Question about 2000 Nissan Altima

2 Answers

2002 nissan altima po507 idle control system the rpm to hgh

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 564 Answers

Replace tps (throttle posistion sensor) some call it idle speed control module either way it needs to be replace. its located on or near the throttle body.

Posted on May 07, 2010

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

More details on PO507

Posted on Nov 25, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2002 Nissan Altima Cold air blows at idle but is warm at higher engine RPM


Heater core may be clogged. Try flushing it to see if water flows through freely. Also check the heater water control valve for restrictions.

Dec 15, 2017 | 2002 Nissan Altima

1 Answer

What does code po507


The P0507 means Idle Control System RPM Higher Than Expected

car diagnostic scanner

Aug 17, 2012 | 2003 Mercury Mountaineer

1 Answer

2005 sentra trouble code po507


P0507 - Idle Air Control System RPM Higher Than Expected

Could be vacuum leak, dirty throttle body, faulty IAC

Jan 06, 2012 | Nissan Sentra Cars & Trucks

1 Answer

I need to set the timing on my 2002 nissan altima


  • Tools needed: A timing light and wrenches.
  • Locate the crankshaft pulley at the front of the Altima's engine and clean it off to expose the timing marks. Start the car and turn off any accessories such as climate control, lights and the radio. Allow the engine to idle until it reaches normal operating temperature.
  • Turn off the engine and connect a tachometer to the distributor per the manufacturer's instructions. Connect the timing light to the battery and then to the number one ignition wire. Start the engine and verify it's idling at 1,000 RPM. Adjust the idle speed if necessary

  • Point the timing light at the crankshaft pulley to determine the amount of adjustment needed. Adjust the timing by loosening the distributor mounting bolts and turning the distributor until the crankshaft timing mark lines up with the middle line of the timing light.

  • Tighten the distributor mounting bolts and recheck the timing. Turn the Altima off and remove the tachometer and timing light. Reconnect the number one ignition wire.
  • Oct 07, 2010 | 2002 Nissan Altima

    3 Answers

    My nissan is showing this code p0507. What is that mean.


    idle controll system idle to high is the code description

    Jun 09, 2010 | 2003 Nissan Maxima

    2 Answers

    The RPM of Nissan Altima stays high when drive over 65 MPH.


    No....the rpms differ from engine to engine and from manufacturer to manufacturer. RPM's are always higher at higher speeds.

    Aug 25, 2009 | 2002 Nissan Altima

    1 Answer

    I'acontrol m working on a 2002 nissan altima.


    where is the ac relay on a nissan altima 2002

    Aug 04, 2009 | 2000 Nissan Altima

    1 Answer

    Fault codes, p0102,p0122,po507


    po102--maf sensor, could be a bad air cleaner and not letting air into engine, po122--tps pedal position sensor low, replace or adjust tps sensor,or wiring,po507--idle control system high input. for this you can take off idle air control, and clean out carbon from were it mounts on engine. it is just before throttle body at end of air intake hose, it is black. do not push on pintle on end of valve when cleaning, use a old toothbrush to clean carbon off of valve, use carb cleaner but do not soak valve in liquid of any kind. good luck!!

    Mar 20, 2009 | 1999 Chevrolet Malibu

    Not finding what you are looking for?
    2000 Nissan Altima Logo

    687 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Nissan Experts

    yadayada
    yadayada

    Level 3 Expert

    77499 Answers

    Phil Lovisek
    Phil Lovisek

    Level 3 Expert

    726 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22306 Answers

    Are you a Nissan Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...