Question about 1996 Ford F350 Crew Cab

1 Answer

Starts and will run and then off like someone turned the key off.

Checked codes and it had a code foer the controler so I replaced and it did not help and the relay in the fuse box will start chattering and truck will cut off.. When this happens the wait to start lite will be flikkering also.. If key is turned off and back on the wait to start lite is stady and truck will start and run for awhile and bang off... Would appreciate any info someone might have... Thanks..

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,924 Answers

Have you changed the fuel filter?And the relay?

Posted on May 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Great wall 2010 x240 will turn over but will not start can someone please help


check the condition of the fob key battery as it may be flat. check that the immobilizer is working correctly. Run fault codes to find sensor fault.

Nov 03, 2013 | 1998 Oldsmobile Intrigue

1 Answer

2005 Nissan Almeira code P1320 Primary Ignition Control, no problem or indication of problem existed and suddenly overnight vehicle would not start, managed to start vehicle after 1 hr struggle removing...


I think I would start with checking fuel pressure. You should have at least 40PSI at the fuel rail. You might have someone help you our and turn on the key while you get under your vehicle and listen for the whirrr of the fuel pump. It should cycle for about 3 seconds when the key is turned to the "ON" position to prime the system to start. If you can not hear the pump run or it does not sound smooth I think you will need to replace it.

Apr 20, 2013 | 2005 Nissan Almera 1.6

2 Answers

Good morning,we have a 1997 polo fuel injector car and it just dont want to start.We`ve already replaced the distributer and still nothing.Someone please help :-(


have the fault codes read . there are a few sensors that control the starting of the car including the engine immobiliser.

Apr 05, 2013 | Cars & Trucks

1 Answer

97 nisson pathfinder won't start some times after sitting over night.


Check the 10amp fuse 21 in the fuse box. If that is good, try to find the manifold vacuum solenoid valve. It s near the air filter as shown in the figure below. It will have two wires in the connector and two hoses attached. Test the valve by applying battery power to see if it opens. If not, replace the valve. If it opens, check the connector and wiring. The above steps are intended to resolve the 1105 code.
I'm not sure this code is making the truck hard to start. With good spark and fuel pressure, the next thing I would check is for AC voltage at the Injectors. Put an AC voltmeter on one of the injector connectors and watch the voltage while someone cranks the engine. Your meter should read at least 5 volts AC.

0996b43f8020336a-j1axptdruxmkgupulmd503d3-3-0.gif

0996b43f80254d38-j1axptdruxmkgupulmd503d3-3-2.gif

Aug 16, 2017 | 1997 Nissan Pathfinder

1 Answer

Engine turns over but will not start.


Hi there:

When the light comes on, one or more diagnostic trouble codes (DTC) are stored in the engine control module. These DTCs remain even if the light goes out. To address a Check Engine Light problem, the DTCs are retrieved and the appropriate troubleshooting information is followed in order to determine the problem.


Just scanned the computer and send us code number find it.

Hope helps.

Mar 14, 2012 | 1995 Dodge Ram 2500

2 Answers

My 1989 mustang GT's check engine light is on and it feels a little funny. like when it starts up it runs really good for about a minute then the RPM's sink sorta low and for a second i thought it was...


you must loosen the bolt they hold the distributor down to advance turn counter clockwise when it runs right lock it in place.clear all the codes and start over sounds like alot of them codes are from the past it may still need a coil pack ,disconnect the battery wait 3mins hook it back up and try it hope this helps

May 09, 2010 | 1989 Ford Mustang

2 Answers

Code: nobu5 *The truck runs fine for a little


replace both the asd relay and fuel pump relay and see if that works

Nov 25, 2009 | 1999 Dodge Durango

1 Answer

'02 Santa Fe V6 awd, Upon start up after a refuel you have to keep the revs up or it will stall,after that it starts fine.Also after running the a/c it doesn't want to shut off,turn the key back on and off...


One problem at a time please. No. 1!. Your description points to a faulty Purge Control Solenoid Valve (related to engine stall after refuel). The second problem could be caused by 'hot spots' in the combustion chamber -- however, the only way for any fuel to enter the combustion chamber after the KEY is turned OFF, is through the Purge Contro Solenoid Valve - it's the only component directly related to the problem you describe (unless you (or someone else) has modified the engine in some way other than original manufacture's design. Solution (provided no modifications have been performed), replace the Purge Control Solenoid Valve.

Jun 11, 2009 | 2002 Hyundai Santa Fe

3 Answers

1999 wrangler jeep not always starting


The reason you can't pull codes is that you have the "later" OBD system which can only be accessed with a scan tool.

Feb 01, 2009 | 1999 Jeep Wrangler

Not finding what you are looking for?
1996 Ford F350 Crew Cab Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...