Question about Cars & Trucks

1 Answer

I have a 2000 Saab 93e, the clutch petal drop to

I have a 2000 Saab 93e the clutch petal drop to the floor and I have no pressure.

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 771 Answers

Is the clutch fluid reservoir empty? If so you have a leak as the fluid will not appreciably go down even with years of use. Check around the foot well inside the car and around the reservoir tank for signs of fluid loss. If the foot well carpet is soaked it is likely the master cylinder seal needs replacing. If the area around the reservoir is wet then the union from the reservoir or to the pipe connected to the slave cylinder needs to be tightened from the reservoir. If there is no sign of a leak then the leak is associated with the clutch slave cylinder, either at the pipe union, the bleed nipple or the cylinder seal. The first two will be obvious to identify on the cylinder itself. The seal leak may well be indicated by drips coming from the junction between the gear box bell housing and the engine block. The slave clutch can usually be refurbished with a repair kit that includes a new seal. Take care when removing the clutch fluid feed pipe not to bend or damage it so that it can be easily re-used when reinstalling the salve cylinder.

Posted on May 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where do you add clutch fluid on a 97 Saab 900 SE?


there is a small tank to put fluid in should be on the firewall if the pedal went to the floor the line broke or the slave cylinder for the clutch went bad

Oct 17, 2017 | Saab Cars & Trucks

1 Answer

Purchase 2000 saab 9.3 2.0 turbo previous owner said replaced clutch etc without depressing clutch!!!engine running !!!shifter can be put in all positions 1 through 5 and Reverse..??no movement.


I suspect that the throw bearing carrier has been fitted on the wrong side of the throw out fork and has the pressure plate permanently disengaged.

Apr 20, 2015 | 2000 Saab 9-3

1 Answer

Clutch petal stays up with too much pressure car stays in neutral like pedal is pressed to floor


Sounds like an internal clutch/pressure plate issue. Possible broken torsional vibration spring in the clutch assembly keeping clutch engaged. The transmission will have to be removed and clutch inspected/replaced.

Apr 11, 2015 | 2008 Chevrolet Cobalt LT1

1 Answer

Bleeding clutch


Are you sure the clutch disc and fork are connected to the slave cylinder ?

Apr 29, 2013 | 1997 Isuzu Rodeo

1 Answer

What does it mean when the clutch petal goes all the way to the floor in my 2003 suzuki aerio


Your clutch fluid reservoir may need brake fluid-yes, it uses brake fluid as a hydraulic fluid. Check reservoir on the firewall. It will sit beside the brake master cylinder. The reservoir sits atop the clutch master cylinder.
If it was dry, the clutch may need bleeding down at the slave cylinder on the transmission housing-where the clutch fork sticks out of the transaxle.. Open the bleed valve on the slave cylinder, and have someone slowly press clutch down. Keep bleeding until a steady stream of fluid comes out when clutch is pressed. Then close bleed valve, check clutch operation-pedal should have some pressure on it now.

Dec 10, 2012 | Cars & Trucks

2 Answers

I have a 2000 Isuzu Rodeo in which the clutch pedal went to the floor & stayed there. Upon inspection, the clutch master cylinder was empty on fluid. I filled the reservoir & bleed the clutch...


It sounds as if you have 2 problems here.

The fact that the clutch pedal went to the floor and stayed there suggest a fault in the master cylinder. It may be that you need to overhaul the master cylinder.

Overhaul kits are available at less cost than a clutch master cylinder:
0results for isuzu rodeo clutch master cylinder overhaul kit

The grinding noise ... A grinding noise would be caused by either the gear not engaging properly because of the defective clutch.

Or, if it is more of a squealing noise - that may be the clutch release bearing at fault.

Are you absolutely sure that your entire clutch unit - pressure plate, driven plate and release bearing aren't worn?
116results for isuzu rodeo clutch

Mar 14, 2017 | 2000 Isuzu Rodeo

1 Answer

Saab 2000 93 hot aero clutch problem??? I was parking out side my house, the clutch hit the floor no pressure . I returned the pedal and managed to get the reverse gear out, i do not know where the top up...


sorry to hear that mate, your slave cylinder has gone, you will need a replacement and more than likely a clutch as well if any fluid has contaminated the clutchplate, aero clutch is around

Jul 04, 2010 | Saab 9 3 Cars & Trucks

2 Answers

Clutch has no pressure, but no leaks.


That would be a pressure plate problem.

Jun 08, 2009 | 1989 Ford Probe

1 Answer

Brake petal goes to floor


if you cant find any leaks in lines or cylinders or calipers u probaly have a bad booster
see lots come threw my shop like that but also their is a vacum line that runs to the booster and it hooks to a plastic valve that goes in to the booster those get gloged and you loose pedal as well try replacing that before you bye a new boooster

Mar 26, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Clutch will not release


remove the gearbox to replace the clutch.this will teach you not to hold it on hills on the clutch but to put handbrake on and neutral.also the same at traffic lights and no boy racer flying starts where accelerator is floored and clutch ridden slowly to get most power to wheels,still its not difficult to change and clutches not that expensive if you do it yourself,garage price around 800 euros

Nov 17, 2008 | 2001 Daewoo Lanos

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

167 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...