Question about 2006 Chevrolet Uplander

1 Answer

INEED TO CHANGE HEADLAMP BULB HOW DO iTAKE OUT HEAdlamp to change the bulb

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Contributor
  • 181 Answers

Heres instructions and picture

iNEED TO CHANGE HEADLAMP BULB HOW DO iTAKE OUT - f90e8cf.gif7a16af1.gif

Posted on May 07, 2010

  • billmartin44 Jan 15, 2011

    This was helpful, but it is not apparent HOW one goes about "Pull the headlamp forward...".
    There must be another screw somewhere that is not mentioned.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change headlight lamp in 2005 Pontiac g6


To change the bulbs you need to first remove the 5 plastic pop screws on the front bumper. They're spread out at the top of the bumper right under the hood. Once you get those out, you have to remove the two hex bolts on each headlight. Then it gets tricky. You need to pull the light towards the front of the car until it pops out of the ball-bearing type mount on the fender. Once that pops out, you have to pull the front bumper forward while maneuvering the headlight out towards the front.

As per the manual it says as follows:---

Open the hood.

Hold the headlamp to prevent damage to the headlamp or to the fascia. Remove the bolts from the headlamp assembly. Remove the push-in-retainers across the front fascia. Remove the headlamp assembly. Lift the headlamp upward to release the locating tab from the front edge of the fender.

Disconnect the electrical connector from the headlamp assembly.

Remove the headlamp bulb access cover by rotating the headlamp bulb access cover counterclockwise, if necessary.

Remove the headlamp bulb from the housing by rotating the socket counterclockwise, if necessary.

Disconnect the headlamp bulb electrical connector, if necessary.

Remove the park/turn bulb access cover by rotating the cover counterclockwise, if necessary.

Remove the park/turn bulb from the housing by rotating the socket counterclockwise, if necessary.

Gently pull the park/turn bulb from the socket, if necessary. Install the park/turn bulb into the bulb socket.

Install the park/turn bulb socket into the headlamp housing by rotating the socket clockwise.

Install the park/turn bulb access cover by rotating the cover clockwise.

Connect the headlamp bulb to the headlamp electrical connector.

Install the headlamp bulb into the headlamp housing. Rotate the socket clockwise until locked.

Install the headlamp bulb access cover by rotating the cover clockwise.

Position the headlamp assembly to the vehicle. Lift the headlamp upward to release the locating tab to the front edge of the fender.

Install the bolts to the headlamp assembly. Tighten the bolts to 2 N·m (18 lb in).

Install the push-in-retainers across the front fascia.

Close the hood.

----------This will help.thanks.Helpmech.

Dec 25, 2010 | Pontiac G6 Cars & Trucks

1 Answer

How to change the headlight bulb on 2009 gmc sierra driver side


1. Loosen only, do not remove, the lower outside hidden headlamp bolt (2). 2. Depress the housing support tab with a flat-bladed tool downward in order to release the headlamp assembly from the support. 3. Pull the lamp assembly slightly forward to access the electrical connection. 4. Disconnect the forward lamp harness main electrical connector from the headlamp harness.
Headlamp Screws (Qty: 2)
1 Caution: Refer to Fastener Caution .
6 Nm (53 lb in)
O Headlamp Screw (Hidden)
6 Nm (53 lb in)
3 Headlamp Housing Support


Preliminary Procedure Remove Healamp
Remove either the LF or RF headlamp assembly. Refer to Headlamp Replacement (Chevrolet) Headlamp Replacement (GMC HD)
Headlamp Replacement (HD Diesel).
Headlamp Bulb (Hi)
Warning: Refer to Haiogen Bulb Warning .
Tip: Rotate the bulb socket a quarter turn counterclockwise and remove the bulb from the headlamp.
Headlamp Bulb (Lo)
Tip: Rotate the bulb socket a quarter turn counterclockwise and remove the bulb from the headlamp.

Need more come to https://www.autorepairhelp.us


change-headlight-bulb-2009-gmc-1pzbcmqursjjtd0qcfo11o2t-2-0.png change-headlight-bulb-2009-gmc-1pzbcmqursjjtd0qcfo11o2t-2-1.png

Aug 14, 2010 | 2008 GMC Sierra 2500HD 2WD

1 Answer

Change headlinght bulb


SECTION 417-01: Exterior Lighting 2005 Freestyle/Five Hundred/Montego Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/14/2005 Headlamp Bulb adobe.gif Printable View (327 KB) Freestyle, Five Hundredn0035265.gif
Item Part Number Description 1 — Headlamp bulb electrical connector (part of 14290) 2 13N021 Headlamp bulb

Montegon0035266.gif
Item Part Number Description 1 — Headlamp bulb access cover screws (6 required) (part of 13006) 2 13N019 Headlamp bulb access cover 3 — Spring retainer (part of 13006) 4 13N021 High intensity discharge (HID) bulb 5 14A411 HID bulb electrical harness 6 — High beam bulb electrical connector (part of 13006) 7 13N021 High beam bulb Removal and Installation
ani_caut.gif WARNING: The headlamp bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped. Handle the bulb only by its base. Avoid touching the glass envelope. Failure to follow these instructions may result in personal injury.
NOTE: The headlamp bulb should not be removed from the headlamp assembly until just before a new bulb is installed. Removing the bulb for an extended period of time may affect headlamp bulb performance. Contaminants may enter the headlamp assembly where they can settle on the lens and reflector. Never turn on the headlamps with the bulb removed from the headlamp assembly.
NOTE: Make sure the headlamp switch and ignition switch are in the OFF position.
Freestyle, Five Hundred
  1. Rotate the headlamp bulb 1/8-turn counterclockwise and remove the headlamp bulb.
    • Disconnect the electrical connector.
Montego
  1. Remove the headlamp assembly. For additional information, refer to Headlamp Assembly — Five Hundred, Montego in this section.
  1. Remove the 6 screws and the headlamp bulb access cover.
Montego high beam bulb
  1. Rotate the headlamp bulb 1/8-turn counterclockwise and remove the headlamp bulb.
    • Disconnect the electrical connector.
Montego HID bulb
  1. Release the spring retainer and remove the HID bulb.
    • Disconnect the electrical connector.
All vehicles
  1. To install, reverse the removal procedure.

2010&c18=modelyear&c20=n920901&c35=wsm%2cheadlamp%20bulb%2cs5f%2c417-01%2cremoval%20and%20installation&s=1600x900&c=32&j=1.3&v=y&k=y&bw=1171&bh=582&ct=lan&hp=n&[aqe]

Apr 02, 2010 | 2005 Ford Five Hundred

1 Answer

How to change lowbeam headlight bulb on 02 chev trailblazer


  1. Open and support the hood.
  2. Remove the grille.
  3. Pull up on the retaining tabs in order to remove the headlamp assembly from the headlamp panel.
  4. Disconnect the headlamp leveling electrical connector from the motor/actuator if equipped.
  5. Disconnect the headlamp electrical connector from the headlamp assembly.
  6. Remove the side marker socket from the headlamp assembly.
  7. Remove the park/turn socket from the headlamp assembly.
  8. Remove the headlamp assembly from the headlamp panel.
  9. Remove the access cover from the rear of the headlamp.
  10. Disconnect the electrical connector from the socket.
  11. Rotate the bulb and socket counter clockwise in order to remove the bulb and socket from the housing.
  12. Disconnect the electrical connector from the socket.
  13. Remove the bulb and socket from the headlamp.
Replace the low beam bulb with another low beam bulb. The low beam bulb has a gray tip and a grey socket.


Oct 17, 2009 | Chevrolet TrailBlazer Cars & Trucks

1 Answer

How to change front headlamp bulb? Low beam


  1. Open the hood.
  2. Remove Grille.
  3. Remove the 2 retainers on back of headlamp assembly and remove the headlamp from the sheet metal panel.
  4. Remove the access cover from the rear of the headlamp.
  5. Disconnect the electrical connector from the socket.
  6. Rotate the bulb and socket counter clockwise in order to remove the bulb and socket from the housing.
  7. Disconnect the electrical connector from the socket.
  8. Remove the bulb and socket from the headlamp.
Installation Procedure Important: • Replace a high beam bulb with another high beam bulb. The high beam bulb has a black socket. • Replace a low beam bulb with another low beam bulb. The low beam bulb has a gray tip and a grey socket.

Oct 14, 2009 | 2002 Chevrolet TrailBlazer

1 Answer

I need to change a dead bulb in my headlights and I dont have the owner manual.


96 sable, only ino I have. should be similar. Please rate, thanks

  1. sth~us~en~file=ani_caut.gif~gen~ref.gif WARNING: THE REPLACEABLE HALOGEN HEADLAMP BULB CONTAINS GAS UNDER PRESSURE. THE HALOGEN HEADLAMP BULB MAY SHATTER IF THE GLASS ENVELOPE IS SCRATCHED OR THE HALOGEN HEADLAMP BULB IS DROPPED. HANDLE HALOGEN HEADLAMP BULB CAREFULLY. GRASP HALOGEN HEADLAMP BULB ONLY BY ITS PLASTIC BASE. AVOID TOUCHING GLASS ENVELOPE. KEEP HALOGEN HEADLAMP BULB OUT OF REACH OF CHILDREN.
    NOTE: A properly aimed headlamp (13008) assembly normally need not be re-aimed after installation of bulb. A burned out headlamp bulb and retainer (13N021) should not be removed from the headlamp until just before a replacement headlamp bulb and retainer is to be installed. Removal of a headlamp bulb and retainer for an extended period of time may allow contaminants (dust, moisture, smoke) to enter the headlamp and affect the performance of the headlamp. When servicing the headlamp bulb and retainer, energize the headlamp bulb and retainer only while it is contained within the headlamp body.

    Make sure headlamp switch (11654) is in OFF position.
  1. NOTE: On some models the clamps holding the integrated relay control module (IRCM) may need to be unsnapped and the module pulled aside to gain access to the driver side bulb.

    Open hood and locate headlamp bulb through hole in upper radiator support assembly.
  1. Remove headlamp wire connector from headlamp bulb and retainer by pulling the connector and wires in a rearward direction.
  1. Remove headlamp bulb retainer (13N019) by rotating counterclockwise (when viewed from rear) about one-eighth turn and sliding headlamp bulb retainer off headlamp bulb and retainer. Keep headlamp bulb retainer as it will be used again to retain new headlamp bulb and retainer.
  1. Carefully remove headlamp bulb and retainer from opening in headlamp bulb (13007) by gently pulling straight out of opening. Do not rotate headlamp bulb and retainer during removal.
0a1a11c.gif

Jul 05, 2009 | 1991 Mercury Sable

1 Answer

I have 2006 Grand Prix How do I change head lamp?


Caution Halogen bulbs contain gas under pressure. Handling a bulb improperly could cause it to shatter into flying glass fragments. To help avoid personal injury:
Turn off the lamp switch and allow the bulb to cool before changing the bulb.
Leave the lamp switch OFF until the bulb change is complete. Always wear eye protection when changing a halogen bulb. Handle the bulb only by its base. Avoid touching the glass. Keep dirt and moisture off the bulb. Properly dispose of the used bulb. Keep halogen bulbs out of the reach of children.
Raise the hood.
Remove the headlamp assembly bolts from the upper fascia support.
Slide the headlamp assembly outward enough to release the headlamp bracket tabs from the slots in the upper fascia support.
Position the headlamp assembly away from the vehicle body to access the electrical connector.
Disconnect the electrical connector from the headlamp assembly.
Remove the headlamp assembly from the vehicle.
Disconnect the electrical connector from the headlamp bulb/socket.
Remove the headlamp bulb/socket retainer ring from the headlamp, by turning counterclockwise.
Remove the headlamp bulb/socket from the headlamp assembly.

Jun 13, 2009 | 2006 Pontiac Grand Prix

1 Answer

How do i change both headlights on my 2002 chevy cavillier


Removal & Installation To Remove:
  1. Remove or disconnect the following:
    • Hood close out filler panel.
    • Bolts from the headlamp.
    • Headlamp from the headlamp mounting panel.
    • Electrical connector from the headlamp.
    • Headlamp bulb/socket retainer ring from the headlamp.
c218bc4.gif

  • Headlamp bulb/socket from the headlamp.
  • Bolts from the headlamp adjuster mechanism.
  • Headlamp adjuster mechanism.
  • To Install:
    1. Install or connect the following:
      • Headlamp bulb/socket to the headlamp.
      • Headlamp bulb/socket retainer ring to the headlamp.
      • Headlamp adjuster mechanism to the headlamp housing, if necessary
      • Bolts to the headlamp adjuster mechanism. Tighten to 6 N.m (53 lb in).
      • Electrical connector to the headlamp.
      • Headlamp to the headlamp mounting panel and lower mounting bracket.
      • Bolts to the headlamp. Tighten to 10 N.m (89 lb in ).
      • Hood close out filler panel.

    Jun 06, 2009 | 2002 Chevrolet Cavalier Coupe

    1 Answer

    I need to change the headlamp bulb.


    1. Disconnect and isolate the battery negative cable.
    2. Remove screws attaching headlamp module to upper crossmember.
    3. Remove headlamp module from vehicle.
    4. Disconnect wire connector from back of headlamp.
    5. Remove bulb from headlamp unit.
    INSTALLATION

    CAUTION: Do not touch the glass of halogen bulbs with fingers or other possibly oily surface, reduced bulb life will result.

    1. Connect wire connectors to the back of headlamp module.
    2. Place headlamp module in position.
    3. Install screws attaching headlamp module to upper crossmember.
    4. Connect battery negative cable.

    Mar 21, 2009 | 2003 Dodge SRT-4

    1 Answer

    Hi, I have a 99 mercury cougar and I need to change the headlights. I am having difficulty finding the electrical connector so that I can pull the headlight assembly out and change the lights. Where is...


    Headlamp Bulb Removal
    1. Remove the headlamp assembly. For additional information, refer to Headlamp Assembly .

    Headlamp Assembly Removal
    1. Remove the radiator grille.7feecfa.gif

    Remove the headlamp assembly.
    2b42ecf.gif
    remove the cover/
    1. f76b11b.gif
    3.
    sxu~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not touch the glass of the bulb with your fingers.
    Remove the headlamp bulb (low beam bulb shown). 79891b8.gif

    Jan 10, 2009 | 1999 Mercury Cougar

    Not finding what you are looking for?
    2006 Chevrolet Uplander Logo

    Related Topics:

    330 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    75822 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8195 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...