Question about 2000 Toyota Camry

1 Answer

Break lights not working after new light bulbs and fuses

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 160 Answers

Sound like possibilystop light swith located on end of brake pedal lever at top try unplugging and use jumper wire to diag otherwords if jumper wire makes lights come on you know it is the stop light switch kinda common..good luck please rate

Posted on May 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake lights wont work how do you fix that


if you dident put new bulbs in put them in if no success put in a new fuse for the break lights if they still don't work the only other thing can be your break light switch hope this helps.

Apr 23, 2014 | Cars & Trucks

1 Answer

Break lights 99 plymoth voyger


How about the fuse? Will they light with the turn signal? If they do then look at the turn signal switch.

Jan 10, 2014 | 1999 Plymouth Voyager

1 Answer

Passanger and third break light don't work, new bulbs and fuses installed. what should i check next?


I would check the turn signal switch first. The brake lights may go thru the switch depending on the configuration.

Aug 16, 2012 | 1992 Honda Accord

1 Answer

Break lights and blinkers not working


If you put the tester on the outlets and it lights up properly but the bulbs dont, you have already concluded that the wiring isn't the problem. unless of course the wires are corroded and simply putting the bulb in shorts it out. Have you tested the bulbs?

Jul 22, 2012 | 2008 Pontiac G6

1 Answer

None of my tail lights work. i changed the bulbs, tail light control board and fuses. I'm an electrician so i need a wire diagram of a 1996 chevy suburban


Your solution is a new combination switch,It also sounds like the hazard are activated and is non operation interfering with the brake light,but either way the solution is a combination swith

Jul 08, 2012 | 1996 Chevrolet Suburban

1 Answer

Break lights not working properly


hi
silly thing to sugest but would you have the brake/side light bulbs in the wrong way? if you look closley at the bulbs there is two pins either side on the round silver part. 1 pin sits higher than the other, make sure you fit the bulbs in the bulb holders to match the pins on the bulb sounds complicated but it realy is an easy mistake to make.

Jan 26, 2010 | 2004 Jeep Grand Cherokee

2 Answers

My brake lights stop working . So I replacd yhe light bulb but the brake light still don't work.


I know what it is. I have the same problem. Try, when pressing the break, pulling your turning signal lever towards yourself, but not all the way to turn on the brights. If your breaks light up then you need a new turn signal switch. Part of the switch disables the break lights when that flasher comes on, but when it goes bad, it wont let the lights com on at all.

Nov 05, 2009 | 1999 Chevrolet Monte Carlo

1 Answer

All fuses are good, lights bulbs are new whats wrong? but tail light work


check the break light switch it is should be at the top of the brake pedal you can unplug it and jump plug with a paper clip to test if lights work switch is bad

May 27, 2009 | 2000 Toyota Celica

1 Answer

2000 Saturn sl2 tail lights


If the 2000 Saturn SL2 is the same as the '99 SL2, then your tail lights bulb is the same bulb as your break light bulb. Now they are dual bulbs, just like your head lights. So just the same way that your brights can work, but your headlight lamp be out, or vice versa, is the same with your break lights. So replace both bulbs and you should be good to go. I just had to replace both mine, one was a tail light out, and the other's break light was out, either way, same bulb. Also, check your manual for the light, or take the light out when you go in to get new ones. I found that for some reason there is some confusion on the bulb in this make in model.

Feb 20, 2009 | 1999 Saturn SL

Not finding what you are looking for?
2000 Toyota Camry Logo

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8557 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...