Question about Toyota Sienna

1 Answer

2001 toyota sienna 3.0 l no start no engine spark no noid light pulse has fuel pressure and will run (try) to start on gas in spray bottle

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,489 Answers

I would say that you either have an ignition module failure or, more likely, a CPS(Crank Position Sensor) failure. This will be located by the front of the motor. Given that you told me you have no "noid" light pulse, you obviously have some knowledge. Let me know what else you need(i.e. wiring diagrams, trouble code defs, etc.).

Posted on May 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On a 2004 dodge durango, 4.7l turns over but won't start. It did it 2weeks ago was told electrical problem n fixed. Did it again 3 days ago and it started without anyone doing anything to it the following...


Durangos are known for crank sensors to go bad. Make sure that your battery is fully charged so you know that isn't an issue. If you don't have the proper equipment, try this.. Your going to need someone else's help for this. Pull one of the spark plug wires, using a screwdriver, put the tip of the screwdriver into the wire and hold the shaft of the screwdriver about a quarter inch away from a good ground source. Have your assistant turn the key and crank the engine while you check to see if you have spark. If you can, visit your local parts store and ask for a noid light that will fit your vehicle. It's usually about $10-$12. The purpose of the noid light is to check for injector pulse. Disconnect the plug for the injector and connect the noid light in it's place. Once again, crank the engine and check to see if the noid light lights up and pulses. If the crank sensor is bad, you should have no spark and no injector pulse. Replace crank sensor if so. If you have spark, check for fuel and or fuel pressure. Listen for the fuel pump to energize when the key is turned. Also try spraying starting fluid into the throttle body. If it starts, your having fuel issues. I hope these tips help. Good luck.

Feb 21, 2015 | 2004 Dodge Durango

1 Answer

Engine starts but wont run


You will have to pinpoint what the engine is missing...
- Spark
- Fuel
- Compression

All three of these are tested when the engine is being cranked over. There are two way of checking for fuel. Fuel pressure and fuel trigger. Both are very important and must be present for the engine to start. Fuel pressure is self explanatory. You just hook up the gage and see what the reading is. Fuel trigger is check with a noid light. The injector gets unplugged and the noid light gets plugged in to the injector clip. With the engine cranking over, this light must blink. This is the signal to the injectors from the computer. You can have all the fuel pressure in the world, but it wont matter if the injector is not pulsing gas into the cylinder like it should.

Compression tester, spark tester, fuel pressure gage and noid light are all accessible at your local auto store. All three tests play a very important part in diagnosing a no start condition. Be extremely careful when doing these tests.

Thank you for using FixYa, have a nice day.

Jan 13, 2013 | 1995 Jeep Grand Cherokee

1 Answer

Car turn over but wont start


Hi there:
You will have to pinpoint what the engine is missing... Spark / Fuel / Compression

All three of these are tested when the engine is being cranked over. There are two way of checking for fuel. Fuel pressure and fuel trigger. Both are very important and must be present for the engine to start. Fuel pressure is self explanatory. You just hook up the gage and see what the reading is. Fuel trigger is check with a noid light. The injector gets unplugged and the noid light gets plugged in to the injector clip. With the engine cranking over, this light must blink. This is the signal to the injectors from the computer. You can have all the fuel pressure in the world, but it wont matter if the injector is not pulsing gas into the cylinder like it should.

Compression tester, spark tester, fuel pressure gage and noid light are all accessible at your local auto store. All three tests play a very important part in diagnosing a no start condition. Be extremely careful when doing these tests.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jun 23, 2012 | 2001 Oldsmobile Alero

1 Answer

Jag 2001 s type turns over but won't start


Hi there:
You will have to pinpoint what the engine is missing... spark / fuel / compression.

All three of these are tested when the engine is being cranked over. There are two way of checking for fuel. Fuel pressure and fuel trigger. Both are very important and must be present for the engine to start. Fuel pressure is self explanatory. You just hook up the gage and see what the reading is. Fuel trigger is check with a noid light. The injector gets unplugged and the noid light gets plugged in to the injector clip. With the engine cranking over, this light must blink. This is the signal to the injectors from the computer. You can have all the fuel pressure in the world, but it wont matter if the injector is not pulsing gas into the cylinder like it should.

Compression tester, spark tester, fuel pressure gage and noid light are all accessible at your local auto store. All three tests play a very important part in diagnosing a no start condition. Be extremely careful when doing these tests.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jun 19, 2012 | 2001 Jaguar S-Type

1 Answer

WONT START. NO FIRE


First check coils and battery charge. You will have to pinpoint what the engine is missing...
- Spark
- Fuel
- Compression

All three of these are tested when the engine is being cranked over. There are two way of checking for fuel. Fuel pressure and fuel trigger. Both are very important and must be present for the engine to start. Fuel pressure is self explanatory. You just hook up the gage and see what the reading is. Fuel trigger is check with a noid light. The injector gets unplugged and the noid light gets plugged in to the injector clip. With the engine cranking over, this light must blink. This is the signal to the injectors from the computer. You can have all the fuel pressure in the world, but it wont matter if the injector is not pulsing gas into the cylinder like it should.

Compression tester, spark tester, fuel pressure gage and noid light are all accessible at your local auto store. All three tests play a very important part in diagnosing a no start condition. Be extremely careful when doing these tests.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

May 11, 2012 | Toyota Celica Cars & Trucks

1 Answer

07 pontiac g5 gt wont start when put gas in it


You will have to pinpoint what the engine is missing...
- Spark
- Fuel
- Compression

All three of these are tested when the engine is being cranked over. There are two way of checking for fuel. Fuel pressure and fuel trigger. Both are very important and must be present for the engine to start. Fuel pressure is self explanatory. You just hook up the gage and see what the reading is. Fuel trigger is check with a noid light. The injector gets unplugged and the noid light gets plugged in to the injector clip. With the engine cranking over, this light must blink. This is the signal to the injectors from the computer. You can have all the fuel pressure in the world, but it wont matter if the injector is not pulsing gas into the cylinder like it should.

Compression tester, spark tester, fuel pressure gage and noid light are all accessible at your local auto store. All three tests play a very important part in diagnosing a no start condition. Be extremely careful when doing these tests.

Apr 16, 2012 | 2007 Pontiac G5 Gt Coupe

1 Answer

Cranks but will not start


Hi Jose:
You will have to pinpoint what the engine is missing...
- Spark
- Fuel
- Compression

All three of these are tested when the engine is being cranked over. There are two way of checking for fuel. Fuel pressure and fuel trigger. Both are very important and must be present for the engine to start. Fuel pressure is self explanatory. You just hook up the gage and see what the reading is. Fuel trigger is check with a noid light. The injector gets unplugged and the noid light gets plugged in to the injector clip. With the engine cranking over, this light must blink. This is the signal to the injectors from the computer. You can have all the fuel pressure in the world, but it wont matter if the injector is not pulsing gas into the cylinder like it should.

Compression tester, spark tester, fuel pressure gage and noid light are all accessible at your local auto store. All three tests play a very important part in diagnosing a no start condition. Be extremely careful when doing these tests.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Feb 16, 2012 | 1992 Toyota Celica

1 Answer

Lexus will not start


Hi there:
You will have to pinpoint what the engine is missing...
- Spark
- Fuel
- Compression

All three of these are tested when the engine is being cranked over. There are two way of checking for fuel. Fuel pressure and fuel trigger. Both are very important and must be present for the engine to start. Fuel pressure is self explanatory. You just hook up the gage and see what the reading is. Fuel trigger is check with a noid light. The injector gets unplugged and the noid light gets plugged in to the injector clip. With the engine cranking over, this light must blink. This is the signal to the injectors from the computer. You can have all the fuel pressure in the world, but it wont matter if the injector is not pulsing gas into the cylinder like it should.

Compression tester, spark tester, fuel pressure gage and noid light are all accessible at your local auto store. All three tests play a very important part in diagnosing a no start condition. Be extremely careful when doing these tests.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Feb 13, 2012 | Cars & Trucks

1 Answer

My 95 buick lesabre will not start , I have change to a new fuel pump and a new cam shaft sensor. The gas is getting to the fuel rail, I have spark on all six cylinders . If i spray gas in through the mass...


Thee are a couple of things left to check. One is to hook up a fuel pressure gauge to the fuel rail and see how much pressure your getting and compare it to specs. It maybe getting fuel there but not enough pressure. To see if the injectors are being pulsed you wil need a set of noid lights. You will unplug an injector and plug in the noid light. It will flash everytime that injector is pulsed. If it never flashes your injector drivers on the ecu are bad.

Sep 20, 2010 | 1995 Buick LeSabre

1 Answer

Talked several days ago about 2001 toyota sienna no spark no noid light pulse has fuel pressure no trouble codes changed crankshaft position sensor no fix 3.0l where is camshaft position sensor located...


Front part of the engine, above the front exhaust manifold to the right. Its usually black/grey sensor with an eletrical connector running from the RH side of the engine. By the way the cam sensor controls spark, the crank sensor controls fuel pulse. hopefully this helps

May 11, 2010 | Toyota Sienna Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...