Question about 1993 Toyota 4Runner

1 Answer

Power door locks

You sent me an answer that says check the hose split.....what has that got to do with power door locks???????????????????????????

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Master
  • 1,508 Answers

I didnt see the last answer. The last guy probably meant the hoses that the wires run in, into the doors from the body.

Near the hinges on each door is a rubber hose, that the wires go to the door locks and power windows,

Some times they get split or damaged and a wire can break

Posted on May 09, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why wont windows and lock work? could it be the front ecu?


Check inside of door where wiring comes thru for broken wires ,ECU doesn't control windows or door locks. You didn't state what model vehicle you own. But opening and closing door on drivers side causes broken wires on numerous vehicles over the years, most makes and models. Split boot and check all wires inside for breakage.

May 29, 2014 | Mitsubishi Galant Cars & Trucks

1 Answer

Door ajar displays, no power to rear wiper, rear window not locking


where the wiring goes from the rear door to the body of the car check for broken wires or take panel of and check all wires for braeks splits or bad connections

Mar 04, 2013 | 2007 Toyota FJ Cruiser

1 Answer

L door dose not lock all door locks


This may be due to a bad lock actuator, i will need to ask a few questions first.Can you lock the door by hand using the button? or is the lever stuck?Is the problem that it does not work with the power locks only?
Let me try to answer these, first if the door lock does not work with the power locks then the door lock actuator may be bad, the door panel will need to be removed and test for power at actuator. While inside the door check lock linkage.If the door lock lever wont move then that may also be related to a frozen lock actuator, that is the same as above. a bad or frozen lock actuator will not allow door to lock or unlock but sometimes a bad actuator will not work with the power button but will allow you to lock and unlock with lock lever or door key, the door panel needs to be removed to check . good day.

Apr 29, 2012 | 2000 Hyundai Sonata

2 Answers

Power door lock doesnt work


The power lock mechanism on these have this plastic gear setup and they crack. When it splits it just spins and makes that noise. You'll have replace the module, about $60 IIRC.

Feb 24, 2012 | 2003 Mazda Protege

1 Answer

Engine suddenly lost power and started skipping.


this model vehicle was famous for splitting the air intake hose.this would cause the mass air flow sensor door to close when accellerating.If engine idles fine and only stumbles when stepping on the gas. check the air intake hose for any cracks.

Nov 28, 2010 | 1993 Mazda 626

2 Answers

1999 - 2000 ford winstar sel power locks very weak ...hardly work work erratically...driver and passenger locks do not lock or unlock automatically.....8-(


On the 2000 Windstar that I was working on, the casing for the door lock actuators had split and the lock knob on the top of the door would twitch when I hit the button, but would not lock or unlock fully. I replaced the door lock actuators (in stock at my local dealership) and cleared up the problem. Also check the bushings that link the rods inside the doors. They are plastic and occasionally wear out

May 16, 2009 | 2000 Ford Windstar

1 Answer

My ford p100 turbo diesel 1993 runs well on tick over but when you drive it down the road it has no power whats so ever then when the turbo kicks in it picks up a little bit the turbo is working i,ve...


Check all turbo hoses first for splits etc. It's best to remove each one for a thorough inspection. If they are all ok you need to locate the small rubber hose that goes to the top of the injection pump. Check it. It's probably split somewhere. this ups the fueling when on boost. If its not intact you will have very little power.

Cheers
John

Apr 27, 2009 | 1993 Ford Escort 4 Door

1 Answer

Sliding doors won't lock or unlock using keyless.


there are 3 possibilities that I would check first. 1: make sure the contacts on the door, and body where the touch are clean. the lock and unlock signal are sent through these. 2: You may try replacing the battery in your key fob. 3: the power lock motors may have gone bad. To check, lock the doors with the drivers door panel, if they lock, they are fine. Another solution may be to recode your key fob. procedure for coding the fob to your vehicle can be found online.

Oct 21, 2008 | 1998 Chevrolet Venture Cargo

Not finding what you are looking for?
1993 Toyota 4Runner Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...