain lit for the remainder of the key-on cycle. If there are multiple LFCs, each LFC will flash in order of priority. Lamp flash code 34

B2292 d 34 Restraint System - Seat Belt Pretensioner Fault (Passenger Pretensioner Circuit Fault) Go To Pinpoint Test R .
PINPOINT TEST R: LFC 33 AND 34/DTC B2292 - RESTRAINT SYSTEM - SEAT BELT PRETENSIONER FAULT NOTE: Most faults are due to connector and/or wiring concerns. Carry out a thorough Inspection and Verification before proceeding with the pinpoint test.
NOTE: The retractor pretensioner connector keying is different between vehicles. The retractor pretensioner connector shown in the following pinpoint test is equipped on the Five Hundred, the connector equipped on the Freestyle and Montego is similar.
Test Step Result / Action to Take R1 CHECK FOR CONTINUOUS OR ON-DEMAND DTCs
    WARNING: Restraint system diagnostic tools are for service only. Tools must be removed prior to operating the vehicle over the road. Failure to remove restraint system diagnostic tools could result in injury and possible violation of vehicle safety standards. WARNING: Do not handle, move or change the original horizontal mounting position of the restraints control module (RCM) while the RCM is connected and the ignition switch is ON. Failure to follow these instructions may result in the inadvertent deployment of the safety canopy and risk of personal injury. WARNING: Never probe the connectors on the air bag module. Doing so can result in air bag deployment, which can result in personal injury. WARNING: The safety belt pretensioner is a pyrotechnic device. Always wear safety glasses when repairing an air bag equipped vehicle and when handling a safety belt buckle pretensioner or safety belt retractor pretensioner. Never probe a pretensioner electrical connector. Doing so could result in pretensioner or air bag deployment and could result in personal injury. WARNING: Never probe the electrical connector on a safety canopy module. Doing so can result in safety canopy deployment. NOTE: If a seat equipped with a supplemental restraint system (SRS) component is being serviced, the SRS must be depowered. NOTE: After diagnosing or repairing an SRS, the restraint system diagnostic tools must be removed before operating the vehicle over the road. NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
  • Enter the following diagnostic mode on the diagnostic tool: On-Demand Self Test.
  • Enter the following diagnostic mode on the diagnostic tool: Flag DTC B2292/ Record All Flagged Faults.
  • Enter the following diagnostic mode on the diagnostic tool: Retrieve/Flag /Record Continuous DTCs.
  • Was DTC B2292 retrieved during the on-demand self test?
Yes
This is a hard fault. The fault condition is still present. This fault cannot be cleared until it is corrected and the DTC is no longer retrieved during the on-demand self test. GO to R2 .

No
This is an intermittent fault. The fault condition is not present at this time. Your best bet , take it to a qualified repair shop .



.

Feb 19, 2017 | 2005 Ford Five Hundred

3 Answers

What does the red symbol like a driver with a ball in front of him means on the dashboard


This is a air bag fault light .it comes on when you have a fault in the air bag system.

Feb 19, 2017 | Cars & Trucks

1 Answer

2006 lincoln town car air bag light is on 5 beeps 5 times


The five beeps - five times would indicate a code 55 , but factory service info only goes to code 53 .

  • Audible tone - DTCs retrieved
  • Air bag SRS system fault
  • REFER to DTC Priority Table.

Did your air bag light flash at all ? Apparently this will do flash the air bag light codes as well .
Symptom Chart Condition Possible Sources Action
  • Air bag warning indicator is illuminated continuously
  • Fuse
  • Damaged wiring, terminals or connectors
  • A faulty diagnostic connector
  • A faulted RCM
  • A faulty instrument cluster
  • Go To Pinpoint Test A .
  • Air bag indicator flashing
  • Air bag/pretensioner supplemental restraint system (SRS) fault
  • REFER to DTC Priority Table.
  • Audible tone - DTCs retrieved
  • Air bag SRS system fault
  • REFER to DTC Priority Table.
  • No communication with the restraints control module (RCM)
  • Fuse
  • Diagnostic tool
  • Data link connector (DLC)
  • A faulted RCM
  • Circuitry
  • Go To Pinpoint Test V .
LFC - light flash codes .
Restraints Control Module (RCM) Diagnostic Trouble Code (DTC) Table
DTC a LFC b Description Action To Take - Continuous The Air Bag Indicator is Illuminated Continuously, RCM Disconnected or Inoperative, Loss of Battery Feed, or Loss of Signal Ground Go To Pinpoint Test A . B1231 13 Crash Data Memory Full Install a new RCM and impact sensors. REFER to Inspection and Repair After a Supplemental Restraint System (SRS) Deployment . B1317 Continuous Battery Voltage High CHECK battery voltage; to be below 16 volts. REFER to Section 414-01 . B1318 Continuous Battery Voltage Low CHECK battery voltage; to be above 9.0 volts. REFER to Section 414-01 . B1342 12 RCM Is Faulted Install a new RCM. B1869 NONE
Continuous lamp
Secondary air bag warning sounds if another fault is present Lamp Air Bag Warning Indicator Circuit Open or Short to Ground Go To Pinpoint Test B . B1870 NONE
Secondary air bag warning sounds if another fault is present Air Bag Warning Indicator Circuit Short to Battery Go To Pinpoint Test C . B1891 53 Air Bag Tone Warning Indicator Circuit Short to Battery Go To Pinpoint Test D . B1892 53 Air Bag Tone Warning Indicator Circuit Open or Short to Ground Go To Pinpoint Test E . B1921 14 Air Bag Diagnostic Monitor Ground Circuit Open Go To Pinpoint Test F . B2292 33 Restraint System - Safety Belt Pretensioner Fault (Driver Pretensioner Circuit Fault) Go To Pinpoint Test G . B2292 34 Restraint System - Safety Belt Pretensioner Fault (Passenger Pretensioner Circuit Fault) Go To Pinpoint Test G . B2293 19 Restraint System - Air Bag Fault (Driver Front Air Bag Circuit Fault) Go To Pinpoint Test H . B2293 21 Restraint System - Air Bag Fault (Passenger Front Air Bag Circuit Fault) Go To Pinpoint Test H . B2294 24 Restraint System - Curtain Fault (Driver Side Air Curtain Circuit Fault) Go To Pinpoint Test I . B2294 25 Restraint System - Curtain Fault (Passenger Side Air Curtain Circuit Fault) Go To Pinpoint Test I . B2295 22 Restraint System - Side Air Bag Fault (Driver Seat Side Air Bag Circuit Fault) Go To Pinpoint Test J . B2295 23 Restraint System - Side Air Bag Fault (Passenger Seat Side Air Bag Circuit Fault) Go To Pinpoint Test J . B2296 42 Restraint System - Impact Sensor Fault (Front Impact Severity Sensor Circuit Fault) Go To Pinpoint Test K . B2296 43 Restraint System - Impact Sensor Fault (Driver Side Front Row Impact Sensor Circuit Fault) Go To Pinpoint Test K . B2296 45 Restraint System - Impact Sensor Fault (Driver Side Second Row Impact Sensor Circuit Fault) Go To Pinpoint Test K . B2296 44 Restraint System - Impact Sensor Fault (Passenger Side Front Row Impact Sensor Circuit Fault) Go To Pinpoint Test K . B2296 46 Restraint System - Impact Sensor Fault (Passenger Side Second Row Impact Sensor Circuit Fault) Go To Pinpoint Test K . B2434 51 Driver Safety Belt Buckle Switch Circuit Short To Ground Go To Pinpoint Test L . B2435 51 Driver Safety Belt Buckle Switch Circuit Resistance Out Of Range Go To Pinpoint Test M . B2438 52 Passenger Safety Belt Buckle Switch Circuit Short To Ground Go To Pinpoint Test N . B2439 52 Passenger Safety Belt Buckle Switch Circuit Resistance Out Of Range Go To Pinpoint Test O . B2477 Continuous Module Configuration Error INSTALL a new RCM. B2691 51 Driver Safety Belt Buckle Switch Circuit Fault Go To Pinpoint Test P . B2692 52 Passenger Safety Belt Buckle Switch Circuit Fault Go To Pinpoint Test Q . C1414 15 Incorrect Module Design Level Go To Pinpoint Test R . C1947 49 Driver Seat Track Position Sensor Circuit Short to Ground Go To Pinpoint Test S . C1948 49 Driver Seat Track Position Sensor Circuit Resistance Out Of Range Go To Pinpoint Test T . C1981 49 Driver Seat Track Position Sensor Circuit Fault Go To Pinpoint Test U . - - No Communication with the Restraints Control Module Go To Pinpoint Test V . Your best bet have codes checked with a scan tool .

Jan 23, 2017 | Lincoln Cars & Trucks

1 Answer

Where is passenger side air bag relay 2007 MKZ


There is no relay for the passenger side air bag . What seams to be the trouble ? There is possibly a code set in the air bag control module .
Air Bag and Safety Belt Pretensioner Supplemental Restraint System (SRS) The air bag supplemental restraint system (SRS) is designed to provide increased collision protection for front seat and second row outboard occupants, in addition to that provided by the 3-point safety belt system. Safety belt use is necessary to obtain the best occupant protection and to receive the full advantage of the SRS.
This vehicle line contains dual stage deployment (advanced restraint system) driver and front passenger air bag modules. These vehicles are also equipped with driver and front passenger safety belt retractor pretensioners. These vehicles can also be equipped with optional side air curtains that deploy from the A-pillar to the C-pillar upon a side impact. Vehicles with optional side air curtains are also equipped with seat side air bag modules in the front seats.
Side air curtains deploy from the headliner, protecting the first and second row outboard occupants during a side impact. Seat side air bag modules deploy from the outboard front seat backrest upon a side impact. In addition, a front impact severity sensor is mounted to the lower radiator support, a seat position sensor is mounted to the driver seat and a usage detection switch is added to the front driver and passenger outboard buckles. If equipped with optional side air curtain modules and seat side air bag modules, there are an additional 4 side impact sensors.
Vehicles are also equipped with an occupant classification sensor (OCS) system as part of the front passenger seat. The OCS system includes 2 OCS rails and an OCS module.
Passenger Air Bag Deactivation (PAD) Indicator
The passenger air bag deactivation (PAD) indicator is a visual indicator used to inform the front seat occupants of the passenger air bag deactivation state. The PAD indicator is a stand-alone lamp installed into the vehicle instrument panel in a position visible to each front seat occupant.
The restraints control module (RCM) controls the state of the PAD indicator through a direct hardwire connection, based on information provided by the occupant classification sensor (OCS) system. The PAD indicator is lit to indicate the passenger air bag module is disabled. An exemption to this is when the front passenger seat is determined to be empty and passenger safety belt buckle unbuckled, and therefore indication of a deactivated passenger air bag module is not necessary. In all other cases, the PAD indicator is unlit when the passenger air bag module is enabled.
When the ignition switch is in the ON position, the PAD indicator prove-out period is initiated by the RCM. The RCM briefly activates the PAD indicator to prove-out the indicator function and verify to the front occupants correct functional operation of the PAD indicator.
The PAD indicator will be lit/unlit within 1.0 to 1.5 seconds of a change of state from the OCS system.
When an OCS system fault is present, the RCM defaults the passenger air bag module to the last valid state received from the OCS system until the ignition switch is turned OFF. If the OCS system fault is still present when the ignition switch is turned ON, the RCM defaults the passenger air bag module to enabled regardless of the size of occupant in the front passenger seat. The PAD indicator will be unlit. For information on the OCS system, refer to Occupant Classification Sensor System in this section.
The following table indicates the passenger air bag status and the PAD indicator status based the size of the front outboard passenger occupant.

Oct 04, 2015 | 2007 Lincoln MKZ

2 Answers

Passenger air bag/seat belt restraint error message on 2006 750li


Unfortunately there is no easy Do It Yourself answer for this. You need to have a BMW specialist check out the code if there is a faulty sensor or if the computer system needs to be reset. You don't necessarily have to go to the dealer as there are independent shops who have certified BMW specialists or can refer you to one - sometimes, you can find one on Craiglist who can come out to you.

Sep 05, 2011 | 2006 BMW 750Li

2 Answers

SRS light


SRS if you didn't already know is your secondary restraint system (airbags)...... you can try resetting it by unhooking the battery for about ten minutes.... before you do that you may want to go down to autozone and have them scan the codes to see what it is showing.

May 23, 2009 | 2003 Chrysler Town & Country

2 Answers

My 2003 ford expo has a constant airbag light lit after starting the veh. I have a new sensor, can't figure out were 2put it.. Please help.


first, you need to read the Lamp Fault Code, LFC from the flashing light. Here's how:

Lamp Fault Codes
When the restraints control module (RCM) detects a system fault, it will cause the air bag indicator to flash a coded sequence: a lamp fault code (LFC). The code is two digits. The first digit is flashed with a 0.5 second interval between pulses. There is a 2 second pause before the second digit is flashed, which also has a 0.5 second interval between pulses. There is a 5 second pause between each display of an LFC.
Each LFC is flashed five times after which the air bag indictor will remain lit for the remainder of the key-on cycle. If there are multiple LFCs, each LFC will flash in order of priority.
-------------------------------------------------------
The fault could be in the air bag circuits, the canopy circuits, the pretensioner circuit on the seat belts, etc.
Report back with code.

here's some of system.

SECTION 501-20B: Supplemental Restraint System 2003 Expedition/Navigator Workshop Manual
DESCRIPTION AND OPERATION Air Bag and Safety Belt Pretensioner Supplemental Restraint System (SRS) The air bag supplemental restraint system (SRS) is designed to provide increased collision protection for front seat and second row outboard occupants in addition to that provided by the three-point safety belt system. Safety belt use is necessary to obtain the best occupant protection and to receive the full advantage of the SRS.
This vehicle line contains dual stage deployment (advanced restraint system) driver and front passenger air bag modules. These vehicles can also be equipped with optional safety canopies that deploy from the A-pillar to the C-pillar upon a side impact or if a rollover condition is detected. If equipped with safety canopies, a unique restraints control module (RCM) is used.
See the following illustration for deployable component location.
Air Bag and Safety Belt Pretensioner Supplemental Restraint System (SRS) Deployable Components a55c8c5.gif Item Part Number Description 1 611D10 Passenger air bag module 2 042D94 Passenger side safety canopy module 3 042D95 Driver side safety canopy module 4 61203 Driver safety belt buckle and pretensioner 5 043B13 Driver air bag module 6 14A664 Clockspring 7 61202 Passenger safety belt buckle and pretensioner

4ee7996.gif
Item Part Number Description 1 14B321 Restraints control module (RCM) 2 14B345 Second row, C-pillar side impact sensor 3 14B345 Second row, C-pillar side impact sensor 4 14B416 Driver seat track position sensor 5 14B345 Front row, driver door, side impact sensor 6 14B006 Front impact severity sensor 7 14B345 Front row, passenger door, side impact sensor

Apr 23, 2009 | 1997 Ford Expedition

1 Answer

Airbag light is on - 2003 Tiburon


section_closed.gif 2003 HYUNDAI TIBURON Recall ID from NHTSA: 02V290000 Auto Recall Date: NOV 05, 2002 Vehicle Component: SEAT BELTS:FRONT:BUCKLE ASSEMBLY Model Affected TIBURON Estimated Vehicles Affected: 7382 Recall Details Auto Recall Date: NOV 05, 2002

Vehicle Component: SEAT BELTS:FRONT:BUCKLE ASSEMBLY Estimated Vehicles Affected: 7382 Model Affected2003 HYUNDAI TIBURON

2003 Hyundai Tiburon Defect Summary:ON CERTAIN PASSENGER VEHICLES, THE DRIVER SEAT BELT BUCKLE WIRING COULD BE DAMAGED BY INTERFERENCE WITH THE DRIVER SEAT CUSHION HEIGHT ADJUSTER MECHANISM.

Defect Consequence:DAMAGED DRIVER SEAT BELT BUCKLE WIRING COULD CAUSE THE SEAT BELT WARNING LAMP OR THE SUPPLEMENTAL RESTRAINT SYSTEM (SRS) AIR BAG WIRING LAMP TO ILLUMINATE. IT COULD ALSO CAUSE THE AIR BAG FUSE (CAVITY NUMBER 5) TO OPEN, PREVENTING AIR BAG DEPLOYMENT. NONDEPLOYMENT OF AN SRS AIR BAG IN A CRASH WHERE AIR BAG DEPLOYMENT IS WARRANTED COULD INCREASE THE RISK OR SEVERITY OF INJURY IN A CRASH.

Remedy:DEALERS WILL INSTALL A NEW DRIVER SEAT BELT BUCKLE, IF NECESSARY, AND WILL PLACE A PROTECTIVE COVER OVER THE DRIVER SEAT BELT BUCKLE WIRING TO PREVENT DAMAGE FROM OCCURRING. OWNER NOTIFICATION BEGAN ON MARCH 24, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT HYUNDAI AT 1-800-633-5151.

Estimated Vehicles Affected: 7382

Notes: HYUNDAI MOTOR COMPANY 056

Dec 07, 2008 | 2003 Hyundai Tiburon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

4,331 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...