Question about 2002 Volkswagen Jetta TDI

1 Answer

Replacing engine head and need to know the torque on a 2002 vw jetta head bolts

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

If its a diesel 8v or a petrol then its 40 nm, 60 nm, 90 degree, 90 degree

Posted on May 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need too know the torque specs on head bolts and crankcam 2.4 engine


on a 2002 2.4 engine head bolts are 'torqued to distance'.

First, install all the bolts, and, in a sequential fashion, starting at the innermost, working outward, torque all bolts to 70 N-m/806 kgf-cm/58 foot lbs.

Next, mark the front side of each head bolt with a dot of paint. Retighten the cylinder head bolts 90 degrees, starting at the inner 2, and working outward.I dont thin anything has changed on this engine since then.

Mar 19, 2013 | 2005 Toyota Camry XLE

2 Answers

I need head bolt torque sequence for 2002 nissan altima 2.5s engine


hello I have 2007altima 2.5s will replace the gasket I just want to know what is the torque for mounting screws

Aug 15, 2012 | 2002 Nissan Altima

1 Answer

1992 vw jetta 1.6 turbo diesel,what is the cylinder head bolt torque spec?


!st thing is get the revised head gasket (used on 1993 up) for this engine from VW or Felpro, always use new head bolts or a repeat failure will occur. Using the revised head gasket here is the procedure to torque the head down, it is done in stages. PLease go to this site and read the whole procedure.

Feb 07, 2012 | 1992 Volkswagen Jetta

1 Answer

I need to know the size tool to use to remove the caliper bolts on the back brakes on a 2002 VW Jetta wagon TDI - standard star sizes are not working.


They are Torx heads on the calibers, the parts store sells them in a 4-pack for German cars. You will need a special tool to retract the caliper pistons also.

Aug 17, 2011 | 2002 Volkswagen Jetta TDI

1 Answer

How many motor mounts need to be replaced on a 2002 vw jetta 1.8t


YOU HAVE 3 MOUNTS. YOU HAVE PASSENGER SIDE ENGINE MOUNT. YOU HAVE DRIVER SIDE ENGINE MOUNT AND THE LOWER TORQUE STRUT MOUNT TO TRANSAXLE.

Feb 20, 2011 | 2002 Volkswagen Jetta TDI

2 Answers

I have a 2002 VW Jetta and the temperature gauge keeps going up and down... Is this something to worry about ?


Replace the Engine Coolant Temperature (ECT) sensor. ECT sensor is placed in the right back side of the cylinder head on 2002 VW Jetta 1.9 TDI. See picture below:

tdisline_212.jpg

Please do rate my response. Thanks!

Feb 04, 2011 | 2002 Volkswagen Jetta TDI

3 Answers

I need torque settings for the engine ie head bolts v6 engine 1


i am replacing the heads on a GMC 350 cu in engine. what is the final torque of the head bolts?

Jul 15, 2010 | 1985 Chevrolet Camaro

1 Answer

I need the cylinder head torque settings for the 1.9 tdi turbo engine on my 2002 jetta


4 steps, starting from center and doing the normal pattern. 30 ft lbs, then 44 ft lbs.

3rd step 1/4 turn

4th step addional 1/4 turn. Make sure you are using new bolts.

Jul 15, 2009 | 2002 Volkswagen Jetta TDI

1 Answer

2000 VW jetta; what is the torque for valve cover and plenum


I briefly looked online and did not see any info direct6ly relating to the torque spec of the cover bolts. I would guess around 15 ft lbs.--not too much--the head is aluminium--best way to go is to walk up to the service counter of the VW dealer and ask him to provide that information. You have the car and they built it!

Apr 09, 2009 | 2000 Volkswagen Jetta TDI

1 Answer

VW Jetta torque setting and hub nut size????


129 ft/lbs. Per Bentley...I'm pretty sure it's a 30 mm 12 point socket.

Mar 13, 2009 | 2002 Volkswagen Jetta TDI

Not finding what you are looking for?
2002 Volkswagen Jetta TDI Logo

Related Topics:

183 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75197 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...