Question about 1996 Pontiac Sunfire

1 Answer

Cant start the engine after changing the fuel pump and the starter

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,857 Answers

What was the origninal problem so we can address the actual problem. What made you think the two part you changed were the problem. What testing did you perform to get to where you are now ??

Posted on May 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is crankshaft position sensor located 1996 gmc sierra 1500


The crankshaft position sensor is located on the right-side (passenger side) of the engine. At the rear of the engine, behind the starter. You need to remove the starter to remove the crank sensor. Remember to disconnect the battery first. The starter can short against the cross member.

Mar 03, 2014 | Cars & Trucks

1 Answer

Engine will not start when hot


Difficult to start with hot engine
1. Starter signal circuit.
- Switch off the engine.
- Connect the scan tool, if you have one.
- Switch on the engine (Do not start). Switch on the scanner.
- Select connect/ engine and power-train/ live data/ starter signal.
Note: Different scan tools can have different selection menus.
- Start the engine, watching the starter signal. If it changes from OFF to ON during starting, it is OK. If not then check the ignition switch and wiring for starter signal malfunction.
2. ISC valve circuit.
3. Fuel pump control circuit.
4. Fuel Injectors.
5. Ignition coil (w/ Igniter)
6. Spark plugs gaps.
7. Specific gravity and health of the battery.
8. ECU ground connectors for firm and clean connection to the engine. (Bunch of brown wires with metallic connectors).
9. Starter motor. (250 rpm).
Hope that works and thank you for visiting Fixya.

Jan 21, 2014 | 2004 Toyota Corolla

1 Answer

Mercedes 300e 1989. Pre ignition when I turn the key off and still wont start. any help


if starter turns and engine will not ignite remember it is fuel, electrical or mechanical check the fuel pump relay then fuel pumps the relays do fail after 20 years the pumps rarly fail.
Did you change the fuel filter?
if starter does not turrn start checking
Fuses
Relays
Starter
Switch
electrical gremlins are challenging but if you are systematic and have a wiring digrahm you will find the problem

Jan 07, 2014 | Cars & Trucks

3 Answers

1999 surburban won't start getting gas and fire. put new coil and check fuel pressure from fuel pump. what can it be,


my 1999 chevy suburban will start with starter fluid bbut wont stay running already replaced coil,rotor on distribitor,and oil pump cant seem to figure it out any ideas

Jan 17, 2011 | 1999 GMC Suburban

3 Answers

My 1981 Cadillac Deville 5.7L Diesel wont start. Ive checked all that I know including starter,battery,alternator,etc. Also, checked fuel pump, feul filter, fuel lines, injection pump. I topped off all of...


What does changing the oil,changing filters etc,have to do with the vehicle not starting?
What actual testing was done on --battery,alt,starter.fuel pump,etc.,how was this testing conducted and what were the results?
No fluids are consumed, in any motor vehicle,
If you have to top off,you have a leak,repair it!!

Sep 20, 2010 | Cadillac DeVille Cars & Trucks

1 Answer

Changed fuel pump and fuel filter, now x5 2002 won't start


1. use scanner to find out if there's trouble code.

2.. it's not clear if the starter (motor) turns as you try to start the engine, if not, check starter motor including intermittent (maybe) problem with the ignition switch.

3.if starter motor turns everytime you try to start: check the electrical ignition system: coils & spark plugs

Apr 30, 2010 | 2002 BMW 5 Series

1 Answer

97 buick skylark wont start


if starter fluid made it chug, I would suspect fuel pump fuse, relay or pump, also fuel filter.

Dec 29, 2008 | 1997 Buick Skylark

Not finding what you are looking for?
1996 Pontiac Sunfire Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...