Question about 2008 Jaguar Xk Series

1 Answer

Have a 2000 intl detroit 60 engine water is getting in the oil what causes this?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 196 Answers

Blown head gasket or crack

Posted on May 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

On my 1993 detroit 60 12.7, one day the oil pressure dropped to 15 psi and the buzzer came on , now if I drive it 4 miles, pressure low and buzzer comes on.


I can only tell you that in my Cat engine, as the crank and rod bearings wore further and further, the oil pressure also got lower and lower. Perhaps one or more of you bearings has gone bad.
Good Luck

Mar 04, 2015 | Cars & Trucks

2 Answers

Fault code 128s254-07 what does it mean


If you are referring to a check engine code for a Detroit Diesel 60 series engine, there are several forum links that troubleshoot the bad code. 1 resolved code involved replacing wires to the ECM and replacing some bad batteries.

2000 Century DT 60 series Engine controller no response page 1
2000 Century DT 60 series Engine controller no response Page 2


Here is image of the wiring diagram the forum mentioned.
c0687617-5874-4473-98cd-a56ced317940.png

Apr 13, 2014 | Cars & Trucks

1 Answer

Operating oil pressure for 14.0l detroit dieselseries 60


If the engine is at normal operating temperature 25 pounds is fine at idle. Also have you tested the oil pressure with a mechanical gauge, if not you should do so.

Jun 10, 2012 | Cars & Trucks

1 Answer

I have filled the water reservoir several times a week. There is no leaks what could be wrong and where could the water be going?


Check the oil fill cap to see if there is any water or antifreeze leaking into the oil through a bad gasket in the engine. To much water getting into the oil will ultimately cause your engine to seize, ruining your engine. A light tan substance on the underside of the oil fill cap also is indicative of water getting into your oil.

Oct 26, 2010 | 2000 Volkswagen Beetle

1 Answer

2000 4 Cyl. 240+ compression on all Cyl. No water shows on the dip stick. Water and oil stand in all 4 plug wells. Coolant recovery tank is full of thick tan sludge of oil and water. Engine uses no oil but...


Hi,
This doesn't sound good. I would change the oil and get a report of what drained out. If it's milky sludge too, you have water getting into the oil.
Did the engine run hot? A blown head gasket could cause this oil in water issue. If that's the case, you may be in for an inspection of the engine to see what degree of damage if any... this is major. Don't let it go unattended.
Man, I hope I'm wrong. Good luck!

Jul 02, 2010 | 2000 Daewoo Leganza

1 Answer

Where is the oil pressure sensor located on a 60 series detroit


60 series detroit has oil sender on driver side near rear of engine just above the starter. It usually has 3 wires, and sometimes can be buried in the harness, so you may have to look under wiring harnesses in that area to find.

Dec 28, 2009 | 2008 Jaguar Xk Series

1 Answer

Oil pressure gage at 50


if pressure is higher than what it normally is after an oil change, you may have used the wrong grade of oil (too thick). Foam could be from overfilling, or from water in the oil (maybe antifreeze getting into the oil?).

Apr 01, 2009 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

196 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75077 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...