Question about 2000 Daewoo Lanos

Open Question

Rear wheel bearings

How do I remove the hub so that I can replace the wheel bearings - Daewoo Cielo 98? Please provide a diagram if possible. Thank you.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
chiquititas
  • 1010 Answers

SOURCE: daewoo cielo speedo problem

Oh, i had this problem! you need to replace the clock i don't know the name but you need to replace the thing that shows you in which speed you are and the time and things.

Posted on Jun 17, 2008

Ad
  • 1 Answer

SOURCE: 1995 Toyota Celica Front Wheel Hub

The same thing happened to my 95 Celica, the first mechanic or suspension shop replaced the front wheel bearings and about a month later the noise was back. I took it to another shop and they said that the bearing were bad because the base of the spindle assemble,where the bearing sits, was wallowed out. They replaced it and the bearings and all is good. I would have them check the spindle assembly.

Posted on Jun 20, 2008

  • 56 Answers

SOURCE: Daewoo Cielo losing power

DEALER ISSUE, TAKE IT TO THEM.

Posted on Oct 13, 2008

  • 95 Answers

SOURCE: nissan sentra gxe 03 rear wheel hub bearing problem

Easy job ! just rem to get a gear puller for the antilock gear and install same as came off old one Parts around 100$ each apx 1/2 hr each side

Posted on Oct 15, 2008

losflip
  • 94 Answers

SOURCE: 2001 monte carlo ss. Rear wheel bearings making a grinding noise

It is pretty easy, there is not much labor involved if it has anti-lock brakes in the rear you will also have to un-plug the wire harness attached to hubs.

Posted on Nov 26, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to repair volvoxc90 rear wheel hub/bearings


1. Remove the tire/wheel
2. Remove the top and bottom caliper
bolts/remove caliper.
3. Remove the four bearing housing bolts on
the inside of the housing
You will need a soft mallet to whack the housing until it comes out...don't worry you cannot hurt anything but you hands and your pride.

Jul 24, 2012 | 2003 Volvo XC90

1 Answer

I need to replace the front wheel bearing for my 2001 Buick LeSabre LI. I need diagrams, step-by-step instructions, and tools needed if possible. Thank you in advance for your assistance.


no diagrams available. remove the entire disc brakes and rotor
remove the axle nut
remove the ABS plug to brake sensor
remove the 3 bolts from the hub
pull the hub off and reverse this proceedure

Jul 15, 2011 | 2001 Buick LeSabre

1 Answer

How to replace rear wheel bearing on 2003 hyandia sonata


Hub & Bearing Removal & Installation To Remove:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Release parking brake.
  2. Remove rear wheel assembly.
  3. Remove rear wheel speed sensor from carrier.
  4. Dismount brake caliper and support with mechanic's wire.
  5. Remove brake disc.
  6. Remove 4 axle hub mounting bolts. Special tool 09432-11000 (Typical) hyundai-08-00-6021.gif

  7. Using tool 09432-11000 (or suitable gear puller), remove tone wheel.
  8. Remove carrier.
  9. Remove stakes and remove flange nut.
  10. Support bearing outer race flange and press rear axle hub out.
  11. Using tool 09432-11000 (or suitable puller), remove inner race from axle hub.
To Install:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Apply thin coat of grease to bearing contact surface and hub.
  2. Using and appropriate tool, press bearing into hub. CAUTION
    Do not press against outer race of wheel bearing.
  3. Install flange nut and stake nut until it meets concave portion of spindle.
  4. Install carrier.
  5. Use an appropriate tool to press tone wheel.
  6. Install hub/bearing assembly with rounded portion of outer race facing up.
  7. Install 4 hub/bearing assembly bolts and rotate hub to seat bearing.
  8. Measure wheel bearing starting torque with a spring balance or equivalent device.
    • Starting torque should measure 15.9 in lb (1.8 Nm) or less
  9. Install brake disc.
  10. Mount brake caliper.
  11. Install rear wheel speed sensor to carrier.
  12. Install rear wheel assembly.
prev.gif next.gif

Oct 28, 2010 | 2001 Hyundai Sonata

1 Answer

How to replace rear wheel bearings on a 2000 cougar?


Hi,welcome to fixya.


The rear wheel bearings are not adjustable. If the bearings make noise or become loose, they must be replaced.

Removal & Installation

With Drum Brakes

NOTE The wheel bearings are contained within the wheel hub and must be replaced as an assembly.

  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Remove the wheel and tire assembly.
  4. Remove the anti-lock sensor retaining bolt and remove the sensor.
  5. Remove the brake drum retainer and the brake drum.
  6. Remove the hub retaining nut dust cover.
    NOTE Do not use an impact gun to remove the hub retainer nut.


    0996b43f80232353.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Using suitable tools loosen and . . .


    0996b43f80232351.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. . . . remove the hub retaining nut dust cover
  7. Remove the wheel hub retainer nut.

    0996b43f8023234f.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Using suitable tools, loosen and . . .


    0996b43f80232352.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. . . . remove the hub retaining nut
  8. Slide the hub and bearing assembly off of the spindle.

    0996b43f80232350.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Carefully slide the hub and bearing assembly off of the spindle

To install:
  1. Reinstall the hub and bearing assembly to the spindle.
  2. Reinstall the hub retainer nut. Tighten the retainer nut to 170-192 ft. lbs. (230-260 Nm).
    WARNING Do not use an impact gun to tighten the hub retainer nut, otherwise the bearings may be damaged.
  3. Install the hub retaining nut dust cover.
  4. Reinstall the brake drum.
  5. Check the brake shoes for proper adjustment.
  6. Reinstall the anti-lock sensor and the retaining bolt. Tighten the retaining bolt to 7-8 ft. lbs. (9-11 Nm).
  7. Reinstall the wheel and tire assembly. Tighten the wheel nuts to 62 ft. lbs. (85 Nm).
  8. Lower the vehicle until the wheels are supporting the vehicles weight. This will properly load the suspension.
  9. Tighten the spindle-to-control arm bolt to 52-79 ft. lbs. (70-98 Nm).
  10. Tighten the tie rod-to-spindle bolt to 75-102 ft. lbs. (102-135 Nm).
  11. Finish lowering the vehicle.
Road test the vehicle and check for proper operation.
Thank You for using fixya........iluv2fish........Ray........

Jul 16, 2010 | 2000 Mercury Cougar

1 Answer

How to replace rear wheel hub


Sodium based grease is not compatible with lithium based grease. Do not lubricate the wheel bearings without first thoroughly cleaning all old grease from the bearing. Use of incompatible bearing lubricants could result in premature lubricant breakdown.
  1. Raise and support the vehicle safely.
  2. Remove the wheels.
  3. Remove the brake drum or brake disc.
  4. Remove the hub grease cap.
  5. Remove the cotter pin retainer, adjusting nut and flatwasher from the rear wheel spindle. Discard the cotter pin.
  6. Remove the outer bearing and cone assembly.
  7. Remove the rear hub from rear wheel spindle.
  8. Using Seal Remover (TOOL-1175-AC) or equivalent, remove and discard the oil seal.
  9. Remove the inner bearing cone and roller assembly.
  10. Clean the inner and outer bearing cups with solvent. Inspect the bearing cups for scratches, pits, excessive wear and other damage. If the bearing cups are worn or damaged, remove them using a Bearing Cup Puller (T77F-1102A) or equivalent.
To install:
  1. Throughly clean old grease from the surrounding surfaces. If a new hub assembly is being installed, remove the protective coating using degreaser.
  2. If the inner or outer bearing cups were removed, install replacement cups using Bearing Cup Replacer (T73-1202-A) or equivalent. Seat the cups properly in the hub.
If a bearing packer is not available, work as much grease as possible between the rollers and cages. Grease the cone surfaces.
  1. Using a bearing packer, pack the bearing cone and roller assemblies with a premium bearing grease.
  2. Place inner bearing cone and roller assembly in the inner cup. A light film of grease should be included between the lips of the new grease retainer.
  3. Install the retainer with Hub Seal Replacer (T83T-1175-B) or equivalent. Be sure the retainer is properly seated.
Keep the hub centered on the spindle to prevent damage to the retainer and spindle threads.
  1. Install the hub assembly on the spindle.
  2. Install the outer bearing cone and roller assembly on the spindle.
  3. Install the flat washer and nut. Tighten the nut to 18-23 ft. lbs. (24-31 Nm) while rotating the hub to set the end-play. Back off the nut and retighten to 18 inch lbs. (2 Nm).
  4. Install the new cotter pin.
  5. Install hub grease cap.
  6. Install brake drum or disc.
  7. Install the wheels.
  8. Lower the vehicle.

May 04, 2010 | 1998 Ford Windstar

2 Answers

How to replace rear wheel bearings


don't have topaz. maybe escort will help guide you.

Section 04-02: Suspension and Wheel Hubs, Rear 1996 Escort, Tracer Workshop Manual
REMOVAL AND INSTALLATION Wheel Bearing and Hub Assembly NOTE: Wheel bearings are not serviceable and should therefore be replaced as an assembly with the wheel hub (1104).

Removal
  1. Raise and support the vehicle.
  1. Remove the wheel and tire assembly.
  1. Remove the hub grease cap (1131) from the wheel hub.
  1. If equipped with disc brakes, remove the rear disc brake caliper (2552) and rear disc brake rotor (2C026). Refer to Section 06-04 for the removal procedure.
  1. If equipped with drum brakes, remove the two brake drum screws and the brake drum (1126).
  1. Unstake the rear axle wheel hub retainer (4B477) securing the wheel hub to the rear wheel spindle (4A013). Remove and discard the rear axle wheel hub retainer.
  2. Remove the wheel hub from the rear wheel spindle.

Feb 06, 2010 | 1990 Mercury Topaz

1 Answer

How to change a rear wheel bearing on a 1994 toyota camry


The rear wheel bearing on a toyota camry is replaced by replacing the wheel bearing and hub as a unit. this is a design change as compare to older models with two piece wheel bearings. Scotch drive wheels. Remove rear wheel. Remove rear brake drum. (note: if emergency brakes are applied you will not be able to remove brake drum) Remove dust cap and hub retaining nut. Hub should slide off as unit. Replace hub with new unit. Installation is reverse of removal.

May 30, 2009 | 1994 Toyota Camry

1 Answer

We are trying to replace my rear wheel bearing. Can anyone give any ideas how to get it apart?


here is how to replace it on a 2 wheel drive please do not forget to rate and comment about your experience today. 2-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake drum
    • Wheel hub nut
    • Wheel hub
    • Inner wheel bearing race from the hub
    • Snapring
    • Wheel bearing outer race from the knuckle

06017-esca-g92.gif
06017-esca-g93.gif
06017-esca-g94.gif
06017-esca-g95.gif 06017-esca-g96.gif

To install:
  1. Install or connect the following:
    • Wheel bearing in to the knuckle
    • Snapring
    • Wheel hub into the wheel bearing
    • Wheel hub nut. Torque the nut to 214 ft. lbs. (290 Nm).
    • Brake drum
    • Rear wheel
    • Negative battery cable
06017-esca-g97.gif
06017-esca-g98.gif

Apr 11, 2009 | 2005 Ford Escape

2 Answers

Noisy front wheel bearing


It is possible but i do reccomend changing the bearing races in the hub when you do it to prevent any premature wear on your new bearings. A new hub/rotor assembly will come with new races installed if that makes it any easier.

    130890.gif
    tif.gif
moz-screenshot.jpgmoz-screenshot-1.jpg

Dec 12, 2008 | 1998 Chevrolet C1500

Not finding what you are looking for?
2000 Daewoo Lanos Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...